Summary of Contents for Nilfisk-ALTO FLOORTEC R 580 B
Page 1
www.nilfisk-alto.com FLOORTEC R 580 B DEUTSCH BETRIEBSANLEITUNG FRANÇAIS MANUEL D’UTILISATION ENGLISH USER MANUAL NEDERLANDS GEBRUIKSAANWIJZING...
SPARE PARTS AND MAINTENANCE All necessary operating, maintenance and repair procedures must be carried out by qualified personnel or by Nilfisk-Alto Service Centers (listed at the end of this manual). Only original spare parts and accessories must be used. Call Nilfisk-Alto for service or to order spare parts and accessories, specifying the machine model and serial number.
This machine cannot be used on public roads. – Do not tamper with the machine safety guards and follow the ordinary maintenance instructions scrupulously. – Do not remove or modify the plates affixed to the machine by the Manufacturer. FLOORTEC R 580 B ENGLISH...
Spare Parts List – No. 1 main fuse (F0) 150A – Battery connector FLOORTEC R 580 B MACHINE DESCRIPTION OPERATION CAPABILITIES The sweeper is used to sweep dust or light debris on smooth and solid floor, in civil or industrial environment, under safe operation conditions by a qualified Operator.
Battery total voltage Usable battery capacity Battery case dimensions Battery compartment max. size Dust vacuuming and filtering Paper dust filter, 5-10 µm Main broom compartment vacuum FLOORTEC R 580 B ENGLISH Values 1,050 mm 1,310 mm 1,776 mm 1,207 mm...
SW12: Hopper closed position microswitch SW13: Filter-shaker switch SW14: Light switch (optional) SW15: Horn switch SW16: Working light switch (optional) SW17: Safety microswitch (in the seat) SW18: Accelerator pedal microswitch FLOORTEC R 580 B Colour code Black Blue Brown Green Grey...
For the battery choice and installation, apply to qualified battery retailers. 2. Install the batteries and set the battery type (WET or GEL) on the machine (see the following paragraph). 3. Charge the batteries (see the relevant procedure in the Maintenance chapter). FLOORTEC R 580 B ENGLISH...
If the machine has not been used yet after the transportation, check that each block and locking system used for the transportation, have been removed. FLOORTEC R 580 B STARTING AND STOPPING THE MACHINE Starting the machine Sit in the driver's seat (27, Fig. B) and, using the lever (23) adjust the seat to a comfortable position.
270 mm. To bring the hopper back to its original position (horizontal position), press the enabling switch (1, Fig. B) while pressing the hopper overturning switch (16. Fig. B). FLOORTEC R 580 B ENGLISH...
(3): replace hydraulic oil for the first time after 500 hours, then after 2,000 hours or every year. 146 2601 000(1)2005-03 A USER MANUAL Every 10 Every 50 On delivery hours hours ENGLISH Every 100 Every 200 Every 400 hours hours hours (*) (2) (*) (3) FLOORTEC R 580 B...
When the broom is too worn to be adjusted, replace it as shown in the next paragraph. FLOORTEC R 580 B 10. Engage the retainer (6, Fig. C) and close the left door (5).
Reinstall the new broom with the hub (2) on the machine after seating the key (4). Position the washer (5) and tighten the screw (1). Carry out the side broom height check and adjustment, as described in the previous paragraph. FLOORTEC R 580 B ENGLISH...
11. Install in the reverse order of removal (steps from 8 to NOTE When reinstalling the filter, the wire gauze (2, Fig. O) must be facing upward. FLOORTEC R 580 B CLOSED POCKET DUST FILTER CLEANING AND INTEGRITY CHECK NOTE...
(maximum level) marks shown in figure Y. If necessary, add hydraulic oil - viscosity grade 32 cSt - through the plug (1, Fig. Y). Disengage the support rod (16, Fig. V) and close the hood (1). FLOORTEC R 580 B ENGLISH...
10. Reconnect the battery connector (4, Fig. V) to the machine. 11. Disengage the support rod (16, Fig. V) and close the hood (13, Fig. C): the machine is ready to be used. FLOORTEC R 580 B SAFETY FUNCTIONS The machine is equipped with the following safety functions.
The filter-shaker does not work Check the fuse (F4, Fig. Z) integrity For further information, refer to the Service Manual, available at any Nilfisk-Alto Service Center. 146 2601 000(1)2005-03 A USER MANUAL SCRAPPING Have the machine scrapped by a qualified scrapper.