Summary of Contents for Ofna Racing Ultra LX 2e RTR
Page 3
OVERVIEW Components Transmitter Servo Brushless Motor,1900KV Brushless Electric Speed Controller (30693) ( 30694) Receiver Radio System Radio Control Car 40991 Parts Bag TOOLS NOT INCLUDED IN THE KIT Screw Cement Screw Cement Body Reamer Instant Cemment GEAR GREASE Cutter Curved Scissors Gear Grease Precision Caliper Needle Nosed Pliers...
Page 4
ATTENTION •Before plugging in your batteries and turning on your radio please read this page! 1. Check your brake and throttle dial on transmitter, and make sure it at MAX. Brake Forward 2. Turn on your transmitter. 3. Plug in your two 7.4v Lipo batteries. 4.
Page 6
HNT-3 2.4GHz RADIO SYSTEM OVERVIEW HNT-3 Transmitter 1.Transmitter Antenna *Carefully read the instruction manual of your 2.Servo Reverse Switches radio controller before using and keep it in a safe place as a reference introduction in the future. 3.TX RF Module And Binding Button 4.Power LED 5.Power Switch 6.Steering Dual Rate Trim LED...
CAUTION • To use your Radio with your models correctly and safely, read this manual carefully and keep it in a safe place for future reference. Warning: 1. This product is only equipped for radio controlled cars; 2. The usage of this product should be approved by local law or regulations; 3.
Page 8
AUX Channel Function (CH3) •This switch control the transmitter’s third channel. A servo plugged in this Channel 3 will move to full travel in one direction when the switch is in the “AUX” position, then move the switch to the “OFF” position the servo will move in the opposite position .
Page 9
CHECKING YOUR DUAL RATE •To Check Your Dual Rate: 1. Turn your radio “ON” then turn “ON” your vehicle. 2. Check your steering on your radio by turning left and right several times. 3. Now turn your steering wheel all the way to the left or right whichever you choose and hold it while pushing the “DEC”...
Steering Trim Please turn on your transmitter, plug in your battery and turn on your esc while making the adjustment of these settings. 1.Connect the receivers, servos, and other components and then turn on the power switches of the transmitter and receiver. 2.Be sure the steering trim and throttle trim on the transmitter are at their neutral position.
Page 11
Handling Procedure For Batteries Handling Procedure For Batteries NOTICE THE DIRECTION OF BATTERY COVER •Battery Replacement 1) Remove the battery cover from the transmitter by sliding it in the direction of the arrow. 2) Remove the used batteries. 3) Load the new 8 AA size alkaline, or Nickel Metal Hydride (NimH) rechargeable batteries, and pay very close attention to the polarity marking on the batteries.
Page 13
PLASTIC PARTS FOR USE 40536 30751 30751 30761 FRONT C HUB DIFF. CASE DIFF. CASE DIFF. CASE FRONT & REAR CENTER 34063 30010 REAR LOWER ARM FRONT AND REAR GEAR BOX 30657 FRONT LOWER ARM 36020 30351 30240 40643 FRONT UPPER ARM REAR LOWER ARM HOLDER BUMPER SHOCK PLASTIC PARTS...
Page 14
PLASTIC PARTS FOR USE 30674 30686 30270 SERVO SAVER FRONT STIFFENER WING STAY 16015 WING 41033 30662BATTERY CASE STONE GUARD SYMBOLS USED THROUGHOUT THE INSTRUCTION MANUAL Degrease With Do Not Ensure Free Contact Adhesive Tighten Ensure Parts Bag Used Motor Spray Over Tighten Movement Free...
ASSEMBLY OF THE FRONT AND REAR DIFF. Build two differentials for front and rear. 30901 Step 1 Step 2 30901 30620 30620 30751 94034 30751 4x4mm ..x2 Set Screw 30777 30777 30780 30769 30121 30769 3x5mm Screw ..x8 30779 4x4mm 30780 94004 3x12mm...
ASSEMBLY OF THE CENTER DIFF. MOTOR MOUNT 3x10mm 3x12mm 30653 Note: The width of the holes for front diff. Mount. 30675 94003 3x10mm ..x2 Hex Screw 94004 3x12mm ..x2 30201 Hex Screw ASSEMBLY OF THE FRONT GEAR CASE Step 1 Step 2 5x4mm 4x12mm...
ASSEMBLY OF THE KNUCKLE ARMS Assemble both right and left side. Step 1 Step 2 40520 94034 4x4mm ..x2 36053 Set Screw 36053 94042 ..x4 Step 3 Nylon Nut 40536 34053 40528 40527 40527 Knuckle Arm Bushing ..x4 36055 40528 King Pin Screw ..x4 40527...
ASSEMBLY OF THE FRONT STABILIZER Assemble both right and left side. Step 1 Step 2 94033 3x3mm ..x2 Set Screw 94035 3x8mm ..x2 Set Screw 94002 3x8mm ..x2 Hex Screw 3x3mm 3x8x0.8mm 94006 30341 3x18mm ..x2 Hex Screw 40199 3x18mm 3x8mm 34027 3x8x0.8mm...
ASSEMBLY OF THE FRONT GEAR CASE ONTO CHASSIS 94019 ..x2 3x10mm Flat Head Hex Screw 30240 94023 ..x2 3x25mm 30676 Flat Head Hex Screw 94026 ..x2 4x12mm Flat Head Hex Screw 4x12mm 4x16mm 94027 3x10mm ..x4 4x16mm 4x16mm Flat Head Hex Screw 3x25mm ASSEMBLY OF THE CENTER DIFF.
Page 23
ASSEMBLY OF THE REAR GEAR CASE ONTO THE CHASSIS Insert drive shaft into cap joint before assembling 36100 (86.5mm) center diff. 94023 3x25mm ..x2 Flat Head Hex Screw 4x16mm 3x25mm 4x16mm 94027 4x16mm ..x4 Flat Head Hex Screw ASSEMBLY OF THE STONE GUARD Assemble both right and left side.
ASSEMBLY OF THE ELECTRIC SPEED CONTRTOL Double side tape Electronic Speed Control 30693 90AMP ESC ASSEMBLY OF THE BATTERY TRAY BRIDGE ONTO BATTERY CASE 3x8mm 3x10mm 30662 94002 30662 3x8mm ..x2 Hex Screw 94003 30662 ..x2 3x10mm Hex Screw ASSEMBLY OF THE ELECTRIC SPEED CONTROL WIRE INTO RADIO CASE Step 1 Step 2...
Page 26
ASSEMBLY OF THE STEERING SERVO ONTO RADIO CASE 3x10mm 3x8x0.8mm 3x10mm 3x8x0.8mm Steering Servo 94003 ..x4 3x10mm Hex Screw 30662 94040 ..x4 3x8x0.8mm Washer ASSEMBLY OF THE SERVO WIRE INTO RADIO CASE ASSEMBLY OF THE BATTERY CASE ONTO CHASSIS 94019 3x10mm ..x3 Flat Head Hex Screw...
Page 27
ASSEMBLY OF THE RADIO CASE ONTO CHASSIS 3x10mm 3x10mm 94019 3x10mm ..x4 Flat Head Hex Screw ASSEMBLY OF THE RECEIVER INTO RADIO CASE 30560 Antenna Wire 3x8mm 40642 Please carefully read the Receiver Instruction 37410 Manuals before installation. 30662 *Plug in your speed controller 30662 Do not cut or shorten antenna wire.
MOTOR INSTALL Electric Motor (30694) Step detail *Approx. 20mm 30665-(14T) 4x4mm 94034 ..x1 4x4mm Set Screw MOTOR INSTALL Do Not Over Tighten 94038 3x12mm ..x2 3x12mm Cap Screw 3x8x0.8mm 94040 30694 3x8x0.8mm ..x2 Tighten the 3x12mm screw BRUSHLESS MOTOR Washer temporary.
Page 29
ASSEMBLY OF THE SHOCKS Assemble both left and right sides. 40060 40060 2.6x6x0.5mm Step detail 2.6x6x0.5mm 41011 Hold the shock rod at top of exposed 41011 thread with side cutting needle nosed pliers. 2.6x6x0.5mm Be careful not to damage the shock shaft.
Page 30
ASSEMBLY OF THE SHOCKS Assemble both left and right sides. Step 1 Step 2 41007 41006 Step detail Fit the o-ring into groove before assembly. 41007 P10 O-RING ..x4 FRONT SHOCK REAR SHOCK ASSEMBLY OF THE SHOCKS Assemble both left and right sides. 30403 Step detail Step detail...
Page 31
SETTING THE SHOCK REBOUND TO 50% & 0% (MEDIUM REBOUND & LOW REBOUND) TIGHTENED HALF WAY 50% TIGHTENED 100% TIGHTENED HALF WAY 50% TIGHTENED 100% Step 1 Step 2 Step 3 Step 1 Step 2 Step 3 ASSEMBLY OF THE SHOCKS SPRING Step 2 Step 3 Step 1...
Page 32
ASSEMBLY OF THE TIRES AND WHEELS Step 2 Step 1 Make four tires that are the same. 80025 Step detail Agglutination place Step 3 Use CA or “ Instant glue " and draw a round the rim where it attaches the tire . When it is dry glue the other side of the rim.
Page 33
BATTERY INSTALL If use hard case battery , make a hole as picture shown. 15mm Follow the manual instruction provided by ESC manufacturer to install the wire. MAKING HOLES AND CUTTING ON THE BODY SHELL Body Reamet (not included) For electric speed control cooling hole. Step 1 Step 2 10806 BLACK...
Page 34
PAINTING BODY SHELL Mask the windows on the inside with masking tape. PAINTING BODY SHELL Paint the body with polycarbonate spray paints. When the paint is dry, remove the masking tape. When you have finished painting, peel off the external protective films. MOUNTING THE BODY SHELL 31159 31159...
Page 38
SETTING GUIDE FRONT CAMBER ANGLE SETTING REAR CAMBER ANGLE SETTING Positive Negative Positive Negative Turnbuckle Turnbuckle Place the model car on flat surface. Raise the chassis to its maximum clearance before the wheels leave the ground. Adjust the length of the front and rear upper arms so that the wheels are vertical to the ground.
Page 39
34301 ULTRA LX2e RTR PARTS LIST OFNA DESCRIPTIONS RETAIL OFNA DESCRIPTIONS RETAIL 16015 HI FORCE WING, 1/8 WHITE 15.95 34055 PINS, LOWER REAR ARMS 3x42.6mm 15.95 30010 GEARBOX, ULTRA SERIES 14.95 34063 FRONT & REAR LOWER ARMS 13.95 30082 CAP JOINTS, 6mm, 2 PCS. 9.95 36020 FRONT UPPER ARMS, 2 PCS.
Page 41
TO: OFNA TECHNICAL SUPPORT 7 VANDERBILT, IRVINE, CA 92618 TODAY’S DATE: month________day______ 1. Print out form. 2. Fill out the form completely. 3. Make a copy of purchase receipt. All replacements/repairs will not be processed, unless accompanied by proof that item(s) was purchased in the last 30 days. 4.
Page 43
OFNA Racing congratulates you on your purchase of our fine OFNA Product. With proper maintenance and han- dling this kit will provide many hours of enjoyment. The registration card should be filled out and mailed to OFNA Racing within 10 days of purchase date. IMPORT ANT!