Download
Share
Print this page
Ofna Racing X2 TRUGGY Instruction Manual
  1. Manuals
  2. Brands
  3. Ofna Racing Manuals
  4. Motorized Toy Car
  5. X2 TRUGGY
  6. Instruction manual

Ofna Racing X2 TRUGGY Instruction Manual

Hide thumbs

Advertisement

Quick Links

Download this manual

Advertisement

loading

Related Manuals for Ofna Racing X2 TRUGGY

Summary of Contents for Ofna Racing X2 TRUGGY

  • Page 2 THINGS REQUIRED FOR OPERATION OPTION THINGS NEED BESIDES THE KIT OPTION PART 3.5 cc (21 Class) ENGINE REAR EXHAUST OFNA/Picco Glow Plug Heat with Battery & Charger P7-EVO3 # 10227..$$19.95 (please note OFNA Glow Heats available) #51216 Bottle’s with spout # 10160 - large 500cc # 10161 - large 500 ccAuto Stop # 10162 - small 250cc...
  • Page 3 RTR KITS - REQUIRED FOR OPERATION You will need to buy a few items to start the engine and run the car. THINGS NEEDED • Use 20% nitro CAR fuel. Do not use airplane or heli fuels, they will over heat the engine. •...
  • Page 4 MUST READ THIS BEFORE RUNNING Running a nitro kit is fun and easy, but to make this a safe • Clean oil and dirt from chassis with a degreaser like Simple Green. and good experience you must observe a few rules. This kit is extremely fast, easily over 40MPH, and can seriously Precautions injure someone if you are not careful.
  • Page 5 PLASTIC PARTS USED 40538 40536 40533 DIFF. CASE FRONT C HUB FRONT AND REAR GEAR BOX 40668 FRONT AND REAR LOWER ARM 40669 30802 40643 BUMPER Throttle Linkage Plastic SHOCK PLASTIC PARTS 40643 Shock Cap Washer 40643 40643 Shock Plastic Shock Plastic Ball End Ball End...
  • Page 6 PLASTIC PARTS FOR USE 41034 41052 34026 CHASSIS BRACE SERVO SAVER SERVO FIXING PLASTIC PARTS 40540 40542 REAR UPPER RIGHT/FRONT BUMPER WIN STAY 41033 16015 40541 STONE GUARD WING RECEIVER BOX...
  • Page 7 ASSEMBLY OF THE FRONT AND REAR DIFF. NO.1 Builds two differentials for front and rear. Step 1 Step 2 40010 2.5x13.8mm Pin ..x4 40513 94034 40009 41031 4x4mm ..x2 Set Screw 36053 40538 40596 36053 40009 40010 P6 O-Ring 40596 ..x4 40010 40009...
  • Page 8 ASSEMBLY OF THE CENTER DIFF. NO.1 3x12mm Step 1 Step 2 Tighten 30774 30776 Tight the diff screws in this order. 4x10mm Washer ..x8 30776 40513 40011 94020 3x12mm Flat Head Hex Screw ..x4 30774 Alum. Cross Pin ..x4 Use 10000 weight diff. oil in the center.

  • Page 9: Table Of Contents

    ASSEMBLY OF THE FRONT SHOCK STAY NO.2 Step 2 Step 1 41009 3x10mm 41009 4x10mm 94003 3x10mm ..x4 41035 Hex Screw 40691 3x10mm 94009 41010 4x10mm ..x4 Hex Screw 3x10mm 41009 3x28mm ..x2 Cap Screw ASSEMBLY OF THE KNUCKLE ARMS 36053 NO.2 Assemble both right and left sides...
  • Page 10 ASSEMBLY OF THE FRONT UPPER ARMS NO.2 Assembly for both right and left side. 36850 Ball and Socket ..x2 11 ¡ G Approx. 9mm 41053 36861 36690 36850 ASSEMBLY OF THE FRONT STABILIZER NO.2 Assembly for both right and left side. Tighten 94041 40602...
  • Page 11 ASSEMBLY OF THE FRONT STABILIZER 3x3mm NO.2 3x3mm 94033 3x3mm ..x4 Set Screw 0.5mm 94035 3x8mm ..x4 Hex Screw 40533 3x8mm 40533 40685 3x3mm 3x8mm ASSEMBLY OF THE SERVO SAVER NO.4 40037 Step 1 Step 2 30776 40024 Do Not 40034 Over Tighten 40073...
  • Page 12 ASSEMBLY OF THE STEERING TIE-ROD NO.4 Assembly for both right and left side. Step 1 Step2 Tighten 40038 40039 3m Tapper Washer 36700 ..x2 40548 40548 Nylon Nut(Thin Type) ..x2 40039 40038 40660 40038 7mm Ball ..x4 3x16mm 36700 11 ¡ G 94021 66.5 mm 3x15mm...
  • Page 13 ASSEMBLY OF THE REAR UNIVERSAL 4x12mm NO.5 JOINT Step 1 Step 2 41035 5x4mm Set Screw ..x1 Tighten 5x4mm 4x12mm Hex Screw ..x4 41044 4x12mm 40689 ASSEMBLY OF THE REAR SHOCK NO.5 STAY Step 1 Step 2 41009 40542 41010 41009 3x10mm 3x10mm...
  • Page 14 ASSEMBLY OF THE REAR UNIVERSAL 4x12mm NO.5 JOINT Step 1 Step 2 41035 94036 5x4mm ..x1 Set Screw Tighten 5x4mm 94010 4x12mm ..x4 Hex Screw 41043 4x12mm 40689 ASSEMBLY OF THE REAR SHOCK NO.5 STAY Step 1 Step 2 41009 40542 41010 41009...

  • Page 15: 4X4Mm

    ASSEMBLY OF THE WING STAY NO.4 NO.5 Step 1 Step 2 94041 ..x2 Nylon Nut 4x20mm 94009 4x10mm ..x1 Hex Screw 4x10mm 94011 4x16mm ..x4 Hex Screw 41034 4x16mm 94012 4x20mm ..x1 Hex Screw ASSEMBLY OF THE REAR WHEEL HUBS NO.2 Assemble both right and left sides NO.5...
  • Page 16 ASSEMBLY OF THE REAR SUSPENSION ARMS 40540 NO.5 36850 40540 94041 40661 ..x4 Nylon Nut 36850 36850 7mm Ball ..x4 94005 3x16mm ..x2 Hex Screw 3x16mm 94008 3x25mm ..x2 Use this ball end on the wheel side.The left and right Hex Screw hand side are the same.
  • Page 17 ASSEMBL OF THE STONE GUARD AND BRACE NO.6 Assembly for both right and left side. NO.11 Step 1 Step 2 41042 41041 41035 41033 *Drill two 3mm holes for mounting ..x2 41035. 3x10mm 3x5mm 94018 3x5mm ..x2 Flat Head Hex Screw 3x10mm 94019 3x10mm...
  • Page 18 ASSEMBLY OF THE FRONT GEAR CASE ONTO CHASSIS NO.2 NO.4 94019 3x10mm ..x1 Flat Head Hex Screw 94039 4x10mm ..x2 Flat Head Hex Screw 94027 4x16mm ..x2 Flat Head Hex Screw 3x10mm 4x10mm 4x16mm 4x10mm ASSEMBLY OF THE CENTER DIFF. ONTO CHASSIS NO.6 94026 4x12mm...
  • Page 19 ASSEMBLY OF THE FRONT SERVO NO.7 Step 1 Step 2 34026 40541 94040 ..x4 Adjust 34026 Servo Washer in 3x8mm Washer accordance with use of servo. 34026 40541 94001 Sensor(Option) 3x5mm ..x3 Hex Screw 3x8mm 3x18mm 34026 94003 3x5mm 3x10mm ..x2 3x10mm Hex Screw...
  • Page 20 ASSEMBLY OF THE RADIO TRAY ONTO CHASSIS NO.7 3x12mm 94041 ..x1 Nylon Nut 94019 3x10mm ..x7 Flat Head Hex Screw 3x10mm 94004 3x12mm ..x1 Hex Screw 3x10mm 3x10mm 3x10mm ASSEMBLY OF THE FUEL TANK NO.5 NO.9 41035 Step 1 Step 2 Step 3 *Cut on 41035...
  • Page 21 ASSEMBLY OF THE FUEL TANK ONTO CHASSIS NO.9 37410 ASSEMBLY OF THE CLUTCH NO.8 Step 1 Step 2 *Place the clutch shoes with the clutch springs over the 3 pins of the flywheel. *Using a FLAT screw driver or needle nose pliers and bend the small end of *Fit the flywheel using a pair of the the clutch spring behind the pilot shaft...

  • Page 22: 4X4Mm

    ASSEMBLY OF THE ENGINE ONTO CHASSIS Note book Paper. NO.8 *Use note book paper to set gear backlash between spur gear and clutch bell gear, applying pressure while retightening the engine. 10114 *If the space is not correct the spur gear will be damaged.
  • Page 23 ASSEMBLY OF THE THROTTLE LINKAGES INTO BRAKE LEVER NO.7 Step 1 Step 2 Snap On 3x3mm 3x3mm 3x3mm 30802 #158 #158 A-53A Fuel Tube 3x3mm 30802 30172 3x10mm #158 3x3mm Set Screw * Use the screw ..x4 provided with your servo . 3x10mm Hex Screw ..x1...

  • Page 24: Step

    ASSEMBLY OF THE FRONT SHOCKS NO.10 *Assemble 2 sets for front Fit the o-ring into groove before Do Not Over Tighten assembly. 40060 Step 1 Step 2 Step 3 2.6x5mm 41008 41011 41006 41007 41012 41012 1mm Washer 41012 ..x2 2.6x5mm 41012 41006...

  • Page 25: X10Mm

    ASSEMBLY OF THE FRONT SHOCK ABSORBER 94041 ..x2 Nylon Nut Anti-Clockwise 40559 Rotate 94040 ..x2 Direction 3x8mm Washer 40643 Use left thread 94007 screw on the front 3x20mm ..x1 3x8mm right arm. Hex Screw 40559 Left Thread Hex Screw(Siliver) 3x20mm ..x1 Assembly for both right and left side.

  • Page 26: Hex Screw

    ASSEMBLY OF THE FUEL TUBE AND PRESSURE TUBE Connect to carbulater. Connect to fuel tank nipple. 10177 Connect to fuel nipple. Connect to fuel filter. Connect to pressure nipple. ASSEMBLY OF THE WING 3x12mm 40542 3x12mm Body Reamer (Not included) 40542 16015 Drill two 7mm holes for mounting.
  • Page 27 ASSEMBLY OF THE TIRE ONTO FRONT KNUCKLE AND REAR HUB Assembly for both right and left side. Tire and Wheel assembly. 40550 40550 40550 Wheel Nut ..x4 ASSEMBLY OF THE BODY AND PAINTING Cut out the body as shown. Use a neutral detergent to remove any dirt and oil. 40687 Before cutting and making holes on the body, put the unpainted body on the chassis...
  • Page 28 MOUNTING BODY 31159 Body Clip 31159 Body Clip STARTING OF THE ENGINE How to start the engine: 12V Starter and Starter Glow Plug 1.2V Glow Plug Igniter (Not Included) (Not Included) Ring ( Not Included) 1. Turn on transmitter and then receiver. 2.
  • Page 29 X2-CRT Set-Up Sheet Track Size Traction Surface open High Smooth Driver:_________________ Medium Medium Medium Track:_______________/____________________ Air Temp:_____80F_____ Tight Bumpy Front Suspension Steering Ackerman Location Shock Spring: _______Blue___________ Shock Piston: Standard Drilled Shock Oil wt: ________50__________ Shock Length Front Sway Bar Preload ( Center to Center) _______105.5mm______ Toe-IN: _________...
  • Page 31 X2-CRT Set-Up Sheet Track Size Traction Surface open High Smooth Driver:_________________ Medium Medium Medium Track:_______________/____________________ Air Temp:_____80F_____ Tight Bumpy Front Suspension Steering Ackerman Location Shock Spring: _______Blue___________ Shock Piston: Standard Drilled Shock Oil wt: ________50__________ Shock Length Front Sway Bar Preload ( Center to Center) _______105.5mm______ Toe-IN: _________...

  • Page 33: X28Mm

    34964 JAM M IN X2 PRO TRUGGY PARTS LIST OFNA DESCRIPTION RETAIL OFNA DESCRIPTION RETAIL 10013 SHO ES,ALUM SILVER-1.7gW /SPRING 29.95 40560 SERVO SAVER CON. PLATE H.C. 12.5 10098 CLUTCH NUT, SG SHAFT 4.95 40568 FRONT PLATE G RAPHITE 31.95 10101 SPRINGS,CLUTCH,GO LD 1.1M 3PCS 4.95...
  • Page 35 The registration card should be filled out and mailed to OFNA Racing within 10 days of purchase date. In the event that the kit is incomplete or component parts are broken due to error in manufacturer, contact your dealer from which you purchased the kit for replacement part or call OFNA at (949) 586-2910 for your nearest dealer location.