Osd Transparency; Hot Key - NEC MultiSync LCD3090WQXi User Manual

OSD LOCK OUT
This control completely locks out access to all OSD control functions. When attempting to activate OSD controls
while in the Lock Out mode, a screen will appear indicating the OSD controls are locked out.
There are four types of OSD LOCK OUT:
OSD LOCK OUT with BRIGHTNESS and CONTRAST control: To activate the OSD Lock Out function, press
SELECT, then the "UP" button and hold down simultaneously. To deactivate the OSD Lock Out, press SELECT, then
the "UP" button and hold down simultaneously while in the OSD menu. BRIGHTNESS and CONTRAST can be
adjusted while in this lock out mode.
OSD LOCK OUT with no control: To activate the OSD Lock Out function, press SELECT, then the "Right" button and
hold down simultaneously. To deactivate the OSD Lock Out, press SELECT, then the "Right" button and hold down
simultaneously while in the OSD menu. No controls can be adjusted while in this lock out mode.
OSD LOCK OUT with BRIGHTNESS (only) control: To activate the OSD Lock Out function, press SELECT, then the
"Down" and "Left" buttons and hold down simultaneously. To deactivate the OSD Lock Out, press SELECT, then the
"Down" and "Left" buttons and hold down simultaneously while in the OSD menu. Only the BRIGHTNESS can be
adjusted while in this lock out mode.
CUSTOM: Refer to the Advanced OSD Menu.

OSD TRANSPARENCY

Adjusts the transparency of the OSD Menu.
OSD COLOR
"Tag window frame color", "Item select color" and "Adjust window frame color" can be changed to Red, Green, Blue,
or Gray.
RESOLUTION NOTIFIER
This optimal resolution is 2560 x 1600. If ON is selected, a message will appear on the screen after 30 seconds,
notifying you that the resolution is not at 2560 x 1600.

HOT KEY

You can adjust the BRIGHTNESS and CONTRAST directly. When this function is set to ON, you can adjust the
brightness with the "Left" or "Right" buttons, and the contrast with the "Down" or "Up" buttons, while the OSD menu is
off. The standard OSD can be accessed with the EXIT button.
FACTORY PRESET
Selecting Factory Preset allows you to reset all OSD control settings (BRIGHTNESS, CONTRAST, ECOMODE, AUTO
BRIGHTNESS, BLACK LEVEL, IMAGE CONTROL, COLOR CONTROL SYSTEM, SHARPNESS, OFF TIMER, OFF
MODE, OSD LEFT/RIGHT, OSD UP/DOWN, OSD TURN OFF, OSD TRANSPARENCY) back to the factory settings.
Individual settings can be reset by highlighting the control to be reset and pressing the RESET button.
Information
Provides information about the current resolution display and technical data including the preset timing being used
and the horizontal and vertical frequencies. Indicates the model and serial numbers of your monitor.
NOTE: When connected to digital input, the OSD will show either DIGITAL(D) if a dual link signal is detected or
DIGITAL(S) if a single link signal is detected.
OSD Warning
OSD Warning menus disappear with Exit button.
NO SIGNAL: This function gives a warning when there is no Horizontal or Vertical Sync. After power is
turned on or when there is a change of input signal, the No Signal window will appear.
RESOLUTION NOTIFIER: This function warns if resolution other than the optimized resolution is used. After
power is turned on or when there is a change of input signal or the video signal doesn't have proper
resolution, the Resolution Notifier window will open. This function can be disabled in the MENU Tools OSD.
OUT OF RANGE: This function gives a recommendation of the optimized resolution and refresh rate. After
the power is turned on or there is a change of input signal or if the video signal doesn't have proper timing,
the Out Of Range menu will appear.
PORTRAIT WARNING: When the monitor is used in the portrait position, the brightness value will be
reduced to 300 cd/m
appear on the screen for 10 seconds.
LUMINANCE WARNING: When the backlight cannot display the desired luminance, a message will
appear on the display. To avoid this, reduce the BRIGHTNESS level or set the AUTO LUMINANCE
function to OFF (page 15, TAG1).
NOTE: It is possible to change the DVI SELECTION, to change the OFF MODE or to change the HDCP
For advanced user menu see "Appendix".
01_English
2
. If the Portrait Warning is ON, a message warning of the change in brightness will
CONTENT settings while the "NO SIGNAL" or "OUT OF RANGE" messages are displayed.
14
English-14
1/25/08, 8:53 AM