1. Manuals
  2. Brands
  3. Clay Paky Manuals
  4. Speakers
  5. MYTHOS C61391
  6. Instruction manual

Clay Paky MYTHOS C61391 Instruction Manual

Hide thumbs Also See for MYTHOS C61391:
Table of Contents

Advertisement

Quick Links

Download this manual
INDEX
Page Contents
2
Safety Information
3
Unpacking and preparation
4
Installation and start-up
5
Control panel
7
Maintenance
13
Technical information
14
Cause and solution of problems
MYT OS
INSTRUCTION MANUAL
Congratulations on choosing a Clay Paky product
We thank you for your custom.
Please note that this product, as all the others in the rich Clay
Paky range, has been designed and made with total quality to
ensure excellent performance and best meet your expectations
and requirements.
1
C61391

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MYTHOS C61391 and is the answer not in the manual?

Questions and answers

Related Manuals for Clay Paky MYTHOS C61391

Summary of Contents for Clay Paky MYTHOS C61391

  • Page 1 MYT OS C61391 INSTRUCTION MANUAL INDEX Congratulations on choosing a Clay Paky product Page Contents We thank you for your custom. Please note that this product, as all the others in the rich Clay Safety Information Paky range, has been designed and made with total quality to...

  • Page 2: Safety Information

    SAFETY INFORMATION SAFETY INFORMATION IMPORTANT: Clay Paky recommends you carefully read and keep the safety information on this product, also http://www.claypaky.it/en available in digital format at the following link: Ref: [FIS00H – Safety Information Mythos - Supersharpy] INFORMAZIONI DI SICUREZZA...

  • Page 3: Unpacking And Preparation

    UNPACKING AND PREPARATION 2 x 183102/805 Packing contents - Fig. 1 UNLOCKED LOCKED LOCKED UNLOCKED PAN Mechanism Lock and Release (every 90°) - Fig. 2 TILT Mechanism Lock and Release (every 45°) - Fig. 3 MYT OS...

  • Page 4: Installation And Start-Up

    INSTALLATION AND START-UP Installing the projector - Fig. 4 WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/003 available on request). The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall. This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.

  • Page 5: Control Panel

    CONTROL PANEL Mains Connecting to the mains supply - Fig. 6 Connecting to the control signal line (DMX) - Fig. 7 Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified.
  • Page 6 Reversal of the display - Fig. 9 To activate this function, press UP and DOWN keys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again. Setting the projector starting address On each projector, the starting address must be set for the control signal (addresses from 1 to 512).

  • Page 7: Maintenance

    MAINTENANCE 1/4 Turn 1/4 Turn Locking and releasing Pan and Tilt movements - Refer to the instructions in the UNPACKING AND PREPARATION section. Opening the head covers - Fig. 10. Closing the head covers - Fig. 11. Continue MYT OS...
  • Page 8 • General cleaning of internal parts. • Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Clay Paky. • General visual check of the internal components, cabling, mechanical parts, etc.
  • Page 9 Cleaning of the filters - Fig. 13. Continue MYT OS...
  • Page 10 Lower Side remove the lamp contacts protection remove the fan unscrew a bit the 4 nuts to facilitate the lamp replacement pay attention to the right position of the lamp contacts (see pictures) 45° pay attention to the right position of the lamp contacts (see pictures) Lamp change - Fig 14.
  • Page 11 Rotating gobo wheel - Fig. 15. ATTENTION: - Before use custom gobos contact Clay Paky - The original gobos have a special coating designed specifically to resist to the high temperatures - The rotating gobo wheel only use dichroic glass gobos (it is not possible to use metal gobos) - For more information contact Clay Paky Static gobo wheel cod.
  • Page 12 Battery removal - Fig. 17 This product contains a rechargeable lithium iron tetraphosphate battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. LiFePO4 MYT OS...

  • Page 13: Technical Information

    TECHNICAL INFORMATION Lens IN&OUT 455 (17.91") Lens IN 408 (16.06") Lens OUT 427 (16.81") Lens IN 611 (24.05") (15.59") Lens OUT 628 (24.72") (22.44") (16.53") (14.96") Power supplies Noise level Effects section • 115/230V 50/60 Hz 50 dBA • 2 gobo wheels •...

  • Page 14: Cause And Solution Of Problems

    CAUSE AND SOLUTION OF PROBLEMS THE PROJECTOR WILL NOT SWITCH ON PROBLEMS ELECTRONICS NON-OPERATIONAL DEFECTIVE PROJECTION POSSIBLE CAUSES CHECKS AND REMEDIES REDUCED LUMINOSITY No mains supply. Check the power supply voltage. Lamp exhausted or defective. Replace the lamp. (See instructions). Signal transmission cable faulty or disconnected.
  • Page 15 CLAY PAKY - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035-654311 - Fax +39-035-301876 - www.claypaky.it S.p.A.

Table of Contents