Sharpening Chain - Bosch AKE 35-19 PRO Operating Instructions Manual

F016 L70 532 - Buch Seite 9 Donnerstag, 15. Dezember 2011 2:58 14
Replacing/Changing Chain
A
and Chain Bar
Fit the chain and chain bar as described in "Assem-
bly and Tensioning Chain".
The circular groove of the chain bar will wear partic-
ularly on the lower edge with time. When replacing
the chain turn the chain bar 180° to allow even wear,
thus extending chain bar life.
Reverse the chain tensioning catch 16 by removing
the screws and refitting it on the opposited side.
Check drive sprocket 21. If it is worn out or damaged
due to strain, have it exchanged by an authorized
Bosch service agent.

Sharpening Chain

Have your chain sharpened professionally at your
Bosch approved service agent or sharpen the chain
yourself using the Bosch sharpening kit or a Dremel
power tool with the appropriate grinder (1453), both
available at your Bosch approved service agent. Fol-
low the sharpening instructions supplied with the
sharpening kit.
Checking the Automatic Oiler
Proper functioning of the automatic oiler can be
checked by running the chain saw and pointing the
tip of the chain bar towards a piece of cardboard or
paper on the ground. Caution: Do not touch the
ground with the chain. Ensure safety clearance of
20 cm. If an increasing oil pattern developes, the au-
tomatic oiler is operating fine. If there is no oil pat-
tern, despite a full oil reservoir, see "Fault Finding" or
contact your Bosch approved service agent.
26 • F016 L70 532 • 08.05
Accessories
Chain
AKE 35-19 PRO
.........................................
AKE 40-19 PRO
.........................................
Chain bar
AKE 35-19 PRO
.........................................
AKE 40-19 PRO
.........................................
Cleaning
Chain sharpening/cleaning kit
Chain oil 1 litre
..............................................
Chain oil 5 litre
.............................................
Additional accessories
Gloves
..............................................................
Protective goggles
.....................................
SNR 19 ear protectors
(sounding proofing level 19 dB (A))
SNR 24 ear protectors
(sounding proofing level 24 dB (A))
Cleaning/Storage
B
Clean the moulded plastic housing of the chain saw
using a soft brush and clean cloth. Do not use water,
solvents or polishes. Remove all debris, especially
from the motor cooling vents 27.
Remove and brush clean the cover plate 15, chain
and chain bar after 1 to 3 hours of use.
Clean the area under the cover plate 15, the drive
sprocket 21 and chain bar assembly using a soft
brush. Clean oil outlet 19 with a clean cloth.
If the chain tensioning mechanism becomes dif-
J
ficult to operate, dismantle the protective lid 29 from
inside the cover plate 15. Turn locking knob 14 and
red tensioning ring 13 against each other, so that
debris is loosened from the mechanism and can be
discarded. Carefully knock out debris. If mechanism
is heavily clogged, use a soft brush or compressed
air for cleaning. Do not use tools of any kind.
If the chain saw is to be stored for a longer period of
time, clean chain and chain bar.
Store in a secure, dry place out of the reach of chil-
dren. Do not place other objects on the chain saw.
To prevent leakage ensure machine is left in a hori-
zontal position (oil filler cap 4 uppermost).
When storing machine in original packaging the oil
tank must be completely emptied.
English - 9
F 016 800 239
F 016 800 240
F 016 800 241
F 016 800 242
F 016 800 263
.............
2 607 000 181
F 016 800 111
2 607 000 134
F 016 800 178
2 607 990 042
...
2 607 990 043
...