Control Elements; Charging Battery; Led; Troubleshooting - Silvercrest SBL 3.0 A1 User Manual And Service Information

such cases, the device should not be used
AUX operation
until it has been inspected by authorised
Pairing mode
service personnel. Only have the device
repaired by qualified personnel. Never
Bluetooth
open the housing of the device. Only use
operation
a clean, dry cloth for cleaning and never
Battery is
use any corrosive liquids. To remove
charging
stubborn dirt use a slightly moistened
Battery low
cloth and a mild cleaning agent. Never
try to open the housing of the device as
First use
this would void your warranty.
Before using for the first time, remove the

Control elements

film from the bottom of the loudspeaker.
Charging the battery
Before the first use or when the built-in
battery is empty, you charge it as follows:
 Set the mode selection switch (4) to
"OFF".
 Connect the micro USB to USB cable to
the micro USB socket (5) and a free
USB socket of your computer when it is
switched on or a USB power supply
(not supplied).
 The LED (3) lights up orange while the
battery is being charged and goes out
when the battery is fully charged.
Never cover the device while it is
charging, as it can become heated.
1 Loudspeaker
AUX operation
2 Microphone
 Set the volume of your audio source to
3

LED

a low level.
4 Mode selection switch
 Set the mode selection switch (4) to
5 Micro USB socket (at the back)
"AUX".
 Connect the micro USB to 3.5mm jack
6 Multifunction button
cable to the micro USB socket (5) and
the 3.5mm jack plug to an external
LED
audio source.
 Adjust the volume on the external
Refer to the table below for the different
audio source. In this mode the
statuses of the LED (3):
multifunction button is disabled.
®
Bluetooth operation
Lights up green
®
Flashes alternately Bluetooth operation enables wireless
hands-free operation of mobile phones,
orange/blue
for example. This loudspeaker allows you
®
Flashes blue every
to use a Bluetooth
5 seconds
range of Bluetooth
Lights up orange
to approx. 10 metres. If your playback
device supports the Bluetooth
Flashes orange
A2DP, you can also transfer music
wirelessly to your loudspeaker. To be
able to remotely control the playback
device with the loudspeaker, it must also
support the AVRCP profile.
Depending on the manufacturer, model
and software version of the mobile phone
or playback device which is used, the
complete functionality of the loudspeaker
cannot be guaranteed in all cases.
Proceed as follows to connect the
loudspeaker with your mobile phone:
 Set the mode selection switch (4) to
„ ".
 The LED (3) now flashes blue a few
times. Wait until the LED (3) flashes
alternately blue/orange.
 Now connect your mobile phone with
the loudspeaker via Bluetooth
further details,
instructions of your mobile phone.
Select the device "SBL 3.0 A1" from the
list of devices which are found and
establish the connection. If you are
asked for a PIN, enter "0000".
 The loudspeaker confirms this with a
dual tone and the LED (3) flashes blue
approximately every 5 seconds as
soon as the connection has been
established.
The multifunction button (6) has the
following functions:
Turn briefly: Previous title
Turn for a longer
period:
Volume down
®
enabled device. The
Press briefly: Play/Pause
®
operation is restricted
or accept a call or terminate
dialling or the connection,
®
profile
Press twice: Redial,
Press for 2 seconds:
Reject calls
Turn briefly:
Next title
Turn for a longer
period:
Volume up
Environmental information
The product bears the symbol
of a crossed-out wheelie bin. It
is therefore subject to the
European Directive 2012/19/EU.
All old electrical and electronic devices
must be separated
household waste and disposed of at
designated state facilities. For further
®
. For information contact your local authorities,
waste disposal office or the shop where
please read the
you bought the device.
The built-in battery cannot be removed for
disposal.
Conformity information
This device meets the basic
requirements
relevant regulations of the EMC Directive
2004/108/EC, the
Directive 2006/95/EC,
Directive 1999/5/EC and the RoHS
Directive 2011/65/EU.
full conformity declaration
downloaded from www.lidl-service.com.

Troubleshooting

The loudspeaker cannot
switched on.

Charge the battery.
®
The Bluetooth connection is not
established.

Set the mode selection switch (4) to
„ ".

The distance between the devices is
too large, reduce it.
The speaker is buzzing while
charging.

Set the mode selection switch (4) to
"OFF" or use the supplied micro USB
to USB cable for charging.

Warranty

Warranty of TARGA GmbH
This device is sold with three years
warranty from the date of purchase.
from normal
Please keep the original receipt in a safe
place as proof of purchase. Before using
your product for the first time, please read
the enclosed documentation. Should any
problems arise which cannot be solved in
this way, please call our hotline. Please
have the article number and, if available,
the serial number to hand for all
enquiries. If it is not possible to solve the
problem on the phone, our hotline
support staff will initiate further servicing
procedures depending on the fault.
and other
Within the warranty period the product
will be repaired or replaced free of
Low Voltage
charge as we deem appropriate. No new
the R&TTE
warranty period commences if the
product is repaired or replaced.
The
Consumables such as
can be rechargeable batteries and lamps are not
covered by the warranty.
Your statutory rights towards the seller
are not affected or restricted by this
warranty.
be
Service
Phone: 0207 – 36 50 744
E-Mail:
service.GB@targa-online.com
Phone: 01 – 242 15 83
E-Mail:
service.IE@targa-online.com
Phone: 800 – 62 175
E-Mail:
service.MT@targa-online.com
Phone: 800 – 92 496
E-Mail:
service.CY@targa-online.com
IAN: 101438
Manufacturer
TARGA GmbH
Coesterweg 45
59494 SOEST
GERMANY
batteries,