RedLeaf RLC-BF2050 Installation Manual

Network Camera

Installation Manual
Before operating the unit
please read this manual
thoroughly and retain it for
future reference.
Box Series
. . . . . . . . . .
FULL HD 5
. . . . . .
1080 M
www.RedLeafSecurity.net
MEGAPIXEL
c 2012 Redleaf Corporation Version 1.1.0
Welcome
Thank you for purchasing our IP camera.
This Quick Reference guide describes how to install
and configure your RedLeaf IP camera.
Before you start to install and use your new camera,
please read these instructions carefully.
Please keep this start guide well for future reference.
Please open the accessory bag to check the items one
by one in accordance with the list below. Contact your
local retailer ASAP if something is missing or damaged
in the bag.
For the most up-to-date information about this product,
visit the official RedLeaf website at
www.redleafsecurity.net
!
Before your operation please read the following
instructions carefully.
1．Electrical safety
All installation and operation here should conform to
your local electrical safety codes.
The power shall conform to the requirement in the SELV
(Safety Extra Low Voltage) and the Limited power
source is rated 12V DC in the IEC60950-1.
!
Please note: Do not connect these two power
supplying sources to the device at the same time; it
may result in device damage!
We assume no liability or responsibility for all the fires or
electrical shock caused by improper handling or
installation.
We are not liable for any problems caused by
unauthorized modification or attempted repair.
2.Transportation security
Heavy stress, violent vibration or water splash are not
allowed during transportation, storage and installation.
3.Installation
Do not apply power to the camera before completing
installation.
Please install the proper power cut-off device during the
installation connection.
Always follow the instruction guide the manufacturer
recommended.
4.Qualified engineers needed
All the examination and repair work should be done by
the qualified service engineers.
We are not liable for any problems caused by
unauthorized modifications or attempted repair.
5.Environment
This series IP camera should be installed in a cool, dry
place away from direct sunlight, inflammable, explosive
substances and etc.
Please keep it away from the electromagnetic radiation
object and environment.
Please make sure the CCD (CMOS) component is out
of the radiation of the laser beam device. Otherwise it
may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the
camera.
Thunder-proof device is recommended to be adopted to
better prevent thunder.
The grounding studs of the product are recommended
to be grounded to further enhance the reliability of the
camera.

6. Daily Maintenance

Please shut down the device and then unplug the power
cable before you begin daily maintenance work.
Do not touch the CCD (CMOS) optic component. You
can use the blower to clean the dust on the lens surface.
Always use the dry soft cloth to clean the device. If
there is too much dust, please use the water to dilute the
mild detergent first and then use it to clean the device.
Finally use the dry cloth to clean the device.
Please put the dust proof cap to protect the CCD
(CMOS) component when you do not use the camera.
7. Accessories
Be sure to use all the accessories recommended by
manufacturer.
Before installation, please open the package and check
all the components are included.
Contact your local retailer ASAP if something is broken
in your package.
Amount
Accessory Name
IPC Unit
1
C/CS adapter
1
Quick Start Guide
1
CD
1
Framework
1 FrameWork
1.1 Rear Panel
This series IP camera real panel is shown as below. See
- Figure 1-1.
Figure 1-1 The rear panel with the network port
For fiber input See - Figure 1-2
. . . . . . . . . .
8
. . . . . .
M
MEGAPIXEL
Figure 1-2 The rear panel with the 100M fiber port
Please refer to the following sheet for detailed
information.
Connector
Interface Name / Description
Video BNC
VIDEO OUT
output
port
AC 24V/ DC
Power Port.
12V
STATUS Red light
indication
light
IN
Alarm
I/O port
input port
NO
Alarm
C Output
port
G GND
A Rs485
port
b
RX Rs232
port
TX
GND
G
IR light
NA
port
RESET RESET
button
Framework
Audio
AUDIO OUT
output
port.
Audio
AUDIO IN
input
port.
Network
LAN
port
OPT 100M
fiber port
SD SD card
port
Function
Output analog
GND
video signal. can
connect to TV
monitor to view
video
1-3 Side panel
Power Port.
Please refer to the following interface for side panel
Input 12V DC
or AC 24V
dimension information. The unit is mm. See - Figure
1-3.
System boot
up-red light
is on
system
upgrades-red
light flashes
System
resets-red
light flashes
Figure 1-3
Normal
working
status-green

1-4 Front Panel

light is on. Please refer to the following interface for the front
Display
panel information. The unit is mm. See -Figure 1-4.
record
status: record
-green light
flashes
Detect the
wireless
device-yellow
light
is on
Alarm input port
to receive the
signal from the
Installation
external alarm
device.
2-1 Lens installation
Alarm output port.
2-1-1 Auto Aperture Lens
Please follow the steps listed below for auto
To output alarm
aperture lens installation. See figure 2-1 and 2-2.
signal to the
- Remove the CCD protection cap of the
alarm device.
device, and then line up the lens to the proper
No: Normal
installation position. Turn clockwise until the
open alarm
lens is fixed firmly.
output end.
- Insert the lens cable socket to the auto lens
C: alarm
connector in the side panel.
output public
end.
Alarm input
ground end
RS485_A port,
control external
PTZ
RS485_B port,
control external
PTZ
RS232_RX ,
Rs232 receive
Figure 2-1
end.
RS232_TX ,
Rs232 COM send
out end.
Rs232 ground
end
External IR light
signal control port
Restore factory
Figure 2-2
default setup.
when system is

2-1-2 Manual Lens

running normally
Install C type lens:
press the RESET
button for at least
5seconds,
- Remove the CCD protection cap from the
system can
device.
restore factory
- Install the C/CS adapter to the camera. Turn
default setup.
clockwise to secure against the focusing ring
firmly.
- Line up the C lens to the installation position
of the C/CS adapter. Turn clockwise to fix the
lens.
- Use slotted screwdriver to fasten the screw
near the focusing ring and then turn counter
output audio
Audio
clockwise to move the focusing ring out for
signal to the
output
several millimeters. Now you can focus
3.5mn passive device
such az earphone.
JACK
manually and check the video is clear or not.
port.
If you can not see the clear video, you can
input audio signal
Audio
adjust via the flange-back.
from device such
input
3.5mn as pick-up. - After you completed the focus setup, use the
JACK
slotted screwdriver to fix the screw firmly.
port.
Fasten the focusing ring. Now the installation
connect to
completed.
Etherne
standard
t port
Ethernet
2-1-3
cable.
support poE
- Remove the image sensor protection cap
function.
from the device.
- Line up the CS lens to the lens installation
position of camera focusing ring. Turn
clockwise to fix the lens.
155M Transmit 100M
- Use slotted screwdriver to fasten the screw
signal Ethernet data. near the focusing ring and then turn counter
fiber clockwise to move the focusing ring out for
several millimeters. Now you can focus
dual-
direction manually and check the video is clear or not.
If you can not see the clear video, you can
Connect to SD adjust via the flange-back.
card.
- After you completed the focus setup, use the
Note: When you
slotted screwdriver to fix the screw firmly.
install the SD
card, please Fasten the focusing ring. Now the installation
make sure
completed.
current card
is not in write
mode and
then you can
install it to
the camera.
When you
remove the
SD card ,
please make
sure current
card is not in
write mode.
otherwise it
may result in
data loss or

2-1-4 Remove Lens

card damage.
Please follow the steps listed below to remove lens.
Before hot
The interface is shown as in - Figure 2-1.
swap, please
stop record
- Turn the lens counter clockwise and then
operation
remove it from the camera.
- Unplug the auto lens cable socket from the
please make sure
the device is auto lens connector. If you are using the
securely earthed
manual aperture lens, please skip to the
to prevent the
following step.
thunderstorm
strike
- If there is no lens, please put the image
sensor protection cap back to protect the
image sensor.

2-2 SD Card

2-2-1 Installation

Please follow the steps listed below to install SD
card. The interface is shown as in - Figure2-4 and -
Figure 2-5.
- Use the screwdriver to loosen the SD card
protection screw in the rear panel, and then
remove the SD card protection cap from the
camera.
- Install the SD card to the camera according
to the proper installation position.
- Put the SD card protection cap back.
- Use the screwdriver to fix the SD card
protection cap screw firmly to secure the SD
card protection cap in the camera.
Figure1-4

2-2-2 Remove

Please follow the steps listed below to remove SD
card. The interface is shown as -Figure 2-6
- Use the screwdriver to loosen the screw of
SD card protection cap in the rear panel.
Remove the cap from the camera.
- Follow the SD card direction to remove the
SD card.
- Insert the SD card protection cap.
- Use the screwdriver to fix the screw to secure
the protection cap. and -Figure 2-6.
Installation
Install CS type lens
Figure 2-3
Figure 2-4
Figure 2-5
Figure 2-6