NEC LCD3090WQXI-BK-R User Manual

NEC LCD3090WQXI-BK-R User Manual

30" widescreen color-critical desktop monitor

Advertisement

MultiSync LCD3090WQXi
User's Manual

Advertisement

Table of Contents
loading

Summary of Contents for NEC LCD3090WQXI-BK-R

  • Page 1 MultiSync LCD3090WQXi User’s Manual...
  • Page 2: Table Of Contents

    Index Warning, Caution ... English-1 Declaration ... English-1 Canadian Department of Communications Compliance Statement ... English-2 Declaration of Conformity ... English-2 Recommended use ... English-3 Contents ... English-5 Quick Start ... English-6 Controls ... English-10 Specifications ... English-15 Features ... English-16 Troubleshooting ...
  • Page 3: Warning, Caution

    U.S. registered trademark. NERGY ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy, Norway, Spain, Sweden, U.K. All other brands and product names are trademarks or registered trademarks of their respective owners.
  • Page 4: Canadian Department Of Communications Compliance Statement

    Tel. No.: Type of Product: Equipment Classification: Models: Non shield type, 3-conductor 2.0 m U.S.A NEC Display Solutions of America, Inc. 500 Park Blvd, Suite 1100 Itasca, Illinois 60143 (630) 467-3000 Display Monitor Class B Peripheral MultiSync LCD3090WQXi (L307TD) We hereby declare that the equipment specified above conforms to the technical standards as specified in the FCC Rules.
  • Page 5: Recommended Use

    NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.
  • Page 6 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen.
  • Page 7: Contents

    Contents Your new NEC monitor box* should contain the following: • MultiSync LCD3090WQXi monitor with tilt/swivel/pivot/height adjust stand • Power Cord • Video Signal Cable (15-pin mini D-SUB male to DVI-A) • Video Signal Cable (DVI-D to DVI-D cable) •...
  • Page 8: Quick Start

    6. Make sure all cables are resting flat against the stand (Figure C.3). Please check Tilt, Rise and Lower monitor screen and screen rotation when you manage cables. DC-OUT NEC optional product attachment. Do not use this connector unless specified.
  • Page 9 Figure C.3 7. Hold all cables firmly and place the cable cover onto the stand (Figure D.1). To remove the cable cover, lift the cover off as shown in Figure D.2. 8. Connect one end of the power cord to the AC inlet on the back of the monitor and the other end to the power outlet. NOTE: Please refer to Caution section of this manual for proper selection of AC power cord.
  • Page 10: Raise And Lower Monitor Screen

    Raise and Lower Monitor Screen The monitor may be raised or lowered in either Portrait or Landscape mode. To raise or lower screen, place hands on each side of the monitor and lift or lower to the desired height (Figure RL.1). NOTE: Handle with care when raising or lowering the monitor screen.
  • Page 11: Flexible Arm Installation

    Flexible Arm Installation This LCD monitor is designed for use with a flexible arm. To prepare the monitor for alternate mounting purposes: NOTE: The monitor must be installed or moved by two or more people. • Refer to instructions included with the flexible arm for detailed instructions. •...
  • Page 12: Controls

    Controls OSD (On-Screen Display) control buttons on the front of the monitor function as follows: To access OSD menu, press the MENU button. To change signal input, press the SELECT button. NOTE: OSD must be closed in order to change signal input. 1 AUTO DIMMING SENSOR Detects the level of ambient light, allowing the monitor to make adjustments to various settings, resulting in a more comfortable viewing experience.
  • Page 13: Eco Mode

    Brightness/Contrast Controls BRIGHTNESS Adjusts the overall image and background screen brightness. NOTE: The upper portion (higher settings) of the brightness level is adjusted using the backlight output. If a very low brightness level (low setting) is used the contrast level may be reduced. The display will digitally compensate for low brightness level.
  • Page 14: Color Control Systems

    FINE (Analog input only) Improve focus, clarity and image stability by increasing or decreasing this setting. If the “Auto Adjust function” and the “H.Size” function do not give you a satisfactory picture setting, a fine tuning can be performed using the “Fine” function. For this a Moiré...
  • Page 15: Off Timer

    HDCP CONTENT (Digital Input Only) Selects the type of input to be used with HDCP CONTENT. OFF: When a PC or other computer equipment is connected, select “OFF”. ON: When a DVD player or other type of high definition device is connected, select “ON”. NOTE: Interlaced signals (480i, 576i, 1080i) are not supported.
  • Page 16: Osd Transparency

    OSD LOCK OUT This control completely locks out access to all OSD control functions. When attempting to activate OSD controls while in the Lock Out mode, a screen will appear indicating the OSD controls are locked out. There are four types of OSD LOCK OUT: OSD LOCK OUT with BRIGHTNESS and CONTRAST control: To activate the OSD Lock Out function, press SELECT, then the “UP”...
  • Page 17: Specifications

    60 Hz 1920 x 1440* at 60 Hz (Digital) 2560 x 1600 at 30 Hz 2560 x 1600 at 60 Hz (Digital)...NEC DISPLAY SOLUTIONS cites 480P (720 x 480* at 60 Hz) 576P (720 x 576* at 50 Hz)
  • Page 18: Features

    Allows for the monitor to be mounted on a wall or an arm using any third party compliant device. Visual Controller: Is a ground-breaking software family, developed by NEC Display Solutions Europe GmbH, providing intuitive access to all monitor setting controls and remote diagnosis via the Windows interface, based upon the VESA standard, DDC/CI. Using a standard VGA or DVI signal cable, Visual Controller can either benefit single users or, with Visual Controller Administrator, can reduce the Total Cost of Ownership through remote network-wide maintenance, diagnosis and asset-reporting.
  • Page 19: Troubleshooting

    NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.
  • Page 20: Appendix

    Appendix If you need detailed information about the controls, please use the advanced menu. <How to use the advanced menu> • Turn off your monitor. • Turn on your monitor by pushing the “POWER” and “SELECT” button at the same time for at least one second simultaneously.
  • Page 21 Tag2 R-H.position Adjusts the position of the red component of the image. Press “Left” or “Right” to adjust. (Analog input only) G-H.position Adjusts the position of the green component of the image. Press “Left” or “Right” to adjust. (Analog input only) B-H.position Adjusts the position of the blue component of the image.
  • Page 22 2: DICOM gamma is recommended for grayscale medical images. Factory calibrated to DICOM Grayscale Display Function for optimum human visual perception. PROGRAMMABLE: A programmable gamma curve can be loaded using NEC software. Custom Value: The gamma value ranges between 0.5 to 4.0 in 0.1 increments.
  • Page 23 Tag6 Color Control Color Control Systems: Seven preset color settings. For preset settings 1, 2, 3 and 5, the following levels can be adjusted: TEMPERATURE: Adjust the white temperature by increasing or decreasing this setting. A lower color temperature will make the screen reddish and a higher color temperature will make the screen bluish.
  • Page 24 BOOT LOGO The NEC logo is briefly displayed after the monitor is powered on. This feature can be turned on or off in the OSD. Note: If the “EXIT” button is kept pressed while NEC logo is displayed, the BOOT LOGO menu will appear.
  • Page 25 Hot Key When this function is activated; the brightness and contrast of the monitor can be adjusted without entering the OSD menu by using the front buttons. The “Left” or “Right” buttons adjust the brightness level. The “Down” or “Up” buttons adjust the contrast level. Factory Preset Selecting Factory Preset allows you to reset all OSD control settings back to the factory settings.
  • Page 26 TagA Tile Matrix TagB Date & Time TagC Schedule TagD Eco Mode Information TagE Information The Tile Matrix feature allows one image to be displayed over multiple screens. This feature can be used with up to 25 monitors (5 vertical and 5 horizontal). Using Tile Matrix requires the PC output signal be sent through a distribution amplifier to each individual monitor.
  • Page 27: Self Calibration

    Self Calibration Simply connect the external USB sensor, and the brightness, white tint and gamma levels are calibrated without the need of a computer. This feature works for displays requiring RGB calibration and graphical calibration. Before proper self calibration can be performed, display should warm-up for a minimum 30 minutes. If the USB sensor is plugged in before the monitor is warmed up, a warning will appear on-screen (Figure S.3).
  • Page 28 7. The procedure will ask for the USB sensor to be placed on the center of the display panel (Figure S.7). Tilt the display panel approximately 5˚ backward and place the USB sensor in the center of the display panel (Figure S.1). NOTE: Place the USB sensor flat against the LCD to avoid external light contamination.
  • Page 29: White Point Matching/Copy Calibration

    White Point Matching/Copy Calibration Calibration settings can be copied from one display to one or more additional displays. Using this feature reduces the variation between different displays allowing them to match each other more closely. Before proper copy calibration can be performed, displays should warm-up for a minimum 30 minutes. If the sensor is plugged in before the minute warm-up, a warning will appear on-screen (Figure C.4).
  • Page 30 6. Using “LEFT” or “RIGHT” of Display B, select COPY in the MODE selection (Figure C.7). Select ON of OFF in the SELF selection. If ON selected, SELF Calibration execute with COPY Calibration. 7. Select the target GAMMA: NO CORRECTION, 2.2, OPTION, PROGRAMMABLE and CUSTOM. Please select the same target GAMMA as Display A.
  • Page 31: Using The Auto Brightness Function

    Using the Auto Brightness function The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordingly.
  • Page 32: Tco'03

    TCO’03 Some of the features of the TCO’03 Display requirements: Ergonomics • Good visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance, color rendition and image stability. Energy •...
  • Page 33: Tco'06

    TCO’06 (TCO’06 compliant with Response Improve feature set ON (see page 22 in this manual). Products certified to TCO´06 Media Displays are specifically designed for high quality reproduction of moving images. Features such as luminance, colour rendition and response time are important when watching TV or working with media, graphics, web design and other applications that demand outstanding moving images.* Other features of TCO’06 Media Displays: Ergonomics...
  • Page 34: Manufacturer's Recycling And Energy Information

    Manufacturer’s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally- friendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).

Table of Contents