Washer Maintenance - Maytag 3LMVWC400YW Use And Care Manual

WASHER MAINTENANCE

WATER INLET HOSES
Replace inlet hoses after 5 years of use to reduce the risk of
hose failure. Periodically inspect and replace inlet hoses if
bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, mark the date of replacement
on the label with a permanent marker.
WASHER CARE
Recommendations to Help Keep Your Washer Clean and
Performing at its Best
1. Always use High Efficiency (HE) detergents and follow the
HE detergent manufacturer's instructions regarding the
amount of HE detergent to use. Never use more than the
recommended amount because that may increase the rate
at which detergent and soil residue accumulate inside your
washer, which in turn may result in undesirable odor.
2. Use warm and hot wash water settings sometimes (not
exclusively cold water washes), because they do a better
job of controlling the rate at which soils and detergent
accumulate.
3. Always leave the washer lid open between uses to help dry
out the washer and prevent the buildup of odor-causing
residue.
Cleaning Your Top Loading Washer
Read these instructions completely before beginning the
routine cleaning processes recommended below. This Washer
Maintenance Procedure should be performed, at a minimum,
once per month or every 30 wash cycles, whichever occurs
sooner, to control the rate at which soils and detergent may
otherwise accumulate in your washer.
Cleaning the Inside of the Washer
To keep your washer odor-free, follow the usage instructions
provided above, and use this recommended monthly cleaning
procedure:
Clean Washer Cycle
This washer has a special cycle that uses higher water volumes
in combination with liquid chlorine bleach to clean the inside
of the washer.
Begin procedure
1. Chlorine Bleach Procedure:
a. Open the washer lid and remove any clothing
or items.
b. Add 236 mL (1 cup) of liquid chlorine bleach
to the bleach compartment.
NOTE: Use of more liquid chlorine bleach than is
recommended above could cause washer damage
over time.
c. Close the washer lid.
d. Do not add any detergent or other chemical
to the washer when following this procedure.
e. Select the CLEAN WASHER cycle.
f. Press the START/Pause/Unlock button to begin the
cycle. The Clean Washer Cycle Operation is described
below.
WASHER CARE (cont.)
NOTE: For best results, do not interrupt cycle. If cycle
must be interrupted, press POWER/CANCEL. (For models
with no POWER/CANCEL button, press and hold START/
Pause/Unlock for three seconds). After the Clean Washer
cycle has stopped, run a RINSE & SPIN cycle to rinse cleaner
from washer.
Description of Clean Washer Cycle Operation:
1. This cycle will fill to a water level higher than in normal
wash cycles to provide rinsing at a level above the water line
for normal wash cycle.
2. During this cycle, there will be some agitation and spinning
to increase the removal of soils.
After this cycle is complete, leave the lid open to allow
for better ventilation and drying of the washer interior.
Cleaning the Dispensers
After a period of using your washer, you may find some residue
buildup in the washer's dispensers. To remove residue from
the dispensers, wipe them with a damp cloth and towel dry.
Do not attempt to remove the dispensers or trim for cleaning.
The dispensers and trim are not removable. If your model has
a dispenser drawer, however, remove the drawer and clean
it before or after you run the Clean Washer cycle. Use an all-
purpose surface cleaner, if needed.
Cleaning the Outside of the Washer
Use a soft, damp cloth or sponge to wipe away any spills.
Use only mild soaps or cleaners when cleaning external washer
surfaces.
IMPORTANT: To avoid damaging the washer's finish, do not
use abrasive products.
NON-USE AND VACATION CARE
Operate your washer only when you are home.
If moving, or not using your washer for a period of time,
follow these steps:
1. Unplug or disconnect power to washer.
2. Turn off water supply to washer, to avoid flooding due
to water pressure surge.
WINTER STORAGE CARE
IMPORTANT:
To avoid damage, install and store washer
where it will not freeze. Because some water may stay in
hoses, freezing can damage washer. If storing or moving
during freezing weather, winterize your washer.
To winterize washer:
1. Shut off both water faucets; disconnect and drain water
inlet hoses.
2. Put 1 L (1 qt.) of R.V.-type antifreeze in basket and run
washer on RINSE & SPIN cycle for about 30 seconds to
mix antifreeze and remaining water.
3. Unplug washer or disconnect power.
11