Nozzle Recovery Function - MIMAKI JV-300-130 Operation Manual

Chapter 4 Maintenance

Nozzle Recovery Function

NOZZLE RECOVERY: When nozzles missing can not be
improved at specific points, other good nozzles can be
used as alternatives for printing.
1
Press the
key in LOCAL.
• MAINTENANCE MENU will be displayed.
2
Press , and press the
• "NOZZLE RECOVERY" will be selected.
3
Press the
• Printing of the nozzle pattern will start.
• Select "ENTRY" then "Move to select of the
Nozzle line (Step 4) without drawing a pattern"
Overhead view
Nozzle line
Nozzle pattern of Head 1
H1-A H1-B H1-C H1-D
310 310 310 310
301 301 301
290 290 290 290
281 281 281
270 270 270 270
261 261 261
250 250 250 250
241 241 241
230 230 230 230
221 221 221
210 210 210 210
201 201 201
190 190 190 190
181 181 181
170 170 170 170
161 161 161
150 150 150 150
141 141 141
130 130 130 130
121 121 121
110 110 110 110
101 101 101
90 90 90 90
81 81 81
70 70 70 70
61 61 61
50 50 50 50
41 41 41
30 30 30 30
21 21 21
10 10 10 10
1 1 1
• For 6-color ink sets, the nozzle patterns "H1-B"
and "H1-D" are not printed.
• When using leaf media, set a media of more than
A3 size put horizontally. If a media with narrow
width is set, printing will only be conducted to
midway.
4
Select the Nozzle line that needs NOZZLE
RECOVERY by pressing
press
Head No.
(H1 to H2)
4-12
(MENU)
key.
key twice.
H1-E H1-F H1-G H1-H
310 310 310 310
301 301 301 301
290 290 290 290
281 281 281 281
270 270 270 270
261 261 261 261
250 250 250 250
241 241 241 241
230 230 230 230
221 221 221 221
210 210 210 210
201 201 201 201
190 190 190 190
181 181 181 181
170 170 170 170
161 161 161 161
150 150 150 150
141 141 141 141
130 130 130 130
121 121 121 121
110 110 110 110
101 101 101 101
90 90 90 90
81 81 81 81
70 70 70 70
61 61 61 61
50 50 50 50
41 41 41 41
30 30 30 30
21 21 21 21
10 10 10 10
1 1 1 1
, and
key.
5
Register the Nozzle number that needs
NOZZLE RECOVERY and press
key.
(1) Select the registration number from 1 to 10
by pressing [][] key and press the
[ENTER] key.
(2) Register the nozzle number that needs
recovery by pressing [][] key and press
the [ENTER] key.
Registration number : 1 to 10
Example of nozzle to be recovered
Nozzle missing
No.128
301
281
261
241
221
201
181
161
141
121
101
81
61
Nozzle number
41
21
1
Nozzle missing No.16
Registration Recovery
number Nozzle No.
1 16
2 128
3 184
4 OFF
5 OFF
6
Press the
to end the setting.
• Up to 10 nozzles can be registered per 1 nozzle
line.
• Even if you use this function, time required for
drawing does not change.
• When printing has been done with the lowest path,
nozzle recovery is not reflected.
Moreover, depending on the conditions, there are
cases where only 20 to 120 nozzles are enabled at
both head ends (front and rear). Perform test
printing to confirm.
• When you use white ink, print on the clear film to
check.
Recovery nozzle No. or OFF
Nozzle missing
No.184
State
Target for nozzle recovery
Target for nozzle recovery
Target for nozzle recovery
No registration
No registration
key several times