Audio Settings - Kenwood KMM-102 Instruction Manual

AUDIO SETTINGS

While listening to any source...
1
Press AUD to enter [AUDIO CONTROL] directly.
2
Turn the volume knob to select an item (see the following table), then
press the knob.
3 2
Repeat step until the desired item is selected or activated.
4
Press and hold to exit.
(or using RC-406)
1
Press AUD to enter [AUDIO CONTROL].
Press J / K to select an item, then press
2
To return to the previous setting item, press
SUB-W LEVEL –15 to +15 (0)
BASS LEVEL –8 to +8 (+2)
MID LEVEL –8 to +8 (+1)
TRE LEVEL –8 to +8 (+1)
EQ PRO (This setting is stored to [USER].)
BASS ADJUST BASS CTR FRQ 60/ 80/ 100/ 200: Selects the center frequency.
BASS LEVEL –8 to +8 (+2): Adjusts the level.
BASS Q FACTOR 1.00/ 1.25/ 1.50/ 2.00: Adjusts the quality factor.
BASS EXTEND ON: Turns on the extended bass. ; OFF: Cancels.
MID ADJUST MID CTR FRQ 0.5K/ 1.0K/ 1.5K/ 2.5K: Selects the center frequency.
MID LEVEL –8 to +8 (+1): Adjusts the level.
MID Q FACTOR 0.75/ 1.00/ 1.25: Adjusts the quality factor.
TRE ADJUST TRE CTR FRQ 10.0K/ 12.5K/ 15.0K/ 17.5K: Selects the center frequency.
TRE LEVEL –8 to +8 (+1): Adjusts the level.
.
.
Adjusts the subwoofer output level.
Adjusts the level to memorize for each source. (Before
making an adjustment, select the source you want to
adjust.)
PRESET EQ
BASS BOOST
LOUDNESS
SUBWOOFER SET
Default: XX
LPF SUBWOOFER THROUGH: All signals are sent to the subwoofer. ; 85HZ/ 120HZ/
SUB-W PHASE
FADER
BALANCE
VOLUME OFFSET
SOUND RECNSTR
(Sound
reconstruction)
• [SUB-W LEVEL]/ [SUBWOOFER SET]/ [LPF SUBWOOFER]/ [SUB-W PHASE] is
selectable only if [SWITCH PREOUT] is set to [SUB-W]. ( 4)
• [SUB-W LEVEL]/ [LPF SUBWOOFER]/ [SUB-W PHASE] is selectable only if
[SUBWOOFER SET] is set to [ON].
DRIVE EQ/ TOP40/ POWERFUL/ ROCK/ POPS/ EASY/ JAZZ/
NATURAL/ USER: Selects a preset equalizer suitable to the music
genre. (Select [USER] to use the settings made in [EQ PRO].)
[DRIVE EQ] is a preset equalizer that reduces noise outside the car or
running noise of the tyres.
LV1/ LV2/ LV3: Selects your preferred bass boost level. ;
OFF: Cancels.
LV1/ LV2: Selects your preferred low and high frequencies boost to
produce a well-balanced sound at a low volume level. ; OFF: Cancels.
ON: Turns on the subwoofer output. ; OFF: Cancels.
160HZ: Audio signals with frequencies lower than 85 Hz/ 120 Hz/
160 Hz are sent to the subwoofer.
REVERSE (180°)/ NORMAL (0°): Selects the phase of the subwoofer
output to be in line with the speaker output for optimum
performance. (Selectable only if a setting other than [THROUGH] is
selected for [LPF SUBWOOFER].)
R15 to F15 (0): Adjusts the rear and front speaker output balance.
L15 to R15 (0): Adjusts the left and right speaker output balance.
For AUX: –8 to +8 (0) ; For other sources: –8 to 0: Preset the initial
volume level of each source. (Before adjustment, select the source
you want to adjust.)
ON: Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are
lost in audio data compression. ; OFF: Cancels.
11
ENGLISH