KitchenAid KEBK171SSS Technical Education page 55

Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
FAILURE ERROR
(Leftmost (Rightmost
2 Clock 2 Clock
SUGGESTED CORRECTIVE ACTION PROCEDURE
Digits) Digits)
KEYPAD DISCONNECTED
E0
F2
Keypad E1 STUCK OR SHORTED KEY
PROCEDURE: Before proceeding, press OFF, OFF, START to enter the Diagnostic
mode and verify the error codes.
A. Unplug oven or disconnect power.
B. Check keypad connector for firm connection.
C. Replace all parts and panels before operating.
D. Plug in oven or reconnect power.
E. If error code returns after 60 seconds proceed to step F.
F. Unplug oven or disconnect power.
G. Replace keypad.
H. Replace all parts and panels before operating.
I. Plug in oven or reconnect power. Wait 60 seconds.
J. If error code returns after 60 seconds, proceed to step K.
K. Unplug oven or disconnect power.
L. Replace cable connecting user interface and keypad.
M. Replace all parts and panels before operating.
N. Plug in oven or reconnect power. Wait 60 seconds.
O. If error code returns after 60 seconds, proceed to step P.
P. Unplug oven or disconnect power.
Q. Replace oven user interface.
R. Replace all parts and panels before operating.
S. Plug in oven or reconnect power. Wait 60 seconds.
T. Verify operation is normal. Press OFF, OFF, START to reenter the Diagnostic
mode and complete checks.
MESSAGE/DESCRIPTION
WARNING
Electrical Shock Hazard
FAILURE ERROR
(Leftmost (Rightmost
2 Clock 2 Clock
Digits) Digits)
E0
F3
Sensors E3
PROCEDURE: Before proceeding, press OFF, OFF, START to enter the Diagnostic
mode and verify the error codes.
A. Verify in Diagnostics temperature reading on sensor.
B. If dashes appear in main temperature display proceed to step C.
C. Unplug oven or disconnect power.
D. Remove back panels and ensure the indicated temperature sensor is plugged
in properly and fully inserted. If not, plug in the connector and proceed to step J.
If sensor is plugged in properly proceed to step E.
E. Check connector P2 on the appliance manager. Ensure P2 connector is
plugged in properly and fully inserted. If connector is inserted properly go to
step J. If not proceed to step F.
F. Visually inspect the wires between P2 on the appliance manager and the
indicated temperature sensor. Make sure the wires are not pinched or cut. If
wires appear intact, unplug P2 connector on the appliance manager.
Go to step G.
G. Measure the indicated sensor resistance value (measure between appropriate
P2 connector pins). For the following sensors, the resistance value should read:
Main Oven Sensor
Meat Probe Sensor
If indicated temperature sensor does not meet these requirements proceed to
step H.
If indicated temperature sensor does meet these requirements proceed
to step J.
H. For MAIN sensor:
Replace appropriate temperature sensor. Repeat step G.
If the requirements are not met, replace sensor harness. Repeat step G.
If the requirements are still not met, replace the meat probe jack.
Repeat step G.
If the meat probe sensor is still not operating correctly go to step I.
I. Replace the appliance manager. Ensure all connectors are properly placed and
firmly connected.
J. Replace all parts and panels before operating.
K. Plug in oven or reconnect power. Wait 60 seconds.
L. Enter into Diagnostic mode and read sensor for main oven sensor and meat
probe on immediate display.
E1
F3
Sensors E2
PROCEDURE: Oven is not equipped with this feature. If error occurs, before
proceeding press OFF, OFF, START to enter into Diagnostics mode and verify the
error codes. If error code returns, replace user interface with correct control
associated with this product.
6-3
MESSAGE/DESCRIPTION
SUGGESTED CORRECTIVE ACTION PROCEDURE
MAIN OVEN SENSOR SHORTED OR OPEN
MEAT PROBE SHORTED
Between 931 and 2869 Ω.
(Approx. 1080 Ω at room temp.)
Between 1,300 and 103,000 Ω.
(Approx. 59,000 Ω at room temp.)
(Insert meat probe into meat probe jack located
inside the oven cavity prior to reading resistance.)
LOWER MAIN OVEN SENSOR SHORTED OR OPEN
WARMING DRAWER SENSOR SHORTED