1. Manuals
  2. Brands
  3. Mitsubishi Electric Manuals
  4. Projector
  5. VS-50XL20U
  6. Setup and installation manual

Mitsubishi Electric VS-50XL20U Setup And Installation Manual

Hide thumbs Also See for VS-50XL20U:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Manual
TM
DLP
Projector
VS-50XL20U, VS-67XL20U,
VS-50XLW20U
Set-up and Installation Manual
October 10, 2003 (REV 1.4)

Advertisement

Table of Contents
loading

Related Manuals for Mitsubishi Electric VS-50XL20U

Summary of Contents for Mitsubishi Electric VS-50XL20U

  • Page 1 Projector VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual October 10, 2003 (REV 1.4)

  • Page 2: Table Of Contents

    Release the lock screws....................14 6-axis adjustment ......................15 1.4.4. 1.4.5. Adjusting procedure......................16 1.4.6. Fixing the adjuster ......................16 1.4.7. Mirror distortion adjustment (for VS-50XL20U and VS-50XLW20U) ......17 1.5. Initial set up .........................19 1.5.1. Menu operation ......................19 1.5.2. Dipswitch setting......................21 1.5.3. System set up.......................21 1.5.4.
  • Page 3 Action in manual lamp swap (for VS-50XLW20U) .............60 1.10.5. Lamp position auto calibration (for VS-50XLW20U) ..........60 1.10.6. Warning indication (for VS-50XLW20U) ..............61 1.11. Condenser lens adjustment (for VS-50XL20U and VS-67XL20U) ........62 1.12. Focus adjustment......................63 1.13. For delivery ........................64 1.13.1. 6-axis adjuster fixing ....................64 1.13.2.

  • Page 4: Set-Up And Installation

    1.6 Input memory setting (When the 1.7 Input memory setting (When the main unit input port is selected) input board is selected) 1.8 Display memory setting 1.9 Setting as daisy chain connection Finish VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...

  • Page 5: Installation

    Spring washer (for M6) Stepladder Joint hole seal Spacer Power cord (1.8m) (1mm thickness for North America and Europe for VS-50XL20U and VS-50XLW20U, (in VS-50XL20U and VS-67XL20U) 2mm thickness for VS-67XL20U) Control cable Wrench (for level adjuster) User’s manual Optional products...

  • Page 6: Input Board Installation (When Using Optional Input Board)

    1. Remove 2 hole-stoppers. Input board (VC-B20KV) Firmly attach the input board with the 6 screws that has been removed in the step 1 at the positions shown in the figure. Input board VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...

  • Page 7: Color Wheel Unlocking

    1.2.4. Color wheel unlocking Unlock the color wheel surely before turning on the main power switch. Also for VS-50XLW20U, detach the lamp cushion. Turning on without the unlocking or the detaching may cause damage. Make sure the key slot faces the top as you begin the procedure.

  • Page 8: Lamp Cushion Detaching (For Vs-50Xlw20U)

    Lamp cushion Lamp cover Caution Before shipment, be sure to insert the cushion (see chapter 1.13.3, on page 65). Shipping the product without inserting may cause breakage. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...

  • Page 9: Installation Procedure

    Allen wrench (5 mm) to remove the screen units from all projectors to be installed (this applies to model VS-50XL20U and VS-50XLW20U which are supplied with the screen fitted). Cube unit Open the lower door 90 degrees by pushing down the handles.
  • Page 10 VS-67XL20U, the screens were supplied (2mm) separately). Put the spacers between each screens and adjust the screen gaps to be 1 mm for VS-50XL20U/VS-50XLW20U or 2 mm for VS-67XL20U. Firmly tighten the 4 screen fixing screws. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...
  • Page 11 1.2.6.3. Fixing to the wall and floor You don’t have to attach the lower door in this chapter since the picture outline has yet to be adjusted as explained in the next chapter. After the picture outline adjustment, attach the door in the reverse order of 1.2.6.1. Attach floor fixing brackets to 4 corners of the level adjuster and fix them to the floor with the anchor bolts.

  • Page 12: Connecting

    (5 pcs) (In this case, it cannot be connected to a loop.) Video device Panel 1 Panel 2 Panel 3 Panel 4 Panel 5 Panel 6 External controller Supplied control cables (5 pcs) VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...
  • Page 13 1.3.3.2. In the case of other than daisy chain The multi-screen can be configured by connecting with matrix switch as well as daisy chain connection. External Supplied control cables Panel 1 Panel 2 Input 1 Matrix switch Input 2 Input 3 Input 4 Panel 4 Panel 3...

  • Page 14: Picture Outline Adjustment

    Before 6-axis adjustment, release the locks on the adjuster. Loosen the 4 locking screws by Allen wrench (2mm) and 5 fixing screws in the adjuster by Allen wrench (4mm). 4 lock screws 5 fixing screws VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...

  • Page 15: 6-Axis Adjustment

    1.4.4. 6-axis adjustment A: H position B: V keystone C: Tilt D: V position F: Zoom E: H keystone View from the screen A: H position B: V keystone C: Tilt D: V position E: H keystone F: Zoom REV 1.4...

  • Page 16: Adjusting Procedure

    Before shipment, in addition to above, be sure to fix the 4 lock screws of the adjuster and perform the color wheel locking. Also for VS-50XLW20U, be sure to insert the lamp cushion (see chapter 1.13, on page 64). VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...

  • Page 17: Mirror Distortion Adjustment (For Vs-50Xl20U And Vs-50Xlw20U)

    1.4.7. Mirror distortion adjustment (for VS-50XL20U and VS-50XLW20U) 1.4.7.1. Parallelogram distortion correction If a parallelogram distortion that cannot be corrected by 6-axis adjuster appears, correct it according to the following procedure. Allign top, bottom and right lines of the crosshatch pattern with the screen edge by 6-axis adjuster.
  • Page 18 2. Loosen the fixing screw and then turn the adjustment screw clockwise until distortion is corrected. 2. Adjustment screw 3. After the adjustment, tighten the fixing screw. 4. After the adjustment, fix the 6-axis adjuster (chapter 1.4.6, on page 16). VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...

  • Page 19: Initial Set Up

    1.5. Initial set up 1.5.1. Menu operation 1.5.1.1. Control button list In normal mode In advanced mode Remote In stand- Menu OFF Menu OFF Menu ON control by state Test pattern Test pattern Test pattern Test pattern Test pattern Test pattern POWER ON Turn on －...
  • Page 20 For instance, if the set ID is one, input 01. It can be also selected by left/right button after the [FUNC] button. The projector other than designated ID will ignore the remote control. Pressing 00 after [FUNC] button enables remote control of all projectors regardless of the remote ID setting. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...

  • Page 21: Dipswitch Setting

    1.5.2. Dipswitch setting Before turning on the main power switch, set the dipswitch correctly according to the system configuration. Be sure to turn off the main power switch if you change the setting in the middle of the operation. Only turning on the main power switch will renew the setting. Initial Name Function...
  • Page 22 In the case of a single screen or a multi-screen without the input board, normally set OFF since blurred small characters may annoy you. Also set OFF when the picture outline is adjusted without overlapping. [Procedure] Select OVERLAP in MISC FUNCTION in the system menu. Set ON or OFF. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...
  • Page 23 1.5.3.7. OFFSET (When the input board is selected) This adjustment is normally unnecessary. Used to finely adjust the horizontal/vertical position and size if the picture outline is shifted after the final 6-axis adjustment. [Procedure] Select OFFSET in MISC FUNCTION in the system menu. H.POSITION: to adjust horizontal position.
  • Page 24 BLOWOUT (chapter 1.5.3.13, on page 25) is set OPERATE. • LED： Blinking the blue LED on screen. • OFF： No indication. [Procedure] Select BLOWOUT in INDICATION in MISC FUNCTION in the system menu. Set LED or OFF. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...
  • Page 25 1.5.3.12. AUTO POWER ON Used to set automatic turning on when the main power is supplied. The initial setting is OFF. • ON： Automatic turning on when the main power is supplied. • OFF： When the main power is supplied, the projector uses the last memory status. For instance, it becomes stand-by state if the main power was turned off in stand-by state.

  • Page 26: Color Balance Adjustment

    Adjust the tint on the monochrome red finely by increasing or decreasing R–G, R–B if the tint differs between each screen. Display the monochrome green and adjust the luminance level finely by decreasing G–G of VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...
  • Page 27 the brighter screen, according to the darkest screen, if the luminance differs between each screen. (If decreasing the luminance excessively, increase G–G.) Adjust the luminance level on the monochrome green finely by increasing or decreasing G–R, G–B, if the tint differs between each screen. Display the monochrome blue and adjust the luminance level finely by decreasing B–B of the brighter screen, according to the darkest screen, if the luminance differs between each screen.
  • Page 28 Select SET TARGET COLOR in TARGET COLOR in MAINTENANCE in the system menu. Press [ENTER] button in reply to “SET OK?” message. The set timer value (set operating time) is displayed to indicate when TARGET COLOR is set. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...
  • Page 29 1.5.4.7. SENSOR SENSOR RUN can automatically correct the luminance to achieve uniformity in a multi-screen connected by control cables when the lamp brightness changes. Set it after adjustment of the luminance and tint between screens. When SENSOR is set RUN, WHITE BOOST should be set OFF.

  • Page 30: Image Set Up

    Select AMP GAIN in INSTALLATION in the system menu. Select MANUAL GAIN. Adjust R/G/B-GAIN or R/G/B-LEVEL respectively. [NORMAL] button can reset it to the factory setting. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...
  • Page 31 1.5.5.3. SCALER AMP GAIN (When S.ANALOG is input) This adjustment is normally unnecessary. Used to adjust the gain of analog signal input level in input board as needed. It is available toward all input memories. [Procedure] Display full-white video signal via actual input route. Select SCALER AMP GAIN in INSTALLATION in the system menu.
  • Page 32 If there is something wrong with the total quality when you display the contents that end users actually show in a multi-screen, select all white boost setting OFF. Also, if you cannot identify the end users’ final contents, select it OFF. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...

  • Page 33: Input Memory Setting (When The Main Unit Input Port Is Selected)

    1.6. Input memory setting (When the main unit input port is selected) Be careful that the menu, when the main unit input is selected, is different from the one when the input board (VC-B20KA, VC-B20KV) is selected. 1.6.1. Selecting input port Input port can be selected while any menus or test patterns are INPUT PORT not displayed.

  • Page 34: Signal Adjustment

    While 5-line (separate sync) or 4-line (composite sync) signal is input with sync on green, the clamp pulse on the green channel cannot be adjusted. In this case, follow the procedure below to set sync on green. [Procedure] Select SYNC SELECT in the menu 1. Select SOG. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...
  • Page 35 1.6.3.5. CLOCK RANGE (When ANALOG is input) This adjustment is normally unnecessary since optimum value is automatically selected when H.TOTAL is changed. If the jitter noise cannot be improved by H.TOTAL and FINE adjustment, CLOCK RANGE fine adjustment may improve it. [Procedure] Select CLOCK RANGE in the menu 1.

  • Page 36: Image Quality Adjustment

    “1” makes it smooth. Setting “0” sharpens the displays, especially in the scaled down images. The initial setting is 1. [Procedure] Select SCALING FILTER in the menu 1. Adjust the value by left/right buttons. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...

  • Page 37: Input Memory Saving

    1.6.5. Input memory saving The adjusted values can be saved in the input memory. The number of memories is 128. Note: Be sure to save newly adjusted signal even if the same resolution signal already exists in the memory. If the FINE or POSITION, etc. settings are different from it, save the signal in another input memory number.

  • Page 38: Input Memory Setting (When The Input Board Is Selected)

    [NORMAL] button is pressed. Also in the case that incorrect image is displayed, press [NORMAL] button again to reselect other candidates. If the signal does not match, the following items in the menu 1 have to be adjusted. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...
  • Page 39 1.7.3.1. SIGNAL SELECT (When COMPOSITE or Y/C is input) Adjust it when incorrect image is displayed after automatic SIGNAL SELECT input signal scanning. AUTO It can designate the input signal type that already exists in the NTSC default memory. [Procedure] SECAM NTSC4.43 Select SIGNAL SELECT in the menu 1 (page 1).

  • Page 40: Signal Adjustment

    Adjust the vertical size of input signal. Note: If H.SIZE or V.SIZE is changed, H.DISPLAY POS and V.DISPLAY POS in the menu 2 should be readjusted to 1/1 （chapter 1.7.2, on page 38）. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...
  • Page 41 1.7.4.3. FRAME LOCK This adjustment is normally unnecessary since it is automatically set in automatic input signal scanning. Used to select frame lock setting when frame tearing or field skips are noticeable in a moving image. Set ON when input signal is a moving image and has 50 – 60 Hz of the vertical scanning frequency.
  • Page 42 • HD/VD： Select when 5-line signal is input. • SOG： Select when sync on green signal is input. [Procedure] Select SYNC SELECT in the menu 1 (page 4). Select AUTO, HD/VD or SOG. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...
  • Page 43 1.7.4.9. CLOCK RANGE (When S.ANALOG is input) This adjustment is normally unnecessary since the optimum value is automatically selected when H.TOTAL is changed. Used to set the dot clock frequency of input signal. The displayed numbers and corresponding dot clock frequencies are shown in fallowing tables. [Procedure] Select CLOCK RANGE in the menu 1 (page 4).

  • Page 44: Image Quality Adjustment

    : The image is displayed at the aspect ratio of 5:4. • 16:9 : The image is displayed at the aspect ratio of 16:9. [Procedure] Select ASPECT-RATIO in the menu 1 (page 2). Select 4:3, 5:4 or 16:9. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...
  • Page 45 1.7.5.6. SCALING FILTER Used to set the scaling filter in the input board signal. If jagged character outlines are noticeable, setting “1” or “2” makes it smooth. “2” makes softer image. Setting “0” sharpens the displays, especially when displaying high resolution image such as UXGA signal or scaled down images. The initial setting is 1.

  • Page 46: Input Memory Registration

    • Delete: Press [MEM LIST] button and select INPUT MEMORY. Designate the memory number to delete by left/right buttons and press [ENTER] button. Select DELETE MEMORY by up/down buttons and press [ENTER] button. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...

  • Page 47: Display Memory Setting

    1.8. Display memory setting Used to set the output image on screen when it is used as a multi-screen or the display position of the output image requires some adjustments. There is no need to register the display memory when the input board is not attached. In this case, the menu 2 for the memory setting up is not displayed.

  • Page 48: Display

    1 – 128 are reflected on the output signal. [Procedure] Select DIGITAL OUT in DISPLAY in the menu 2. Select the signal to be output from digital output terminal. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...

  • Page 49: Screen Mode

    1.8.6. SCREEN MODE Used to set the screen mode when a signal with other than 4:3 aspect ratio, as HDTV or SXGA signal, is input. If it has the 4:3 aspect ratio, the displaying doesn’t change. • NORMAL: The original aspect ratio is maintained and the whole image is displayed at the center of the screen.

  • Page 50: Setting As Daisy Chain Connection

    Normally it is unnecessary to change the input signal position since it is automatically set by automatic input signal scanning (chapter 1.7.3, on page 38). Make certain that same images are displayed on each screen as following example. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...
  • Page 51 Set the position and expansion ratio (“1.8.2 H.DISPLAY POS, V.DISPLAY POS” on page47) again to fit the system in reference to the following setting sample in left side. Check the displaying to be as the example in right side. H=1/2 H=2/2 V=1/2 V=1/2...

  • Page 52: Lamp Replacement

    “1.”. Be sure to use optional lamp specified for the product. The part number of the lamp used in VS-50XL20U and VS-67XL20U is S-XL20LA. The part number of the lamp used in VS-50XLW20U is S-XH20LA.

  • Page 53: Procedure

    1.10.2. Procedure 1.10.2.1. For VS-50XL20U and VS-67XL20U Turn off the main power switch and unplug the power cord from the wall outlet. • Wait at least one hour for the lamp cooling down. Hold the handles by the fingers and pull the lower door open.
  • Page 54 If TERGET COLOR (chapter 1.5.4.6, on page 28) is set, the optimum color is adjusted automatically after lamp replacement. • If SENSOR (chapter 1.5.4.7, on page 29) is set RUN, the brightness is automatically adjusted to be uniform across a multi-screen. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...
  • Page 55 1.10.2.2. For VS-50XLW20U Turn off the main power switch and unplug the power cord from the wall outlet. • Wait at least one hour for the lamp cooling down. Loosen the screw in upper door to open. Upper door Screw Lift up the latch in the partition door.
  • Page 56 If you replace the lamp in lighting position, perform manual lamp swap in the state of the lamp cover closing. • Do not touch the glass envelope of the lamp. It may burn you. Manual lamp swap Replacing lamp switch Lamp waiting position Lamp lighting position VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...
  • Page 57 Insert a new lamp with correct direction to the end. • Insufficient inserting may cause damage. • Do not touch the glass envelope of the lamp with your fingers. The oil on your fingers may cause damage or explosion of the lamp. Lamp waiting position New lamp...
  • Page 58 If TERGET COLOR (chapter 1.5.4.6, on page 28) is set, the optimum color is adjusted automatically after lamp replacement. • If SENSOR (chapter 1.5.4.7, on page 29) is set RUN, the brightness is automatically adjusted to be uniform across a multi-screen. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...

  • Page 59: Auto-Lamp Changing Function (For Vs-50Xlw20U)

    1.10.3. Auto-lamp changing function (for VS-50XLW20U) VS-50XLW20U is equipped with auto-lamp changing function that can detect the lamp failure or brightness deterioration and then swaps it for spare lamp automatically. The lamp is managed as three types of status, “NEW”, “USED” and “JUNK”. It is displayed on screen by [DISPLAY] button.

  • Page 60: Action In Manual Lamp Swap (For Vs-50Xlw20U)

    5 minutes after the auto-lamp changing. If you turn on the power to ignite the same lamp, the auto calibration will not be performed since the lamp position is automatically set according to the memorized result. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...

  • Page 61: Warning Indication (For Vs-50Xlw20U)

    1.10.6. Warning indication (for VS-50XLW20U) You can indicate the warning mark to induce to replace the spare lamp and the pre-announcement of auto-lamp changing on screen. It can be set in WARNING menu in INDICATION in the system menu (chapter 1.5.3.11, on page 24). [Warning mark to induce to replace the spare lamp] “☀”...

  • Page 62: Condenser Lens Adjustment (For Vs-50Xl20U And Vs-67Xl20U)

    1.11. Condenser lens adjustment (for VS-50XL20U and VS-67XL20U) When the brightness is low after lamp replacement, the brightness may increase if you adjust the position of the condenser lens. You don’t have to adjust it at initial setting since the position has been adjusted optimally with built-in lamp at factory.

  • Page 63: Focus Adjustment

    1.12. Focus adjustment This adjustment is normally unnecessary. You can adjust the lens focus when it is soft. [Procedure] Display the crosshatch pattern by pressing [TEST] button twice. Open the lower door and rear panel in the rear of the projector. Detach the band that fixes the lens and accordion hose.

  • Page 64: For Delivery

    Push the color wheel cushion all the way in till the flange of it touches the die cast holder. Flange Die cast holder VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...

  • Page 65: Lamp Cushion Inserting (For Vs-50Xlw20U)

    1.13.3. Lamp cushion inserting (for VS-50XLW20U) Before shipment, be sure to insert the lamp cushion into the designated place. Shipping the product without inserting may cause breakage. • Be care about inserting direction of the cushion. • It should be remembered to lock the lamp cover after inserting. If you neglect to lock it, it may cause damage.

  • Page 66: Function

    OFF, 1, 2, 3, 4 (OFF) Edge enhancement setting 36, 44 ASPECT-RATIO – 4:3, 5:4, 16:9 Aspect ratio setting (*1) SCALING FILTER 0, 1 (1) 0, 1, 2 (1) Scaling filter setting 36, 45 VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...

  • Page 67: Menu 2 (Short Press)

    2.2.1.2. Additional items (When ANALOG or S.ANALOG is selected) Item In main unit In input board Description Page H.TOTAL 700 – 1900 700 – 2300 Sampling number setting 34, 39 FINE -16 – 15 (0) -32 – 31 (0) Sampling phase setting 34, 41 CLAMP START 0 –...

  • Page 68: Menu 2 (Press-And-Hold)

    F-REDUCTION (F-REDUCTION) setting Termination setting TERMINATE 75, 1K (1K) (When main unit input) S.TERMINATE 75, 1K (1K) Termination setting (*1) ADV.COL ON, OFF (ON) Advanced color setting ADV.DARK ON, OFF (OFF) Advanced dark setting VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...

  • Page 69: Memlist

    (Continued) Item Description Page MISC GAMMA 1 – 5 (1) Gamma setting FUNCTION DITHER ON, OFF (ON) Dither setting 3D Y/C setting (When input 3D Y/C ON, OFF (ON) board, VC-B20KV is attached) Display memory at start-up START OFF, 1 – 256 (OFF) setting.

  • Page 70: Led Display

    * The real error number shows continuously. Ignore numbers that appear only briefly. * An error code many not indicate the primary cause. It may detect a secondary failure. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...

  • Page 71: Cleaning

    2.5. Cleaning Screen front surface Wipe with a lint free soft and dry cloth or with a damp cloth with water or alcohol. Do not use solvents including acid or alkali integrant or abrasive. Do not scrub hard with dry hard cloth. Cleaning the cabinet Wipe with a lint free soft and dry cloth or if necessary with a damp cloth.

  • Page 72: Terminal Functions

    IN/OUT port Input Output RCIN RCOUT Output Output TXDS2 TXDM2 Input Input RXDS2 RXDM2 Output Note: The CONTROL terminal pin assignment is different from conventional one. • CONTROL cable connection diagram VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...

  • Page 73: Supported Signal List (When The Input Board Is Selected)

    2.8. Supported signal list (When the input board is selected) RGB signal Computer/signal Resolution Line rate (kHz) Frame rate (Hz) IBM PC/AT compatible 640 x 400 37.9 84.1 640 x 400 31.5 70.1 640 x 400 37.9 85.1 640 x 480 31.5 60.0 640 x 480...
  • Page 74 The following signals are processed as follows: *3: The signal undergoes under sampling at the specified resolution. *4: The signal is displayed with over scan. *5: This signal isn’t supported when it is supplied to the DIGITAL IN connector. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...

  • Page 75: About Trademarks

    3. About trademarks (Digital Light Processing ) and DMD (Digital Micromirror Device ) are registered trademarks of Texas Instruments. ® ® ® Microsoft , Windows and Windows NT are registered trademarks of Microsoft Corporation. The names of other products or companies mentioned are registered trademarks or corporate trademarks of the companies written herein.

  • Page 76: Revision Archive

    • Move “Connecting” to chapter 1.3. (REV 1.4) • In chapter 1.5.4.1, the value in WHITE BALANCE was “MIDDLE”. • In chapter 2.2.1.1, the range of H.SIZE and V.SIZE were “640 – 1920” and “350 – 1200”. VS-50XL20U, VS-67XL20U, VS-50XLW20U Set-up and Installation Manual...

This manual is also suitable for:

Vs-67xl20uVs-50xlw20u

Table of Contents