Greenstar Heatslave Series Horizontal; Oilfit Flexible Flue Liner - Worcester Greenstar Heatslave 12/18 Technical Information

Greenstar Heatslave series
horizontal fluing options (external models)
Horizontal RS flue
Low level horizontal BF kit
Comprises:
1 x terminal assembly
Part No. 7 716 190 052
Accessories
Worcester Part No.
125mm dia.
90º Bend 7 716 190 034
Flue Terminal Guard 7 716 190 050
Option 1
Low-level rear
240mm
175mm
TOP VIEW
FRONT
Flue components required
Flue Diameter Description Quantity Worcester Part No.
Greenstar Heatslave External models
125mm Standard Flue Kit 1 7 716 190 052
80/125mm Flue Terminal Guard 1 7 716 190 050
Option 2
Low-level left
175mm
TOP VIEW
240mm
FRONT
Flue components required
Flue Diameter Description Quantity Worcester Part No.
Greenstar Heatslave External models
125mm Standard Flue Kit 1 7 716 190 052
80/125mm 90º Bend 1 7 716 190 034
80/125mm Flue Terminal Guard 1 7 716 190 050
N.B. For left and right hand flue termination, a 90º bend is required.
22
Option 3
Low-level right
175mm
TOP VIEW
240mm
FRONT
Flue components required
Flue Diameter Description Quantity Worcester Part No.
Greenstar Heatslave External models
125mm Standard Flue Kit 1 7 716 190 052
125mm 90º Bend 1 7 716 190 034
80/125mm Flue Terminal Guard 1 7 716 190 050
N.B. For left and right hand flue termination, a 90º bend is required.

Oilfit flexible flue liner

Conventional vertical flue kit
100mm dia. conventional vertical flue kit –
Comprises:
1 x adaptor (80mm dia. to 100mm dia.)
1 x adaptor (80mm dia. to 103mm dia.) –
not required for the flexible flue liner installation
1 x bend
1 x bolt and solvent-free grease sachet
1 x air inlet silencer (Greenstar Camray series only)
1 x support bracket
Part No. 7 716 190 036
Accessories
Worcester Part No.
100mm dia.
1,000mm extension kit 7 716 190 066
500mm extension kit 7 716 190 067
Telescopic extension 7 716 190 068
45º bend 7 716 190 069
Wall cover plate kit 7 716 190 074
Spare seal 8 716 110 299 0
Conventional flexible flue liner kit
100mm dia. Oilfit flexible flue liner kit –
Comprises:
1 x chimney cowl
1 x terminal
1 x support collar
1 x support bracket assembly
1 x centralising spacer
1 x flexible to rigid adaptor kit (includes liner & seal)
1 x flexible liner
1 x rigid to flexible adaptor kit (includes liner & seal)
Part No. 7 716 190 076 (8m)
Part No. 7 716 190 077 (12m)
Part No. 7 716 190 078 (15m)
Typical installations
Open (conventional) flued appliances must not be installed
in a bedroom, bathroom or bed-sitting room.
Before installation commences it must be checked that:
•
The chimney is structurally sound and free of obstructions
•
The chimney has been thoroughly swept to remove
deposits since it was last used.
The flexible flue pipe is only suitable for lining chimneys that
conform to the Building Regulations and it should not be
used as a chimney on its own or outside a masonry or
flueblock chimney.
All the flexible liner and adaptors must be within the
chimney with rigid stainless steel flue pipe connecting to the
boiler.
The first 600mm of the stainless steel flue pipe off the
boiler must be vertical with no bends or restrictions.
There must be at least a 25mm clearance between the S/S
flue pipe and any combustible material.
The data label must be secured onto the chimney or chimney
hearth using the plate provided.
If it is not possible to attach the plate to the chimney, the
plate can be attached, in a visible position, next to the
electricity consumer unit.
Do not attach the data plate or label to the flue system.
The terminal should not be modified and an extra cowl or
cover must not be fitted, the boiler is designed so that any
rain that enters the flue will be directed down to the
condensate drain.
23