Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Stanley FME721
Summary of Contents for Stanley FME721
- Page 1 FME721...
- Page 4 32 21...
-
Page 10: Intended Use
(Original instructions) Intended use Use of an RCD reduces the risk of electric shock. Your Stanley Fat Max FME721 sliding compound mitre saw has 3. Personal safety been designed for sawing wood, plastic and nonferrous metal a. Stay alert, watch what you are doing and use common only. - Page 11 The laser fitted must never be exchanged with a different saws. type of laser. Repairs to the laser should be carried out by authorised repair agents or Stanley Fat Max service staff. Do not use cracked/bent/damaged/deformed saw blades. Disconnect the machine form the mains before carrying Replace the table insert when worn.
-
Page 12: Residual Risks
Call Stanley Fat Max customer services for you nearest of the appliance by a person responsible for their safety. service agent. -
Page 13: Electrical Safety
2002/44/EC to protect persons regularly it must be replaced by the manufacturer or an authorised Stanley Fat Max Service Centre in order to avoid a hazard. using power tools in employment, an estimation of vibration exposure should consider, the actual conditions of use and the... - Page 14 ENGLISH (Original instructions) Assembly When installing a new blade, always check the lower limit position of the blade and if necessary, adjust it as follows: Warning! Before assembly, make sure that the tool is Unplug the tool. switched off and unplugged. Push the carriage toward the guide fence (9) fully and Note: This tool is accurately adjusted before shipping from lower the handle completely.
- Page 15 (Original instructions) ENGLISH Slide lock adjustment (Fig.11) Installing or removing saw blade (Fig.14, Fig.15, Fig.16) To unlock the track arm, turn the track arm lock knob (6) Caution: Always be sure that the tool is switched off and un- counterclockwise or clockwise. plugged before installing or removing the blade.
-
Page 16: Operating Instructions
ENGLISH (Original instructions) Thin material tends to sag. Support work piece over its entire Make sure the stock stop (13) on the left and right extension length to avoid blade pinch and possible kickback. table can be swung up as illustrated. Sliding sub-fence adjustment (left) (Fig.19, Fig.20, Guard release lever (Fig.24a) Fig. -
Page 17: Compound Cutting
(Original instructions) ENGLISH Pull the carriage toward you fully. parallel with the blade. If a force is applied perpendicularly to Switch on the tool without the blade making any contact the turn base or if the pressure direction is changed during a and wait until the blade gets up to full speed. -
Page 18: Maintenance
ENGLISH (Original instructions) the bevel scale (35) on the arm holder. the tool. If they do not point to 0º, loosen the screw (55) which Stopper pin is for carrying and storage purposes only and not secures the pointer (34) and adjust it so that it will point to for any cutting operations. -
Page 19: Protecting The Environment
3 x 30.5 cm bevel at 0º mitre, 45º bevel Should you find one day that your Stanley Fat Max product 3 x 21.5cm compound at 45º mitre, 45º bevel needs replacement, or if it is of no further use to you, do not dispose of it with household waste. - Page 20 If you wish to make a claim, contact your seller or check the location of your nearest authorised Stanley Fat Max repair agent in the Stanley Fat Max catalogue or contact your local Stanley office at the address indicated in this manual. A list of authorised Stanley Fat Max repair agents and full details of our after sales service is available on the internet at: www.
- Page 21 (Original instructions) ENGLISH 21 21...
- Page 24 United Kingdom Stanley Fat Max Tel. 01753 511234 210 Bath Road Fax 01753 572112 Slough, Berkshire SL1 3YD www.stanleytools.co.uk 90625440-PDF1 REV-0 06/2015...
Need help?
Do you have a question about the FME721 and is the answer not in the manual?
Questions and answers