Setup [Page 1; Setup [Page 2 - NEC HT1100 User Manual

The following buttons are not available for the currently projecting sig-
nals:
1) The Cut and Paste buttons on the Entry Edit Command screen
2) The Input Terminal button on the Entry Edit screen
NOTE: When all the signals in the Entry List are deleted, the currently projected
signal will be also deleted except locked signals.

Setup [Page 1]

Selecting Aspect Ratio and Position for Screen [Screen]
Screen Type:
Select one of three options: 4:3 Screen, 16:9 Screen or Anamorphic
for the screen to be used. See also "Aspect Ratio" on pages E-30
and E-31.
Position:
This feature adjusts the vertical position of the image when viewing
video with an aspect ratio selected.
When some aspect ratios are selected in Image, the image is dis-
played with black borders on the top and bottom.
You can adjust the vertical position between top and bottom.
Some DVI signals are available on one screen type only, but there
are some equipment with DVI output which is available on both 4:3
and 16:9. See page E-49 for supported signals.
NOTE: This option is available only when "16:9" is selected in Screen Type.
NOTE: During 3D Reform adjustment, "Screen Type" and "Screen Position" may
not be available. To make available, first reset the 3D Reform data and then do
settings again. Secondly repeat the 3D Reform adjustment. Changing "Screen
Type" and "Screen Position" can limit 3D Reform in its adjustable range.
Selecting Projector Orientation [Orientation]
This reorients your image for your type of projection. The options are:
desktop front projection, ceiling rear projection, desktop rear projection,
and ceiling front projection.
Setting Lamp Mode to Normal or Eco [Lamp Mode]
This feature enables you to select two brightness modes of the lamp:
Normal and Eco modes. The lamp life can be extended up to 3000 hours
by using the Eco mode.
Normal Mode . This is the default setting (100% Brightness).
Eco Mode ...... Select this mode to increase the lamp life (80% Bright-
ness).
Enabling Screen Trigger [Screen Trigger]
When "Screen Trigger" is selected and the projector is powered ON, the
screen trigger output sends a low voltage trigger to the screen control-
ler and the screen will go down. When the projector is powered OFF the
screen trigger stops sending a low voltage trigger to the screen control-
ler and the screen will go up. Use a commercially available stereo mini
cable.
Selecting a Color or Logo for Background [Background]
Use this feature to display a blue/ black screen or logo when no signal is
available. The default background is blue. You can change the logo screen
using the Viewer feature. See pages E-42.
Selecting Menu Language [Language]
You can choose one of 18 languages for on-screen instructions.
[Test Pattern]
Displays a test pattern for adjustment or setting.
Selecting this item will display the test pattern.
To turn off the test pattern, select a source such as Video, S-Video,
Component, Computer, DVI(DIGITAL) or Viewer.

Setup [Page 2]

Selecting Signal Format [Signal Select]
Computer:
Allows you to choose "RGB" for an RGB source such as a computer,
or "Component" for a component video source such as a DVD player.
Normally select "RGB/Component" and the projector automatically
detects an either incoming signal. However there may be some com-
ponent signals that the projector is unable to detect. If this is the
case, select "Component". Select "Scart" for the European Scart.
VIDEO and S-VIDEO:
This feature enables you to select composite video standards manu-
ally. Normally select "Auto". Select the video standard from the
pulldown menu. This must be done for Video and S-Video separately.
Selecting Standby Mode [Standby Mode]
The projector has two standby modes: Idle mode and Power-saving
mode.
Power-saving mode is the mode that allows you to put the projector in
the standby condition which consumes less power than the Idle mode.
The projector is preset for Idle mode at the factory.
NOTE: The HTTP server functions are not available during Power-saving mode.
Enabling High Speed Fan Mode [Fan Mode]
This option allows you to select two modes for fan speed: High speed
mode and Auto mode.
High speed .... The built-in fans run at a fixed high speed.
Auto ............... The built-in fans automatically run at a variable speed
according to the internal temperature.
When you wish to cool down the temperature inside the projector quickly,
select "High Speed".
NOTE: Select High speed mode if you continue to use the projector for consecu-
tive days.
Clearing Lamp Hour Meter [Lamp Hour]
Resets the lamp clock back to zero. Pressing this button appears a con-
firmation dialog box. To reset the lamp usage hour, press "OK".
NOTE: The projector will turn off and go into standby mode after 2100 hours (up
to 3100 hours in Eco mode) of service. In this condition you cannot clear the
lamp hour meter on the menu. If this happens, press the "HELP" button on the
remote control for ten seconds to reset the lamp clock back to zero. Do this only
after replacing the lamp.
E-33