Power Connections - Honeywell Intelliguard 9000 Installation Instructions Manual

Hide thumbs Also See for Intelliguard 9000:

User manual (198 pages)

Programmer's manual (76 pages)

Installation manual (36 pages)

Table Of Contents

Table of Contents

Each CU COM is limited to a maximum of four KIDs and four

ISP devices. The CU supports four CC2s maximum, but

Honeywell recommends splitting the CC2s between the COM

ports.

1. At the selected I9000 CU mounting location, open the

CU housing and with the cover wide open, lift it up to

unhinge.

2. Mount the I9000 CU on the wall using four No. 8 round

or pan head screws.

3. Connect the wires to the I9000 CU as shown in Fig. 17.

4. Install the batteries that conform to the specification

listed in form no. 74-3035, Intelliguard 9000 Specifica-

tion Data.

R21

12V, 7A-h

1 2

3 4

1 2 3 4

EARTH

GROUND

14 AWG WIRE

–

BATTERY 1

BATTERY 2

12V, 7 AH

CLASS II (CURRENT LIMITING) PLUG-IN

TRANSFORMER (INPUT = 120V/60 HZ

INSTALL THE BATTERIES

IN THE I9000 ENCLOSURE.

CANADA P/N 5660-051, USA (P/N SILENT

KNIGHT MODEL 4165 ENCLOSURE WITH

MODEL 9220 TRANSFORMER) OR EQUIVALENT

18 AWG CABLE

50 FT (15M) MAX.

THE AX-5L CONDUIT ADAPTER (7003-162) MAY BE USED UNDER THE I9000 ENCLOSURE. THIS PERMITS CONDUITS WITH AN OUTER DIAMETER OF 0.75 IN. (19 MM) TO

PASS UNDER THE CONTROL UNIT AND BE TERMINATED SUCH THAT THE CABLES MAY ENTER THE I9000 ENCLOSURE THROUGH THE OVAL HOLE IN THE REAR OF THE ENCLOSURE.

IT IS NOT NECESSARY TO USE THE CONDUIT KNOCK-OUTS ON THE SIDE OF THE ENCLOSURE. THE I9000 IS 1 IN. (25.4 MM) FURTHER AWAY FROM THE WALL WITH THIS OPTION.

TO MEET CE CLASS B REQUIREMENTS, FERRITE BEADS MUST BE INSTALLED ON ALL THE CABLES EXITING THE I9000 ENCLOSURE. THE BEADS MUST BE LOCATED

AS CLOSE AS POSSIBLE TO THE I9000 ENCLOSURE BUT INSTALLED ON THE OUTSIDE. INSTALLING THE REQUIRED BEADS UNDER THE AX-5L CONDUIT ADAPTER SATISFIES

THE PROXIMITY REQUIREMENTS. SEE TABLE.

CABLE TYPE

MAXIMUM CABLE DIAMETER

LOW VOLTAGE 16 AC CABLE

10.15± 0.3 MM (0.400 IN)

ALL OTHER CABLES EXITING

6.6± 0.3 MM (0.260 IN)

THE CONTROL UNIT

TO PERFORM A COLD START OF THE ICP II, POWER DOWN THE SYSTEM AND HOLD DOWN S1 WHILE POWERING UP THE SYSTEM. THE YELLOW LED (DSI) LIGHTS FOR A FEW

SECONDS TO INDICATE THAT A COLD START HAS BEEN INITIATED.

EARTH GROUND. MUST NOT EXCEED 50 FT (15M) WITH 14 AWG WIRE.

Additional Intelligent Power Supplies

Each I9000 CU supports a maximum of seven Remote

Intelligent Power Supplies (RIPS). Depending on the

installation power backup requirements, up to two batteries

can be connected to the ISP. One ISP is located in the I9000

housing. The RIPS power devices used for detection and

control and each RIPS must have its own transformer. Fig. 18

shows the wiring for a Remote Intelligent Power Supply. The

RIPS is mounted in the same way as the I9000 control unit

shown in Fig. 19. The I9000 control unit is identical to an ISP

except that the ICP and RRI are not part of the RIPS

configuration.

INTELLIGUARD 9000 CONTROL UNIT 8003-332

INTELLIGENT SWITCHING POWER SUPPLY

(ISP) 8003-295

LEVER

1 2 3 4

THE TAMPER INPUT IS USED IN A RIPS (REMOTE

INTELLIGENT POWER SUPPLY). THE SWITCH IS

LOCATED IN THE ENCLOSURE.

PLACING A JUMPER BETWEEN THESE TERMINALS

ALLOWS THE COMM LED (DSI) TO FLASH WHEN THE

ISP IS POLLED. THE JUMPER IS USUALLY REMOVED IN

ORDER TO CONSERVE POWER.

12 VDC OUTPUT, 1A

FOR SOUNDING DEVICE

UNREGULATED 20 VDC,

NO BATTERY BACK-UP.

USED IN LOCAL SYSTEMS FOR A 750E GONG.

NON-SWITCHED

AC POWER

SOURCE

FERRITE BEAD INSTALLATION FOR CE

MANUFACTURER

FAIR-RITE NO. 0443167251

FAIR-RITE NO. 0443164251

Fig. 17. I9000 CU with ICP II, ISP.

5. Set the ISP siren output to steady or pulsating as shown

in Fig. 18.

6. Set the ISP address by setting switches S1-1 and S1-2

as shown in Fig. 18.

7. With power applied to the CU, follow the learning proce-

dure for the ISP. See the Additional Intelligent Power

Supplies section, step 5.

8. When the installation is fully commissioned, reinstall the

cover but do not close it.

9. From a CC2, enter the MODE menu using the techni-

cian ID and Code.

10. Close the CU cover and secure it into position.

11. From the CC2, press 4 to enter the RESET LOG menu

and press enter to reset the Event Log.

COLD START SWITCH

RST

COM 1

COM 2

DS4

DS1

INTELLIGENT COMMUNICATIONS

PROCESSOR II (ICP II) 8003-331

RS-485

POWER INPUT

15V MAXIMUM

COM 1 & 2

31 DEVICES

EACH MAXIMUM

12 VDC

COM 1

400 MA

WHT/GRN

WHT/BLU

3 PAIR

TWISTED

PAIR CABLE

22 AWG MINIMUM

CONNECT EACH DEVICE TO 12 VDC

AND TO EITHER COMM 1 OR COMM 2

BUT NOT BOTH, FOR EACH CABLE.

SUPPLIER

HONEYWELL (CANADA)

NEWARK P/N 91F6477

P/N 2500-002

NEWARK P/N 91F6476

P/N 2500-001

1. Install the Remote Intelligent Power Supplies, as

needed, near the devices to be powered.

2. Set the ISP siren output (S1-4) to steady or pulsating as

shown in Fig. 18.

3. Set the ISP address in each RIPS by setting switches

S1-1 and S1-2 as shown in Fig. 18. Each ISP on the

same COM line must have a different address.

4. Connect each RIPS to the I9000 as shown in the job

drawing. Refer to Fig. 17 for ground, battery and AC