Helion Intrusion XLR HLNA0684 Owner's Manual
Hide thumbs Also See for Intrusion XLR HLNA0684:

Advertisement

ENGLISH-US
Owner's Manual for: HLNA0684, HLNA0685
LENGTH
431.50mm (17in)
WIDTH
335.50mm (13.2in)
HEIGHT
226.30mm (8.9in)
WHEELBASE
286.40mm (11.3in)
WHEEL SIZE
55.88mm (2.2in) x 72mm (2.83in) x 45.20mm (1.78in)
WHEEL OFFSET
12mm Hex, Invictus and TRA Compatible
WEIGHT*
1975g (4.35lb)
BATTERY
3,000mAh NiMH 7-CELL, 8.4V, HCT-Plug
MOTOR
3000 kV Radient Reaktor4 4-Pole Brushless, Sensorless
RADIO
High-Power HRS3.2 2.4Ghz 3-Channel w/ D/R, EPA,
REV, FS
CHARGER
AC 1A, NiMH only
*APPROXIMATE OUT-OF-THE-BOX WEIGHT
• Entire contents ©2015 Helion RC
• Before using your product, review all documentation and inspect the products carefully. If for some reason you decide it
is not what you wanted, then do not continue with unpacking, setup or operation of your product. Your local hobby dealer
cannot accept a product for return or exchange after partaking in actions that produce wear and tear.
• Read, understand and follow all instructions and accompanying material carefully before operating or assembling your
vehicle to prevent serious damage to your vehicle. Failure to complete these tasks properly or intentional aversion to the
content will be considered abuse and/or neglect.
• Product specifications are subject to change without notice. Due to ongoing development, the actual product may vary
from images shown.
• This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive
harm.
• This product is not a toy! (14+) Recommended for ages 14 and up. Adult supervision required for ages under 18 years
old. Contains small parts, keep out of reach of children 3 years of age and younger.
Now compatible with IKONNIK Xenon protocol systems

Advertisement

Table of Contents
loading

Summary of Contents for Helion Intrusion XLR HLNA0684

  • Page 1 AC 1A, NiMH only *APPROXIMATE OUT-OF-THE-BOX WEIGHT • Entire contents ©2015 Helion RC • Before using your product, review all documentation and inspect the products carefully. If for some reason you decide it is not what you wanted, then do not continue with unpacking, setup or operation of your product. Your local hobby dealer cannot accept a product for return or exchange after partaking in actions that produce wear and tear.
  • Page 2: Package Contents

    For other issues it should be known that hobby grade radio controlled products such as those offered by Helion RC differ from toy grade, in that they are intended to be user- servicable products where the user can disassemble and maintain their own product using factory replacement parts.
  • Page 3: Getting Started

    1/10th SCALE 2WD MONSTER TRUCK GETTING STARTED 1. Remove the body and battery from vehicle to prepare for charging. a. Open battery compartment in your vehicle by rotating the thumb knobs to align with the openings and then lift up the strap.
  • Page 4 PRECAUTIONS WHEN USING RADIO CONTROLLED PRODUCTS • Your model can cause serious damage or injury so please use caution and courtesy when operating your model. • Do not expose the radio system to water or excessive moisture. • As a safety precaution, perform all transmitter and receiver adjustments with the vehicle’s wheels off the ground. This ensures the complete control over the vehicle at all times during adjustments.
  • Page 5 1/10th SCALE 2WD MONSTER TRUCK IKONNIK XENON HRS3.2 PROTOCOL, PAIRING AND FAIL SAFE SETTING ing the AA batteries or rechargeable battery pack. 12. Fail Safe setting and Channel 3 toggle. 13. Beginner Mode/Feature Lock Out 14. Reset Button Understanding Protocol and Pairing the Transmitter and Receiver: The process of allowing communication to occur between a 2.4GHz transmitter and receiver is called “pairing”...
  • Page 6: End Point Adjustment

    IKONNIK XENON HRS3.2 CONNECTION AND CONFIGURATION NOTE: AS A SAFETY PRECAUTION, PERFORM THE FAIL-SAFE ADJUSTMENTS WITH THE VEHICLE’S WHEELS OFF THE GROUND. 1. Turn the transmitter and receiver ON and move the throttle trigger to the desired position. 2. Press the Fail-Safe button for 5 seconds to program the throttle Fail-Safe setting. It is recommended and common to set the throttle Fail-Safe as Full Brake, i.e.
  • Page 7 1/10th SCALE 2WD MONSTER TRUCK ...IKONNIK XENON HRS3.2 CONFIGURATION CONTINUED to the desired location. • Throttle and Brake End Point Adjustment (EPA) › Use this function to adjust throttle and brake travel adjustments. › Throttle Adjustment: » Pull the throttle trigger completely to full throttle and use the “TH+” or “TH-“ buttons to adjust the throttle end point to the desired location.
  • Page 8 IKONNIK XENON HRS3.2 STANDARD OPERATION may not provide consistent performance and is not recom- mended for beginners. For detailed setup information refer to the ESC setup section of this manual. Turn Left Standard operation: • When looking at the face of the transmitter wheel: Turn Right ›...
  • Page 9 1/10th SCALE 2WD MONSTER TRUCK RADIENT REAKTOR 50-4 BRUSHLESS SYSTEM OVERVIEW The Radient Reaktor series brushless motor and ESC is a great power ESC TECHNICAL SPECIFICATIONS plant to satisfy your need for speed and performance as an entry level Continuous Cur- brushless system.
  • Page 10 ...RADIENT REAKTOR BRUSHLESS SYSTEM OVERVIEW CONTINUED • Protection Functions: › Low voltage cut-off protection: If the voltage of a Lipo battery pack is lower than the threshold for 2 seconds, the ESC will cut of the output power. Please note that the ESC cannot be restarted if the voltage of each Lipo cell is lower than 3.5V.
  • Page 11 1/10th SCALE 2WD MONSTER TRUCK CALIBRATING AND PROGRAMMING YOUR ESC CONTINUED... Programming your ESC: The Radient Reaktor is a programmable ESC. Although the default settings should work well for most users, these settings exist so that you can fine tune the performance of your ESC to your experience and components. It’s various program- mable parameters can be adjusted either by interfacing with the ESC directly button presses and counting LED flashes, or via the optional Reaktor Program Box (RDNA0031) which includes a digital readout of the settings for easier interpreta- tion and faster setup.
  • Page 12 ...PROTECTION MODES AND ERROR CODES CONTINUED Item 4: Start Mode/Punch (Higher value is more aggressive): The Reaktor ESC has 4 “punch” profiles that allow you to tune the initial power output of the ESC to suit your driving, ve- hicle, and the surface. You will typically want a lower punch setting when the surface has less traction. To get the optimal performance out of LiPo batteries, on high traction sufaces, setting 4 is recommended.
  • Page 13: Programming Process

    1/10th SCALE 2WD MONSTER TRUCK PROGRAMMING PROCESS Programmable Value (Blinks of RED LED), Black background = default settings Programmable Items Turn OFF ESC and (Blinks of GREEN LED) Transmitter Forward/ Forward Running Mode Reverse with Brake with Brake Press and hold the SET button then Drag Brake Force Turn ON the ESC...
  • Page 14 PROGRAMMING PROCESS TROUBLESHOOTING Problem / Symptom Possible Cause Possible Solution Receiver and transmitter not bound Try re-pairing ESC will not set to trans- Throttle Channel not set to Reverse Unless using Futaba radio, set Th channel to Reverse mitter Batteries dead in car or transmitter Replace batteries Transmitter is too close to vehicle Hold transmitter farther away from vehicle...
  • Page 15: Safety Tips

    Always use caution and common sense as failure to operate your Helion RC product in a safe and responsible manner can result in damage to the product or other properties.
  • Page 16 If you plan to run for extended periods of time in light or heavy rain It is recommended to secure the receiver in an additional all weather membrane. Since the Helion HRS3.2 receiver is a micro size receiver, fitting it into a balloon is fairly easy.
  • Page 17: Storage And Disposal

    1/10th SCALE 2WD MONSTER TRUCK GENERAL CARE AND MAINTENANCE CONTINUED... producing a “wheelie”. While this looks impressive, we caution you to readjust the slipper to prevent the “wheel- ie” since you cannot turn the vehicle to avoid collisions when the front wheels are in the air. 5.
  • Page 18: Troubleshooting Problems

    TROUBLESHOOTING PROBLEMS Before contacting customer support, recall that this is a hobby grade product intended to be user serviceable. Please take the time to fully inspect your product for any obvious causes to the issues you are experi- encing. Below are some of the most common issues experienced. 1.
  • Page 19: Troubleshooting Guide

    1/10th SCALE 2WD MONSTER TRUCK TROUBLESHOOTING GUIDE Problem / Symptom Possible Cause Possible Solution Battery voltage too low Charge battery Vehicle will not turn on Battery not connected Re/connect battery Damaged battery Replace battery Battery voltage too low Charge or change batteries Transmitter will not turn Battery/ies installed improperly Correct installation...
  • Page 20 FRONT SUSPENSION ASSEMBLY...
  • Page 21: Chassis Assembly

    1/10th SCALE 2WD MONSTER TRUCK CHASSIS ASSEMBLY...
  • Page 22: Rear Suspension Assembly

    REAR SUSPENSION ASSEMBLY...
  • Page 23: Transmission Assembly

    1/10th SCALE 2WD MONSTER TRUCK TRANSMISSION ASSEMBLY...
  • Page 24 FRONT & REAR SHOCK ASSEMBLY HLNA0408 HLNA0332 HLNA0331 HLNA0333 HLNA0409 HLNA0408 HLNA0332 HLNA0331 HLNA0410 HLNA0331...
  • Page 25: Replacement Parts List

    1/10th SCALE 2WD MONSTER TRUCK REPLACEMENT PARTS LIST HLNA0093 ...Dog Bone Set, Front (DSC-2, DTR) HLNA0646 ...Servo Mount Set, (Ion MT) HLNA0101 ...Outdrives Diff, F-R (10-US, ION) HLNA0647 ...Battery Strap Set, (Ion MT) HLNA0130 ...Set Screws (SHSS), M3x3mm HLNA0648 ...Rodend/Turnbuckle Set, Front, (Ion MT, SCT) HLNA0139 ...Body Clips, Small HLNA0649 ...Gasket Set, Receiver Box, (Ion MT) HLNA0140 ...Body Clips, Large...
  • Page 26: Option Parts List

    OPTION PARTS LIST RDNA0230 ..Pinion Gear, 48P, Steel 30T HLNA0350 ...Pinion Gear, 20T, 48P HLNA0356 ...Spur Gear, 84T 48P RDNA0231...Pinion Gear, 48P, Steel 31T RDNA0038 ..Origin LED NiMH 4A Charger (US) RDNA0232 ..Pinion Gear, 48P, Steel 32T RDNA0039 ..Origin LED NiMH 4A Charger (UK) RDNA0233 ..Pinion Gear, 48P, Steel 33T RDNA0040 ..Origin LED NiMH 4A Charger (EU) RDNA0234 ..Pinion Gear, 48P, Steel 34T...
  • Page 27 1/10th SCALE 2WD MONSTER TRUCK NOTES...
  • Page 28 000610-001 (REV A) HLNA0730...

This manual is also suitable for:

Intrusion xlr hlna0685

Table of Contents