Rear Panel - Numark cdmix usb User Manual

25. USB – You can connect USB thumb drives (with a FAT16 or FAT32 file system) with MP3s here. To view their
contents, use the SOURCE button and TRACK SELECT knob to select "USB A" or "USB B" as your source.
(Both decks can play tracks from the same USB device simultaneously.)
26. CHANNEL GAIN – Adjusts the channel's pre-fader and pre-EQ gain level.
27. CHANNEL TREBLE – Adjusts the high (treble) frequencies of the corresponding channel.
28. CHANNEL MID – Adjusts the mid-range frequencies of the corresponding channel.
29. CHANNEL BASS – Adjusts the low (bass) frequencies of the corresponding channel.
30. CHANNEL FADER – Adjusts the audio level on the corresponding channel.
31. CHANNEL CUE – Sends pre-fader audio to the Cue Channel for headphone monitoring.
32. CUE MIX – Turn to mix between Cue and Program in the Headphone channel. When all the way to the left,
only channels routed to CUE will be heard. When all the way right, only the Program mix will be heard.
33. CUE GAIN – Adjusts the volume for headphone cueing.
34. HEADPHONES – Connect your 1/4" or 1/8" headphones to
this output for cueing and mix monitoring.
35. MIC ON / OFF – Mutes and unmutes the microphone signal.
When muted, the microphone signal will not be routed to the
Master mix.
36. CROSSFADER – Blends audio playing between Channels 1 and 2. Slide this to the left to play Channel 1 and
slide to the right to play Channel 2.
Note: The crossfader is user replaceable. Simply unscrew the screws which hold it in place, lift it out and
disconnect the cable. Re-attach the new crossfader and screw the mounting plate back onto the unit. Test
and confirm new crossfader is working as intended.
37. STEREO LEVEL INDICATOR – Displays the audio level of the Program mix.
38. MASTER VOLUME – Adjusts the output volume of the Program mix.
39. MONO / STEREO – Adjusts the Program mix for stereo or mono operation.
40. MIC 2/AUX (2 way toggle switch) – Selects Mic 2 or Auxiliary input for this channel.

Rear Panel

1. POWER CONNECTOR – Connect the supplied power cable here.
2. POWER SWITCH – Turns the machine on and off. The unit should always be shut down with this switch first
before any external power is removed.
3. AUX INPUT (RCA) – Connect an additional line-level audio source to this input. To route the AUX signal to the
mix, you will need to flip the AUX channel's input selector (located on the top panel) to "AUX."
4. MIC 1 INPUT – Connect a microphone to this input with an XLR
or 1/4" cable.
5. MIC 2 INPUT – Connect a 1/4" microphone to this input if you
would like to use an additional microphone on the Aux channel.
To route the MIC2 signal to the mix, flip the AUX channel's INPUT
SELECTOR (located on the top panel) to "MIC."
6. MASTER OUTPUT (XLR) – Connect this low-impedance XLR output to a PA system or powered monitors.
Control the level of this output with the MASTER fader on the top panel.
7. MASTER OUTPUT (RCA) – Use standard RCA cables to connect this output to a speaker or amplifier system.
Control the level of this output by using the MASTER knob on the top panel.
8. USB JACK –
You can connect USB thumb drives (with a FAT16 or FAT32 file system) with MP3s here. To
view their contents, use the SOURCE button and TRACK SELECT knob to select "USB A" or "USB B" as your
source. (Both decks can play tracks from the same USB device simultaneously.)
7
6 3
Note: When connecting microphones,
make sure the mic channel's gain knob is
at the lowest setting before connecting it.
5
8
4
6
2
Note: When connecting microphones,
make sure the mic channel's gain
knob is at the lowest setting.
1