Advertisement
Table of Contents
- 1 Table of Contents
- 2 Before Installation
- 3 Selecting Installation Site
- 4 Preparations before Installation
- 5 Installation Procedures for Fresh Air Intake Duct Connection
- 6 Indoor Unit Installation
- 7 Refrigerant Piping Work
- 8 Drain Piping Work
- 9 Electric Wiring Work
- 10 Wiring Example and How to Set the Remote Controller
- 11 Wiring Example
- 12 Field Setting
- 13 Installation of the Decoration Panel
- 14 Test Operation
- 15 Wiring Diagram
- Download this manual
See also:
Operating Manual
Advertisement
Table of Contents
Related Manuals for Daikin FHYCP71B8V1
Summary of Contents for Daikin FHYCP71B8V1
- Page 1 INSTALLATION MANUAL Split System air conditioners FHYCP71B8V1 FHYCP100B8V1 FHYCP125B8V1 FCQ35B8V1 FCQ50B8V1 FCQ60B8V1 FCQ71B8V3B FCQ100B8V3B FCQ125B8V3B...
- Page 2 ≥1500 ≥1500 ≤ 35 ≤ 35 ≤300 mm 1~1.5 mm...
- Page 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3...
- Page 4 3PW25005-5...
-
Page 5: Table Of Contents
OTHER DAMAGE TO THE EQUIPMENT. BE SURE ONLY 1 pc. 1 pc. 1 pc. TO USE ACCESSORIES MADE BY DAIKIN WHICH ARE SPECIFICALLY DESIGNED FOR USE WITH THE EQUIPMENT AND HAVE THEM INSTALLED BY A PROFESSIONAL. IF UNSURE OF INSTALLATION PROCEDURES OR USE,... -
Page 6: Selecting Installation Site
For the following items, take special care during Ceiling height construction and check after installation is finished This indoor unit may be installed on ceilings up to 3.5 m in height (for 80~125 units: 4.2 m). However, it becomes necessary to make field settings using the remote controller when installing Tick the unit at a height over 2.7 m (for 80~125 units: 3.2 m). -
Page 7: Installation Procedures For Fresh Air Intake Duct Connection
All the above parts are field supplied. Centre of the unit For other installation than standard installation, Screws (supplied with the unit) contact your Daikin dealer for details. Adjust the height of the unit until it matches the indication in figure NSTALLATION PROCEDURES FOR FRESH AIR Adjust the unit to the right position for installation. -
Page 8: Refrigerant Piping Work
If the refrigerant gas leaks during the work, ventilate the area. A EFRIGERANT PIPING WORK toxic gas is emitted by the refrigerant gas being exposed to a fire. For refrigerant piping of outdoor unit, refer to the installation manual supplied with the outdoor unit. Finally make sure there is no refrigerant gas leak. -
Page 9: Electric Wiring Work
After the piping work is finished, check if drainage flows Power supply terminal board (1) smoothly. Open the water inlet lid, add approximately 2 l of water gradually and check the drainage flow. Method of adding water (See figure 13) Portable pump Drain pipe Service cover... -
Page 10: Wiring Example
After connection IRING EXAMPLE Attach the small sealing (supplied with the unit) around the cables to prevent infiltrating of water from the outside into the For the wiring of outdoor units, refer to the installation manual unit. If two or more cables are used, divide the small sealing into attached to the outdoor units. -
Page 11: Field Setting
IELD SETTING FIRST SECOND Setting Mode No. CODE No. CODE No. Field setting must be made from the remote controller in accordance Pair system (1 unit) with the installation condition. Simultaneous Setting can be made by changing the "Mode number", "FIRST operation system (2-unit) CODE No."... -
Page 12: Installation Of The Decoration Panel
Computerised control (forced off and on/off operation) EST OPERATION Wire specifications and how to perform wiring Refer to "For the following items, take special care during Connect the input wire (option) to connector X40A on the construction and check after installation is finished" on page indoor PCB. -
Page 13: Wiring Diagram
IRING DIAGRAM : FIELD WIRING : BLACK : TERMINAL : RED : CONNECTOR : WHITE : WIRE CLAMP : YELLOW : PROTECTIVE EARTH (SCREW) 33H ......FLOAT SWITCH WIRED REMOTE CONTROLLER A1P......PRINTED CIRCUIT BOARD SS1 ..... SELECTOR SWITCH (MAIN/SUB) C1R .....CAPACITOR (FAN MOTOR) CD .......CURRENT DETECT CIRCUIT RECEIVER/DISPLAY UNIT (ATTACHED TO WIRELESS REMOTE CONTROLLER) - Page 14 Zandvoordestraat 300, B-8400 Oostende, Belgium 4PW23696-1...