Sony HCD-FX999W Service Manual page 25

QQ
3 7 63 1515 0
(23) Push A button to eject tray.
(24) Remove Test Disc YEDS-18 from tray.
(25) Push A button to close tray.
(26) Press 0 "R" button to the Drive Manual Operation menu.
(27) Press 0 "R" button to return to the Remocon Diagnosis
Menu.
(28) Press the ?/1 button to switch OFF set.
(22) Confirm the same values are displayed. If it is not the
same, return to step 15.
MIRR time Adjust Menu
1. CD MIRR time check: YY YY
2. DVD MIRR time check: XX XX
3. Threshold:
4. Save to EEPROM:
5. Default set MIRR time:
[Open] Tray open [close] Tray close
[0] Return to previous menu
(23) Push A button to eject tray.
(24) Remove Test Disc YEDS-18 from tray.
(25) Push A button to close tray.
TE
L 13942296513
(26) Press 0 "R" button to the Drive Manual Operation menu.
(27) Press 0 "R" button to return to the Remocon Diagnosis
Menu.
(28) Press the ?/1 button to switch OFF set.
4-5. EXECUTING IOP MEASUREMENT
In order to execute mirror time adjustment, the following standard
procedures must be followed.
(1) In standby mode, press three buttons x , A and
VOLUME + simultaneously.
Remocon Diagnosis Menu
0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History Check
4. Version information
5. Video Level Adjustment
Model
IF-con Ver
Syscon Ver : X.XX
*1 In HCD-FX999W, "GC7GW***" is displayed.
www
.
http://www.xiaoyu163.com
1
*
: GC7GHW XX
: XX.XX (XXXX)
x ao
y
i
http://www.xiaoyu163.com
8
(2) Select "2. Drive Manual Operation" by pressing the 2 "R"
button on the remote commander. The screen will appear as
below.
1. Servo Control
2. Track/Layer Jump
3. Manual Adjustment
4. Tray Aging Mode
5. MIRR time adjust
0. Return to top Menu
(3) Select "3. Manual Adjustment" by pressing the 3 "R" button
on the remote commander. The screen will appear as below.
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eg boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
o O Change Value
[RETURN] Return to previous menu
Q Q (4) Select Iop by pressing 6 "R" button on the remote commander.
3 6 7 1 3
(5) Wait until a hexadecimal number appear.
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop. ED 9E:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
Change Value
[0] Return to previous menu
(6) Convert each data from hexadecimal to decimal using
conversion table.
(7) Substract between these two values.
(8) If the remainder is smaller than 93 (decimal), then it is
OK. However if the value is higher than 93, then the BU
is defective and need to be change.
(9) Press ORETURN "R" button to return back to previous
menu.
(10) Press 0 "R" button to return to Top Menu and power OFF
the DVD Player.
u163
.
HCD-FX999W/FX1000W
2 9 9 4 2 8
Drive Manual Operation
Manual Adjust
1 5 0 5 8 2 9 9 4
Manual Adjust
m
co
Ver. 1.1
9 9
2 8 9 9
25