To Service Personnel - Yamaha DV-SL100 Service Manual

DV-SL100

TO SERVICE PERSONNEL

1. Critical Components Information
Components having special characteristics are marked Z
and must be replaced with parts having specifications equal
to those originally installed.
2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated
from supply circuits.
Meter impedance should be equivalent to 1500 ohm shunted
by 0.15µF.
WARNING: CHEMICAL CONTENT NOTICE!
The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or
plastic (where applicable) components may also contain traces of chemicals found by the California Health and
Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR
ANY REASON WHATSOEVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes
or expose eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands
before handling food.
WARNING: Laser Safety
This product contains a laser beam component. This
component may emit invisible, as well as visible radiation,
which may cause eye damage. To protect your eyes
and skin from laser radiation, the following precautions
must be used during servicing of the unit.
1) When testing and/or repairing any component within
the product, keep your eyes and skin more than 30 cm
away from the laser pick-up unit at all times. Do not
stare at the laser beam at any time.
2) Do not attempt to readjust, disassemble or repair the
laser pick-up, unless noted elsewhere in this manual.
3) CAUTION : Use of controls, adjustments or
performance of procedures other than those specified
herein may result in hazardous radiation exposure.
Laser Emitting conditions:
1) When the Top Cover is removed, and the STANDBY/
ON SW is turned to the "ON" position, the laser
component will emit a beam for several seconds to
detect if a disc is present. During this time (5-10 sec.)
the laser may radiate through the lens of the laser pick-
up unit. Do not attempt any servicing during this period!
If no disc is detected, the laser will stop emitting the
beam. When a disc is loaded, you will not be exposed
to any laser emissions.
2
EQUIPMENT
WALL
OUTLET UNDER TEST
INSULATING
TABLE
Leakage current must not exceed 0.5mA.
Be sure to test for leakage with the AC plug in both
polarities.
警告：レーザーの安全対策
本機はレーザー光線を放射する部品を搭載しています。 こ
の部品が放射するレーザー光線は目に損傷を起こします。
このレーザー光線から目及び肌を保護するために、 本機の
修理作業中は下記の注意を厳守してください。
１） テスト時または修理時、 目及び肌を光ピックアップか
ら30cｍ以上離してください。 いかなる場合もレーザー
光線を見つめないでください。
２） 光ピックアップの再調整及び分解はしないでください。
３） このマニュアル上で指定されている以外の制御、 調整、
手順はレーザー光線を照射される結果を招く恐れがあ
ります。
レーザー放射条件
１） トップカバーを取り外しSTANDBY/ONスイッチをON
にすると、ディスク検知のため 5 ∼ 10 秒間、光ピック
アップからレーザー光線が放射されます。この間、修
理はしないでください。
ディスクが検知されなければ、レーザー光線の放射は
停止します。ディスクがセットされている場合、ディ
スクで遮られるのでレーザー光線は修理担当者に届き
ません。
AC LEAKAGE
TESTER OR
EQUIVALENT