Related Manuals for MicroNet SP5008A
Summary of Contents for MicroNet SP5008A
- Page 1 User’s Manual IP Telephony Gateway Model No.: SP5008A, SP5018A, SP5058A Website: http://www.micronet.info...
- Page 2 About this User’s Manual This User’s Manual gives users basic steps on installation and operation. Please read this manual chapter by chapter. Chapter 1. Introduction Introduce the IP Telephony Gateway to users in terms of feature, appearance, and application. Chapter 2. Startup Help user complete basic configuration.
-
Page 3: Table Of Contents
1. ..Introduction... 4 Key Features ... 4 Physical Description ... 5 2. ..Startup ... 7 Login into the System ... 7 Network Configuration... 9 2.2.1 Static IP ...11 2.2.2 DHCP ... 12 2.2.3 PPPoE... 13 2.2.4 LAN Setting ... 14 General configuration ... - Page 4 3.3.4 Reset to Default... 58 3.3.5 Network Status ... 59 3.3.6 Version Info..60 3.3.7 Port Status... 61 3.3.8 Password... 62 Rebooting the system... 63 4. ..Operation... 64 Peer to Peer mode (FXO to FXS)... 64 Peer to Peer mode (FXS to FXS) ... 68 5.
-
Page 5: Introduction
1. Introduction Micronet SP5008A / SP5018A / SP5058A are high-capacity SIP Gateway Series that provides 8 FXS / 4 FXS + 4 FXO / 8 FXO ports, and suit to build an IP-based communication platform with other VoIP devices. They meet enterprise’s requirement for functionality (VoIP) upgrade and larger scale implementation by interoperating with legacy PABX and IP PBX/Soft-switch. -
Page 6: Physical Description
Blink / Green LAN(1-4) Blink / Green T(1*) On / Orange L(1*) On / Orange SP5008A Front Panel SP5058A Front Panel SP5018A Front Panel Description The Power is on Booting up for self test Gateway reg. fails Gateway reg. successes... - Page 7 SP5008A: FXS = T1 - T8 SP5018A: FXS = T1 - T4, FXO = L1 - L4 SP5058A: FXO = L1 - L8 SP5008A SP5058A SP5018A --------------------------------------------------------------------------------------------------- RESET Factory default button. Press and hold for 5 seconds to reset T1-T8 The RJ-11 FXS port 1-8, connects analog phone sets, trunk line in PABX.
-
Page 8: Startup
2. Startup 2.1 Login into the System First of all, connect your computer to MICRONET SP5008A / SP5018A / SP5058A’s LAN port by using DHCP. The IP address assign to your computer should be 192.168.123.x by default. Once you can get the IP address from MICRONET SP5008A / SP5018A / SP5058A, you can start the configuration as below. -
Page 10: Network Configuration
2.2 Network Configuration By default, the gateway is in NAT mode (router mode) and can share Internet access with PCs. Go to [ Network Configuration / WAN Setting WAN setting according to actual condition. In default IP type of DHCP client, it requests necessary IP information from your ISP automatically. - Page 11 WAN Setting Item Description Connected mode Select the connection method for the WAN port of the SP5008A/SP5018A/SP5058A, you can choose the following: Static IP DHCP PPPoE Current IP Address Show current IP address DNS server mode Select the DNS behavior, you can...
-
Page 12: Static Ip
Item Description Default gateway Specify the IP address of the default gateway. Remote access Restricts/Blocks users connecting to restriction the WAN port’s IP remotely, you can Enable/Disable this option. PPPoE userID Specify the username of the PPPoE account PPPoE password Specify the password associated to the PPPoE account above. -
Page 13: Dhcp
Press the “Reboot” button to apply the changes. 2.2.2 DHCP Press the “Apply” button (at the bottom) after you finish to save changes. Press the “Reboot” button to apply the changes. ----------------------------------------------------------------------------------------------------- Note: When you are using DHCP in WAN and not connected, please make sure you connect Ethernet before use PC to connect to LAN port. -
Page 14: Pppoe
2.2.3 PPPoE Input PPPoE user ID and password Press the “Apply” button (at the bottom) after you finish to save changes. Press the “CANCEL” button (next to the Apply button) to clear the values in the page. Press the “Reboot” button to apply the changes. -
Page 15: Lan Setting
DHCP server IP address from IP address to Description Specify the IP address of the SP5008A / SP5018A / SP5058A LAN port. Specify the mask address for SP5008A / SP5018A / SP5058A LAN port. Enable/Disable DHCP function on the LAN port. - Page 16 ITEM Domain Name Lease time(sec) DNS server mode Primary DNS address Secondary DNS address Press the “Apply” button (at the bottom) after you finish to save changes. Press the “Reboot” button to apply the changes. Description You can specify the domain name that will be assigned by the DHCP server to the attached network devices.
-
Page 17: General Configuration
When VOIP call is failed to be called out such as register fail or network issue, the call will be route to FXO as backup. When MICRONET SP5008A / SP5018A / SP5058A is malfunction or power failure, the all call will be directly bypassed to FXO. - Page 18 Primary FXS SIP settings FXO Dialing Prefix 3.3.2.1 When you have multiple SIP accounts for each FXS line, please set Representative Number Only to No. Then refer to 3.3.2.1 for the detail When the prefix is set here, the call will be route to FXO instead of VOIP.
-
Page 19: Sip Setting
2.3.2 SIP Setting Primary proxy/P2P IP Secondary proxy Outbound proxy Secondary Outbound proxy Representative Number Enable Specify the data of primary proxy : Enable/Disable, IP address, Port#, Domain Name, Expire time and MWI TTL. The P2P mode will be explained in paragraph Specify the data of secondary proxy: Enable/Disable, IP address, Port#, Domain Name, Expire time and MWI TTL. - Page 20 Account Number Password Display name Forward Forward Number Ring Type Ring Time (s) for Serial ring Status Priority Enter the IP address and port number of the SIP proxy into the Primary proxy address and Port fields. Press the “Apply” button to save changes. Press the “Reboot”...
-
Page 21: Web Administration
MICRONET SP5008A/SP5018A/SP5058A. Select the session refresh method that will be used on the MICRONET SP5008A/SP5018A/SP5058A, you can choose among the two methods: Select who will perform the refreshes, you can choose... - Page 22 Specify the timeout period for SIP Invite messages. For example, if the timeout period is 10 seconds, when the SP5008A / SP5018A / SP5058A sends an Invite message and does not receive a response within 10 seconds, it will cancel the call.
-
Page 23: Payload Type Setting
3.1.2 Payload Type Setting RFC2833 payload type T.38 FAX payload type T.38 Redundancy payload type T.30 FAX by pass payload type Modem by pass payload type Modem relay payload type Specify the RFC2833 payload type (range is 96~128, however 100, 102~105 is reserved by other payload types). - Page 24 Press the “Apply” button (at the bottom) after you finish to save changes. Press the “Reboot” button to apply the changes.
-
Page 25: Line Setting
3.1.3 Line Setting... - Page 26 No Answer Forward Time (FXS only) Line1~Line8 relevant data Type Displays the port type of that particular line. Enable Enable the line or not Register or Unregister to SIP Proxy Number Displays the line numbers that specified in SIP Setting. Account: Input the SIP Proxy registration account ID.
- Page 27 Press the “Apply” button (at the bottom) after you finish to save changes. Press the “Reboot” button to apply the changes.
-
Page 28: Qos Setting
3.1.4 Qos Setting Type Differentiated Services Code Point Setting (DSCP) DSCP RTP DSCP Signal ToS Setting ToS RTP ToS Signal Press the “Apply” button (at the bottom) after you finish to save changes. Press the “Reboot” button to apply the changes. Select Qos Type: DSCP or ToS Select the DSCP value for RTP (voice packets), the value in the drop down list is expressed in binary... -
Page 29: Speed Dial Setting
3.1.5 Speed Dial Setting Speed Dial Specify the speed Dial Number/Telephone Number/Name, Speed Dial Editor then press the Add or Del button to add or delete record... -
Page 30: Peer To Peer Call
Peer to Peer call You can use speed dial to do the peer to peer call as follows: Speed Dial Editor (In P2P application) Specify the speed Dial Number/Telephone Number/Name, then press the Add or Del button to add or delete record The format of “Telephone Number”... -
Page 31: Caller Id Setting
3.1.6 Caller ID Setting Caller ID Setting (Line 1~Line 8) DTMF Caller ID Start Symbol DTMF Caller ID End Symbol Select the (Line 1~Line 8)Caller ID generation type to use, you can choose the following: Disable DTMF FSK(Bellcore) ETSI(Before Ring) ETSI(Between ring) FXO only choose Enable/Disable the caller ID detection... - Page 32 Press the “Apply” button (at the bottom) after you finish to save changes. Press the “Reboot” button to apply the changes. The default symbol is C.
-
Page 33: Cdr Setting
To receive the SYSLOG CDR, you need to have a syslog server to collect the CDR from MICRONET SP5008A / SP5018A / SP5058A. The following is a tool you can be used for testing purpose which can be downloaded from http://tftpd32.jounin.net/. -
Page 35: Syslog Setting
3.1.8 Syslog Setting This syslog is used to send the debug log from MICRONET SP5008A / SP5018A / SP5058A to syslog server. Syslog mode Syslog Server address Syslog Server port Press the “Apply” button (at the bottom) after you finish to save changes. -
Page 37: Advanced Configuration
3.2 Advanced Configuration 3.2.1 System setting prack ROH (FXS only) Send billing signal (FXS only) T.38 NoAttribute FAX redundancy depth T.38 FAX Type PRACK is defined in RFC 3262: Reliability of Provisional Responses in SIP. You can accommodate your softswitch (Proxy Server) to Enable or Disable this feature. - Page 38 T.30 FAXByPass Codec Flash key function (FXS only) Keypad DTMF type End of dial key DTMF Detection Sensitivity Dial Wait Timeout (1~60sec) Inter Digits Timeout (1~5sec) FAXByPass Keyword FAXByPass Keyword IP Address announcement Auto Select the FAX ByPass Codec to use, you can choose the following: G.711 a-law G.711 u-law...
- Page 39 The default range is 10~600sec. Specify the duration (100~1000ms) of loop current drop, 0 for disable. This feature is used when the SP5008A (FXS) are connected with answering machines. When the remote site disconnects, the system will drop FXS port’s voltage to 0, and make the answering machines disconnect.
- Page 40 ping ip to keep alive network ping timer(sec) Press the “Apply” button (at the bottom) after you finish to save changes. Press the “Reboot” button to apply the changes. The default setting is “Disable”, if you are not using this particular special application mentioned above, please do not enable this function.
-
Page 41: Sntp Setting
3.2.2 SNTP Setting SNTP mode SNTP server address Time Zone -GMT Time setting Press the “Apply” button (at the bottom) after you finish to save changes. Press the “Reboot” button to apply the changes. Select the SNTP mode : On or Off Specify the SNTP server address for time synchronization. -
Page 42: Codec Setting
3.2.3 Codec Setting Codec Priority Codec Packet Size Bandwidth Required Press the “Apply” button (at the bottom) after you finish to save changes. Press the “Reboot” button to apply the changes. You can specify the priority of the codec from First to Fifth (first being the highest priority and Fifth being the lowest). -
Page 43: Voice Setting
3.2.4 Voice Setting Jitter Buffer Minimal Delay Maximal Delay OPTFactor Echo cancellation Local voice volume Remote receive volume DTMF volume Specify the minimal delay of the jitter buffer. The range is 0~150 ms and the default setting is 0 ms. Specify the maximal delay of the jitter buffer. - Page 44 You can set this option for each of the 8 lines. 1. Press the “Apply” button (at the bottom) after you finish to save changes. 2. Press the “Reboot” button to apply the changes.
-
Page 45: Tone Setting
3.2.5 Tone Setting Dial tone Ringback tone (FXS only) Busy tone Call-waiting (FXS only) Voice-Notify (for FXS+PSTN only) ROH Tone (FXS only) Disconnect tone 1 Specify the pattern of the Dial tone, you can adjust the high frequency, low frequency, high level, low level, the On and Off time for tone 1 and 2. - Page 46 Disconnect tone 2 1. Press the “Apply” button (at the bottom) after you finish to save changes. 2. Press the “Reboot” button to apply the changes. NOTE: If the disconnect tone only has single frequency, please set it to low frequency. If the disconnect tone only has single cadence, please set it to Tone 1.
-
Page 47: Phone Setting
3.2.6 Phone Setting Primary Ringing Ringing Frequency Ringing ON Ringing OFF Ringing level Flash low Flash high Secondary Ringing (FXS only) Note: The feature will be enabled automatically when the Min. Digit Count has been enabled and specified. It is used to have different ring cadence when the incoming caller number is shorter than the setting of “Min. - Page 48 Ringing Frequency Ringing ON Ringing OFF Ringing level Min. Digit Count Country Press the “Apply” button (at the bottom) after you finish to save changes. Press the “Reboot” button to apply the changes. Specify the Ringing frequency value. ringing frequency : 15~100 (Unit : Hz) Specify the Ringing ON value.
-
Page 49: Digit Manipulation
3.2.7 Digit Manipulation Digit Manipulation Testing Digit Manipulation Editor This option allows users to test the digit manipulation rule you set. With this option, you can specify whether to add digits to a prefix number or drop a prefix number. For example, if the user sets: First Example Prefix: 02 (matched prefix) - Page 50 FXO Dial Prefix 1. Press the “Apply” button (at the bottom) after you finish to save changes. 2. Press the “Reboot” button to apply the changes. For outgoing call, the default will be made to VOIP. However, if you set the FXO prefix here, the call will be route to FXO instead of VOIP.
-
Page 51: Dial Plan
Leading digit: 02 Total Digit count: 10 If the user dials a 10 digit number with a prefix of 02 (e.g. 0282265699), the MICRONET SP5008A / SP5018A / SP5058A will immediately detect it and dial this number straight away. Second Example... - Page 52 1.Press the “Apply” button (at the bottom) after you finish to save changes. 2.Press the “Reboot” button to apply the changes. Leading digit: 02 Total digit count: 10 If the user set the Function parameter as “Disable”, the call number with a length of 10 digits and a prefix of 02 will proceed as normal.
-
Page 53: Management
3.3 Management 3.3.1 Provision Server Note: If you need this requirement, Please contact MICRONET for availabilities. Provision server Mode Provision server IP address Provision server port Provision cycle time Provision default time Press the “Apply” button (at the bottom) after you finish to save changes. -
Page 54: Save-Reload Setting
3.3.2 Save-Reload setting Export File Import File Press the “Reboot” button to apply the changes. Click the “Export” button to export “user.cfg” data Specify the file path and file name to Import the configure data. -
Page 55: Upgrade Firmware
TFTP/FTP server IP address FTP login Target file name Http Upload Select the connection method to update the MICRONET SP5008A/SP5018A/SP5058A’s firmware, you can choose the following: TFTP Specify the TFTP/FTP server’s IP address. Specify the login username/password for the FTP server. - Page 56 Updating the firmware by FTP 1. Select FTP mode in the drop down list. 2. Key in the IP address, login name, password of your FTP server and specify the correct filename of the firmware. 3. Press the Start button (next to the Target file name text box) to execute the upgrade process.
- Page 57 Make sure that the TFTP program points to the directory of where your firmware is stored. Now, leave the TFTP program running and switch back to the MICRONET SP5008A / SP5018A / SP5058A web configuration interface. 2. Under Device Management => Software Upgrade select TFTP mode in the drop down list.
- Page 58 Note: For consistency, it is recommended to reload default setting every time you update the firmware on the MICRONET SP5008A /SP5018A / SP5058A. However, you will lose all the settings configured on the MICRONET SP5008A / SP5018A / SP5058A except Network configuration. For more details on reload default setting,...
-
Page 59: Reset To Default
3.3.4 Reset to Default Users can restore back to factory default settings using this feature. The password of the account and the network configurations are the things that will not be changed when this feature is executed. -
Page 60: Network Status
3.3.5 Network Status Connection mode Current IP address Subnet mask Default gateway Primary DNS address Second DNS address WAN MAC Displays the current connection mode. Displays the current IP address of the WAN port. Displays the current subnet mask’s IP. Displays the current default gateway’s IP. -
Page 61: Version Info
Displays the current boot version loaded on the MICRONET SP5008A / SP5018A / SP5058A. Displays the current post version loaded on the MICRONET SP5008A / SP5018A / SP5058A. Displays the current application version loaded on the MICRONET SP5008A / SP5018A / SP5058A. -
Page 62: Port Status
3.3.7 Port Status Item Status Port Type Register Proxy Displays the corresponding port number. Displays the status of the port. Displays the port type (FXS,FXO)of the corresponding port number. Displays the registration status of the corresponding port number. if the port Register success it will display “Yes”... -
Page 63: Password
3.3.8 Password Username Current password New password Confirm new password Press the “Apply” button (at the bottom) after you finish to save changes. Press the “Reboot” button to apply the changes. Select the type of user name that you would like to configure the password for, you can choose the following: root user... -
Page 64: Rebooting The System
3.4 Rebooting the system Executing this function will reboot the whole system, when configuration changes are made to the device, it needs to be rebooted for the changes to take effect (see figure below). -
Page 65: Operation
Operation Peer to Peer mode (FXO to FXS) In this application, the distance of PABX extension is not limited. You can use the same PABX in two or more branches. Configuration: 1. Side A (FXO): IP address: 10.1.1.2, number is 2000 to 2008 2. - Page 66 Side A : (SP5058A : IP address 10.1.1.2) General Configuration / Line Setting Line 1~Line 8 (Side A -- FXO) Press the “Apply” button (at the bottom) after you finish to save changes. Press the “Reboot” button to apply the changes. Please refer to the figure shown above, Enable all the line and Disable all the register.
- Page 67 Side B: (MICRONET SP5008A : IP address 10.1.1.3) General Configuration—SIP Setting Primary proxy/P2P IP (Side B) Call number configuration Representative number (Side B) Line 1~Line 8 (Side B) Specify the destination (Side A) IP Address of Peer to Peer mode, and specify the port# with...
- Page 68 Side B: (MICRONET SP5008A: IP address 10.1.1.3) General Configuration / Line Setting Line 1~Line 8 (Side B) Press the “Apply” button (at the bottom) after you finish to save changes. Press the “Reboot” button to apply the changes. Please refer to the figure shown above, Enable all the line and Disable all the register and call waiting.
-
Page 69: Peer To Peer Mode (Fxs To Fxs)
4.2 Peer to Peer mode (FXS to FXS) Peer A—MICRONET SP5008A / SP5018A / SP5058A ( for example the IP address is: 192.168.23.14) Peer B—MICRONET SP5008A / SP5018A / SP5058A ( for example the IP address is: 192.168.23.58) Peer A—MICRONET SP5008A / SP5018A / SP5058A ( for example the IP address... - Page 71 Peer B—MICRONET SP5008A / SP5018A / SP5058A (for example the IP address is: 192.168.23.58)
- Page 72 Primary proxy/P2P IP (Peer A / Peer B) Call number configuration Representative number (Peer A / Peer B) Line 1~Line 8 (Peer A / Peer B) Press the “Apply” button (at the bottom) after you finish to save changes. Press the “Reboot” button to apply the changes. Specify the destination IP Address of Peer to Peer mode, and specify the port# with In this application, we define the Peer to Peer...
-
Page 73: Specification
5. Specification Model SP5008A Standard SIPv2 (RFC 3261): Primary and Secondary Proxy, Primary and Secondary Outbound Proxy POTS Interface 8 FXS Ethernet Port 1 x RJ-45 WAN port of 10/100M 4 x RJ-45 LAN ports of 10/100M Voice Codec: G.711a/mu-law, G.723.1 (6.3K), G.729, G.729.A VAD, CNG, and Silence Suppression Echo Cancellation (G.165 / G.168) - Page 74 Password protected for Admin access authority Networking PPPoE Client, DHCP Client / Server, NAT, SNTP QoS: DiffServ / ToS Management User interface: HTTP and Telnet Firmware upgrade via FTP/TFTP/HTTP/Telnet Auto Provisioning Environment Operating Temperature: 0 – 45 degree C Storage Temperature: 0 – 55 degree C Operating Humidity: 10 to 85% (non-condensing) Storage Humidity: 10 to 95% (non-condensing) Power Supply...
- Page 75 Security HTTP 1.1 basic/digest authentication for WEB access MD5 for SIP authentication (RFC 2069/2617) Password protected for Admin access authority Networking PPPoE Client, DHCP Client / Server, NAT, SNTP QoS: DiffServ / ToS Management User interface: HTTP and Telnet Firmware upgrade via FTP/TFTP/HTTP/Telnet Auto Provisioning Power Supply DC 12V, 3A...
- Page 76 MD5 for SIP authentication (RFC 2069/2617) Password protected for Admin access authority Networking PPPoE Client, DHCP Client / Server, NAT, SNTP QoS: DiffServ / ToS Management User interface: HTTP and Telnet Firmware upgrade via FTP/TFTP/HTTP/Telnet Auto Provisioning Power Supply DC 12V, 3A Environment Operating Temperature: 0 –...
Need help?
Do you have a question about the SP5008A and is the answer not in the manual?
Questions and answers