Standard Accessories; Optional Accessories; Battery Removal/Installation - Hitachi WH 14DSAL Handling Instructions Manual

English

STANDARD ACCESSORIES

In addition to the main unit (1), the package contains the accessories listed in the
table below.
1 Charger (UC18YRSL or UC18YGSL) .......................... 1
2 Battery (BSL1830 or BSL1815X) ................................. 2
WH18DSAL
3 Plastic case .................................................................. 1
4 Battery cover ................................................................ 1
1 Charger (UC18YRSL or UC18YGSL) .......................... 1
2 Battery (BSL1430 or BSL1415X) ................................. 2
WH14DSAL
3 Plastic case .................................................................. 1
4 Battery cover ................................................................ 1
Standard accessories are subject to change without notice.

OPTIONAL ACCESSORIES

(Sold separately)
1. Battery
(BSL1430) (BSL1415X)
Optional accessories are subject to change without notice.
Before
The
charging
pilot lamp
lights or
blinks in red. While
charging
Charging
complete
Charging
impossible
The pilot Overheat
lamp lights standby
in green.
(2) Regarding the temperatures of the rechargeable battery
The temperatures for rechargeable batteries are as shown in Table 2, and batteries
that have become hot should be cooled for a while before being recharged.
Table 2 Recharging ranges of batteries
Rechargeable batteries
BSL1430, BSL1415X, BSL1830,
BSL1815X
7
(BSL1830) (BSL1815X)
Indications of the pilot lamp
Lights for 0.5 seconds. Does not light for 0.5 seconds. (off for
Blinks
0.5 seconds)
Lights
Lights continuously
Lights for 0.5 seconds. Does not light for 0.5 seconds. (off for
Blinks
0.5 seconds)
Flickers Lights for 0.1 seconds. Does not light for 0.1 seconds. (off for
0.1 seconds)
Lights continuously
Lights
Temperatures at which the
battery can be recharged
0°C – 50°C
APPLICATION
Driving and removing of machine screws, wood screws, tapping screws,
etc.

BATTERY REMOVAL/INSTALLATION

1. Battery removal
Hold the handle tightly and push the battery latch to remove the battery (see
Fig. 2).
CAUTION:
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (see Fig. 2).
CHARGING
Before using the power tool, charge the battery as follows.
<UC18YRSL>
1. Connect the charger's power cord to a receptacle.
When the power cord is connected, the charger's pilot lamp will blink in red.
(At 1-second intervals)
2. Insert the battery into the charger.
Firmly insert the battery into the charger until the line is visible, as shown in
Fig. 3, 4 .
3. Charging
When inserting a battery in the charger, charging will commence and the
pilot lamp will light continuously in red.
When the battery becomes fully recharged, the pilot lamp will blink in red.
(At 1-second intervals) (See Table 1)
(1) Pilot lamp indication
The indications of the pilot lamp will be as shown in Table 1, according to
the condition of the charger or the rechargeable battery.
Table 1
(3) Regarding recharging time
Depending on the combination of the charger and batteries, the charging
time will become as shown in Table 3.
Table 3 Charging time (At 20°C)
Charger
Battery
BSL1430, BSL1830
BSL1415X, BSL1815X
Malfunction in the battery or the
charger
Battery overheated. Unable to
charge (Charging will commence
when battery cools).
UC18YRSL UC18YGSL
Approx. 45 min. Approx. 90 min.
Approx. 20 min. Approx. 40 min.