Side-By-Side Installation - GE Monogram ZTD910SFSS Dimension Manual

GE Monogram
®
INSTALLATION BELOW A CABINET DRAWER
ZDT910SFSS
ZDT910SFSS
ZDT910SFSS
1/4"
1/4"
(.6)
min.
(.6)
min.
1/4"
(.6)
min.
9 1/4"
9 1/4"
(23.5)
Cut-out
(23.5)
9 1/4" height
Cut-out
height
(23.5)
Cut-out
1"
height
1"
(2.5)
min.
(2.5)
min.
1"
Above
toe-kick
Above
(2.5)
min.
toe-kick
Above
toe-kick
SIDE BY SIDE INSTALLATION
PROVIDING CABINET SUPPORT
2" x 4"
(5.1)
2" x 4"
or Equivalent Runners (5.1)
or Equivalent Runners
2" x 4"
(5.1)
or Equivalent Runners
23 1/2"
23 1/2"
(59.7)
(59.7)
23 1/2"
(59.7)
25"
(63.5)
25"
(63.5)
30"
(76.2)
30"
(76.2)
25"
(63.5)
30"
(76.2)
30" Warming Drawer
B
C
23 1/2"
(59.7)
23 1/2"
(59.7)
min. cutout width
min. cutout width
23 1/2"
(59.7)
SIDE VIEW
min. cutout width
SIDE VIEW
SIDE VIEW
D
2" min.
(5.1)
2" min.
Between cut-outs
(5.1)
Between cut-outs
2" min.
(5.1)
Between cut-outs
INSTALLING ANTI-TIP BLOCKS
(10.2)
(10.2)
(10.2)
E
TOP VIEW
TOP VIEW
Side cleats
TOP VIEW
Side cleats
A
Side cleats
A
28 1/2"
(72.4)
28 1/2"
(72.4)
min. cutout width
min. cutout width
28 1/2"
(72.4)
min. cutout width
FRONT VIEW
FRONT VIEW
FRONT VIEW
2"
2"
2"
2"
Anti-tip Block against 2"
rear cabinet wall 9" from
Anti-tip Block against
2"
rear cabinet wall 9" from floor to bottom of block
floor to bottom of block
Anti-tip Block against
rear cabinet wall 9" from
floor to bottom of block
2" x 4"
(5.1) (10.2)
2" x 4"
or
(5.1) (10.2)
2" x 2"
(5.1) (5.1)
or
2" x 2"
Runners or Solid Bottom 2" (5.1) x 4" (5.1)
(5.1) (10.2)
Runners or Solid Bottom
or
2" x 2"
(5.1) (5.1)
Runners or Solid Bottom
ZTD910SFSS
NOTES
A If you are installing in
frameless cabinets,
it may be necessary
to install 1/2" wide
cleats to accept drawer
mounting screws. See
drawer for mounting
screw locations.
B Install a 2"x2" or 2"x4"
anti-tip block against
rear wall, 9" from floor
of cutout to bottom
of block. The anti-tip
block must be installed
to prevent the drawer
from tipping forward
when opened and
loaded. Failure to add
the anti-tip block could
result in personal injury.
C When installing the
warming drawer below
a cabinet drawer, a
solid barrier must be
installed at least above
the warming drawer
to block access. Use
any solid material such
as 1/4" thick plywood.
Allow at least 1/4"
air gap between the
barrier and the top of
the warming drawer.
Observe the 5" min.
above the floor or 1"
min. above the toe kick
installation height.
D When installing two
warming drawers side
by side, install them
in separate cut-outs
and allow a 2" min. gap
between each cut-out.
E The warming drawer
may be supported by
either a solid bottom or
2"x2" or 2"x4" runners.
The support must
Install
x 4" be level and rigidly
(5.1) Install (10.2)
B
x 4"
or
mounted, flush with
(5.1) (10.2)
x 2"
(5.1) or (5.1)
Install the bottom edge of the
x 2"
x 4"
(5.1) (5.1)
(5.1) (10.2)
cut-out (there is no way
or
x 2"
to level the drawer once
(5.1) (5.1)
it has been installed,
so make sure that the
supports are level). The
floor or runners must be
capable of supporting
at least 150 lbs.
For more details refer
to the installation
instructions for this
product.
Product Specification Created 8/14