Specifications; Standard Accessories - Hitachi M 6SB Handling Instructions Manual

5) Service
a) Have your power tool serviced by a qualifi ed repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of children
and infi rm persons.

SPECIFICATIONS

Voltage (by areas)*
Power input*
No-load speed
Collet Chuck Capacity
Weight (Only main body)
* Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

(1) Trimmer guide ass'y .....................................................1
(2) Straight Guide ..............................................................1
(3) Template Guide (with two M4 screws) .........................1
(4) Wrench 17/19 mm .........................................................1
Standard accessories are subject to change without
notice.
APPLICATIONS
○ Plywood trimming
○ Various beveling
○ Various grooving
○ Engraving
○ Cut off s
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If the
plug is connected to a receptacle while the power switch
is in the ON position, the power tool will start operating
immediately, which could cause a serious accident.
3. Extension cord
When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Fitting the bit
Refer to "Fitting and removal of the bit" section given
in the following. It is dangerous if the bit is not fi tted to
the coIlet chuck securely. Check if the collet chuck is
suffi ciently tightened.
5. Cutting using the workpiece edge as a base line
(Fig. 1)
Note that the distance between the machine center and
the hollow diff ers from the other three distances.
PRECAUTIONS ON USING TRIMMER
1. Always use the bit of correct shank diameter suitable for
the speed of the tool.
2. Hold the body fi rmly during operation. Otherwise,
injuries can result.
3. The bit is very hot immediately after operation. Avoid
bare hand contact with the bit for any reason.
4. Avoid bringing your hand, face, etc., close to the bit and
rotary parts during operation.
5. Exercise caution as the bit remains rotating even after
the switch is turned off . Contact of your hand, etc., with
the rotating bit can result in injuries.
(110 V, 230 V, 240 V)
440 W
30000 min
6 mm or 6.35 mm (1/4")
1.4 kg
6. Confi rm the spindle lock mechanism.
Confi rm that the spindle lock is disengaged by pushing
the push button two or three times before switching the
power tool on. (See Fig. 2)
FITTING AND REMOVAL OF THE BIT
1. Fitting the bit
(1) Remove the base ass'y from the body. When loosening
the wing nut (See Fig. 3), the base ass'y can be
removed.
(2) Deeply inset the bit into the collet chuck hole. (The
distance is 15 mm or more from side of collet chuck.)
(3) Depress spindle lock (Fig. 2) and rotate collet nut
clockwise by hand until lock engages hole in motor
spindle.
(4) While holding spindle lock engaged, tighten collet nut
securely by turning clockwise using wrench provided.
CAUTION
○ Make sure to tighten the collet chuck after inserting
the bit. Collet chuck may be damaged if it is tightened
without inserting the bit.
○ Avoid depressing the lock pin while the bit is still in
rotation. Because, there is a fear that doing so may
result in an abnormal noise or damage in the fi xed
section of the rotating shaft.
(5) Fit the removed base assembly to the rack provided on
the body's outer housing after adjusting the pinion of
the base assembly thereto. Then tighten the wing nut
and fi x the assembly securely.
2. Removal of the bit
Loosen the collet chuck in the reverse manner as
described for the fi tting the bit.
CAUTION
Bit is heated after the cutting work.
Do not touch it directly.
English
-1
7