1. Manuals
  2. Brands
  3. MicroNet Manuals
  4. Gateway
  5. SP5002
  6. User manual

MicroNet SP5002 User Manual

2/4 ports ip telephony gateway, fxs interface
Hide thumbs Also See for SP5002:
Table of Contents

Advertisement

Quick Links

See also: User Manual
User's Manual
SP5002/SP5004
2/4 Ports IP Telephony Gateway, FXS Interface
Website:
http://www.micronet.info/

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SP5002 and is the answer not in the manual?

Questions and answers

Related Manuals for MicroNet SP5002

Summary of Contents for MicroNet SP5002

  • Page 1 User’s Manual SP5002/SP5004 2/4 Ports IP Telephony Gateway, FXS Interface Website: http://www.micronet.info/...

  • Page 2: Table Of Contents

    2.3 Hyper Terminal Setting ..................7 3. Initialize SP5002/5004 ......9 3.1 Gatekeeper Mode .....................9 (a) Before you go: Configure SP5002/5004 Password ........10 (b) Configure SP5002/5004 IP Address............10 (c) Gatekeeper Settings ................11 (d) Save SP5002/5004 Configuration & Reboot SP5002/5004....11 3.2 Peer-to-Peer Mode ..................12...
  • Page 3 4.19 [sdial] command...................32 5. Upgrade SP5002/5004...... 33 TFTP/FTP server....................33 Download Procedure....................33 ANNEX A: TCP/UDP port allocation ... 34...

  • Page 4: Introduction

    1. Introduction SP5002/5004 FXS gateway, which based on ITU-T H.323 v3, provides voice and fax over IP networks. Its simplified operation and configuration features are the most suitable for residential and SOHO application. Just an IP address and 2 phone sets can bring you to Voice over IP world.

  • Page 5: Appearance

    GK : 1. LED light on means SP5002 has successfully registered to Gatekeeper when it is in Gatekeeper Mode. 2. LED flashes means SP5002 is not registered to Gatekeeper when it is in Gatekeeper Mode. 3. Or when SP5002 is in downloading mode, LED should be flash as well.
  • Page 6 PIN 1, 2: Transmit PIN 3, 6: Receive 2. CONSOLE: RS232 console port (DB-9pin male connector) Note: use straight-forward cable to connect to your computer. PINOUTS Pin Name Dir Description Receive Data Transmit Data System Ground 3. TEL1 – TEL2: RJ-11 connector, FXS interface. To connect analog phone sets or trunk line of PABX.

  • Page 7: Start-Up

    (a) Hyper terminal, telnet. (b) Gatekeeper (optional) 2.2 IP Environment Setting Users must prepare a valid IP address, complied with IP Network, for SP5002/5004’s proper operation. For testing the validation of chosen IP address, use same IP configuration in other PC or Notebook, and then try to connect to Public Internet (go to well-known website, receive Internet mail, or ping a specific public IP address).

  • Page 8: Hyper Terminal Setting

    2.3 Hyper Terminal Setting A terminal emulator is needed when using RS-232 port to configure SP5002/5004. There are kinds of terminal emulator software. Here, we use Microsoft HyperTerminal to depict how to set up terminal emulator: 1. Execute the Hyper Terminal program, and then the following windows will pop-up on the screen.
  • Page 9 3. After pressing OK button, the next window appear, and then choose COM1/2 Port, which you are going to use. 4. Configure the COM Port Properties as following: (1) Bits per second: 9600 (2) Flow control: None Press ‘OK’ button, and then start to configure SP5002/5004.

  • Page 10: Initialize Sp5002/5004

    3. Initialize SP5002/5004 3.1 Gatekeeper Mode (a) Configure SP5002/5004 IP Address (b) Gatekeeper Mode Settings (c) Save SP5002/5004 Configuration & Reboot SP5002/5004...

  • Page 11: (A) Before You Go: Configure Sp5002/5004 Password

    Initialize OSS libraries...OK! VP v1.40 stack open sucessfully. login: 2. login: when SP5002/5004 is used for the first time, “root” is default login name without a password. 3. Password setting: type “passwd –set root ****” to define a password for “root”...

  • Page 12: (C) Gatekeeper Settings

    An example is demonstrated below: --------------------------------------------------------------------------------------------------- usr/config$ ifaddr –ip 10.1.1.1 –mask 255.2555.255.0 –gate 10.1.1.254 Note: this is to assign SP5002/5004 an IP address of “10.1.1.1”, subnet mask “255.255.255.0”, and default IP gateway “10.1.1.254”. (c) Gatekeeper Settings 1. To assign a gatekeeper address for SP5002/5004, and define its own registered ID and phone number.

  • Page 13: Peer-To-Peer Mode

    3.2 Peer-to-Peer Mode Peer-to-Peer Mode allows users to call other VoIP devices without using a gatekeeper. When in Peer-To-Peer mode, SP5002/5004 will send SETUP message directly to the destination IP address once the dial is finished. Users have 2 dialing methods.

  • Page 14: Command Lists

    Password setting information and configuration sdial shorten the dialing number manipulation usage: help [command] 4.2 [quit] command Type quit will quit the SP5002/5004 configuration mode. And turn back to login prompt. usr/config$ quit Disconnecting... login: Note: It is recommended that type the “quit” command before you leave the console.

  • Page 15: Debug] Command

    4.3 [debug] command Open debug message will show up specific information while SP5002/5004 is in operation. After executing the debug command, it should execute command debug -open as well. One example is demonstrated below. usr/config$ debug -add h323 vp usr/config$ debug -open...

  • Page 16: Commit] Command

    Note: It is recommended that use “flash –clean” after application firmware id upgraded. Warning: Once users execute flash –clean, all the configurations of SP5002/5004 will be cleaned. This can be executed only by user whose login name is root. 4.6 [commit] command Save changes after configuring SP5002/5004.

  • Page 17: Time] Command

    -sntp 1 10.1.1.1 while 10.1.1.1 stands for SNTP server’s IP address. 4.8 [time] command When SNTP function of SP5002/5004 is enabled and SNTP server can be found as well, type time command to show current network time. -------------------------------------------------------------------------------------------------...

  • Page 18: Pbook] Command

    For example: if 192.168.1.2 is not existing while 210.63.15.32 exists. Users will have the following results: usr/config$ ping 192.168.1.2 no answer from 192.168.1.2 usr/config$ ping 210.63.15.32 210.63.15.32 is alive 4.10 [pbook] command Phone Book function allows users to define their own numbers, which mapping to real IP address.
  • Page 19 1 to 100, to the parameter to show specific phone number. Note: <index number> means the sequence number in phone book. If users do request a specific index number in phone book, SP5002/5004 will give each record a automatic sequence number as index. -add add a new record to phone book.

  • Page 20: Sysconf] Command

    If users want to make a call to PSTN number “82265699”, they have to pickup one of the phone connected to SP5002/5004, and then dial “082265699”. After receiving the complete dialed number, SP5002/5004 will search for its Phone Book, find “0” as matched prefix, and then dial out to B’s IP address directly with destination e.164 (phone number) “82265699”.
  • Page 21 -plan digits (any positive integer) of dial plan. This police is effective for calls from PSTN side. When SP5002/5004 collects the number of pre-defined digits, it will send those digits out automatically. “0” stands for “any number”, which accepts any digit length. When dial plan is set to “0”, users can end the dial with “#”...

  • Page 22: H323] Command

    -gk 210.59.163.171 –prefix 7 -line1 701 -line2 702 Parameters Usage: -print print current h323 related settings -mode alternatives for gatekeeper or peer-to-peer mode (0=gatekeeper mode; 1=peer-to-peer mode). If users select gatekeeper mode, a extra gatekeeper is needed when SP5002/5004 is in operation.
  • Page 23 RTP port range conflicts with Firewall policy. -h245 to specify h.245 port number (not available) -ttl to set timer for TTL(Time To Live). SP5002/5004 would send RRQ, with keepAlive, to gatekeeper periodically according to TTL timer. -gkfind gatekeeper finding port. Port number, which SP5002/5004 uses it to discover a gatekeeper.

  • Page 24: Voice] Command

    4.13 [voice] command The voice command is associated with the audio setting information. There are four voice codecs supported by SP5002/5004. ------------------------------------------------------------------------------------------------ usr/config$ voice Voice codec setting information and configuration Usage: voice [-send [G723 ms] [G711A ms] [G711U ms] [G729 ms] ]...
  • Page 25 -volume There are three adjustable value. voice volume stands for volume, which can be heard from SP5002/5004 side; input gain stands for volume, which the opposite party hears. dtmf volume stands for DTMF volume/level, which sends to its own Line1 or Line2.

  • Page 26: Support] Command

    -tunnel to switch ON/OFF (1 = ON; 0 = OFF) H.245 tunneling function. If the function is ON, SP5002/5004 will send H.245 (Call Control messages) via H.225’s (Call Signal messages) link. The function is effective only when both side support h245 tunnel.

  • Page 27: Tos] Command

    Note: it is not recommended to change the value in this command, only if users do know well the application. This might cause incompatibility with other devices. 4.15 [tos] command TOS service allows users to achieve QoS on IP network. ------------------------------------------------------------------------------------------------- usr/config$ tos IP Packet ToS(type of Service)information and configuration...
  • Page 28 -thruput 0 or 1, while 1 stands for high throughput, and 0 for normal condition. -reliab 0 or 1, while 1 stands for high reliability, and 0 for normal condition. Note: Users should be aware that TOS is effective only when network devices (for ex: router, switch..

  • Page 29: Phone] Command

    4.16 [phone] command SP5002/5004 progress tone is configurable for users. Default tone value is set according to U.S. tone specification. Users should adjust the values according to their own country’s tone specification or users-defined tone specification. --------------------------------------------------------------------------------------------- usr/config$ phone Phone ringing , ringback tone , busy tone , dial tone setting and notes...
  • Page 30 High and Low frequency/level/cadence can be configured respectively. -ring to set RING tone value. The played tone type, when SP5002/5004 is receiving a call. -rbt to set RingBackTone value The played tone type, when SP5002/5004 receives a Q.931 Alerting message.

  • Page 31: Rom] Command

    4.17 [rom] command ROM file information and firmware upgrade function. ------------------------------------------------------------------------------------------------ usr/config$ rom ROM file updating commands Usage: rom [-print] [-app] [-dsptest] [dspcore] [dspapp] -s TFTP/FTP server ip –f filename rom –print -print show version of ROM files. (optional) -app update main application code.

  • Page 32: Passwd] Command

    4.18 [passwd] command For security concern, users have to input the password before entering configuration mode. “passwd” command is for password setting purpose. ------------------------------------------------------------------------------------------------- usr/config$ passwd Password setting information and configuration Usage: passwd -set Loginname Password passwd -clean Note: 1. Loginname can be only 'root' or 'administrator' 2.

  • Page 33: Sdial] Command

    4.19 [sdial] command SpeedDial information and configuration ------------------------------------------------------------------------------------------------ Usage: sdial [-add [briefNum mappingNum]] sdial [-modify [briefNum mappingNum]] sdial [-delete [briefNum mappingNum]] sdial [-sw enable] sdial [-print] -add Add a record to speedDial table. -modify Modify a exist record. -delete Delete a record from speedDial table. SpeedDial function enable/disable.

  • Page 34: Upgrade Sp5002/5004

    5. Upgrade SP5002/5004 SP5002/5004 supports remote download via TFTP to update with new ROM file. Regarding new version release, please contact local distributor for more information. TFTP/FTP server It is necessary to prepare the TFTP/FTP server program on the host PC as TFTP/FTP server.

  • Page 35: Annex A: Tcp/Udp Port Allocation

    ANNEX A: TCP/UDP port allocation While a complete H.323 communication is established, the following ports are possibly to be used: TCP port: Q.931/H.225 dynamic, but mostly 1025 (gatekeeper mode) 1720 (peer to peer mode) H.245 dynamic, but mostly 1027 (not in use if Fast Start or Tunnel mode is activated) UDP port: adjustable, default = 1024...

This manual is also suitable for:

Sp5004

Table of Contents