RedLeaf RLC-BH1420 Installation Manual

Network Camera

Installation Manual
Before operating the unit
please read this manual
thoroughly and retain it for
future reference.
Mini Bullet Series
FULL HD
1080
www.Redleafsecurity.net
c 2012 Redleaf Corporation Version 1.1.0
Welcome
Thank you for purchasing our IP camera.
This Quick Reference guide describes how to install
and configure your RedLeaf IP camera.
Before you start to install and use your new camera,
please read these instructions carefully.
Please keep this start guide well for future reference.
Please open the accessory bag to check the items one
by one in accordance with the list below. Contact your
local retailer ASAP if something is missing or damaged
in the bag.
For the most up-to-date information about this product,
visit the official RedLeaf website at
www.redleafsecurity.net
!
Before your operation please read the following
instructions carefully.
1．Electrical safety
All installation and operation here should conform to
your local electrical safety codes.
The power shall conform to the requirement in the SELV
(Safety Extra Low Voltage) and the Limited power
source is rated 12V DC in the IEC60950-1.
! Please note: Do not connect these two power
supplying sources to the device at the same time; it
may result in device damage!
We assume no liability or responsibility for all the fires or
electrical shock caused by improper handling or
installation.
We are not liable for any problems caused by
unauthorized modification or attempted repair.
Welcome
2．Transportation security
Heavy stress, violent vibration or water splash are not
allowed during transportation, storage and installation.
3．Installation
Do not apply power to the camera before completing
installation.
Please install the proper power cut-off device during the
installation connection.
Always follow the instruction guide the manufacturer
recommended.
4．Qualified engineers needed
All the examination and repair work should be done by
the qualified service engineers.
We are not liable for any problems caused by
unauthorized modifications or attempted repair.
5．Environment
This series IP camera should be installed in a cool, dry
place away from direct sunlight, inflammable, explosive
substances and etc.
Please keep it away from the electromagnetic radiation
object and environment.
Please make sure the CCD (CMOS) component is out
of the radiation of the laser beam device. Otherwise it
may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the
camera.
Thunder-proof device is recommended to be adopted to
better prevent thunder.
The grounding studs of the product are recommended
to be grounded to further enhance the reliability of the
camera.
6. Daily Maintenance
Please shut down the device and then unplug the power
cable before you begin daily maintenance work.
Do not touch the CCD (CMOS) optic component. You
can use the blower to clean the dust on the lens surface.
Always use the dry soft cloth to clean the device. If
there is too much dust, please use the water to dilute the
mild detergent first and then use it to clean the device.
Finally use the dry cloth to clean the device.
Please put the dust proof cap to protect the CCD
(CMOS) component when you do not use the camera.
7. Accessories
Be sure to use all the accessories recommended by
manufacturer.
Before installation, please open the package and check
all the components are included.
Contact your local retailer ASAP if something is broken
in your package.
Accessory Name Amount
RLC Unit 1
Accessories Bag 1
Quick Start Guide 1
Resource CD 1
Framework
1.1 Multiple-function Combination Cable
You can refer to the following figure for multiple-function
combination cable information.
See -Figure 1-1.
Figure 1-1
Please refer to the following sheet for detailed information.
Port Name Function Connection Note
Connect to standard
1. LAN Network Port Ethernet Port
Ethernet cable.
Power input port.
2. DC 12V Power input
/
Input DC 12V
port
1.2 Framework and Dimension
Please refer to the following figure for dimension
information. The unit is mm.
See -Figure 1-2 and -Figure 1-3.
165
Figure 1-2
70
Figure 1-3
Device Installation
Please follow the steps listed below to install the device.
Please refer to - Figure 2-1 and Figure 2-2 for
reference.
Paste the installation map on the surface of the
wall or the ceiling.
Dig the installation holes according to the
installation map.
Open the accessories bag and then take the
expansion bolt out. Insert the expansion bolt
into the installation holes.
Take the screws from the accessories bag and
then use them to secure the device on the
installation surface of the wall or the ceiling.
Connect the corresponding cables.
No. Name
1. IPC Unit
2. Installation Screw
3. Expansion Bolt
4. Installation Map
5. Ceiling or Wall
Figure 2-1
 Use the cross-head screwdriver to loosen the
adjust screw.
Turn the device in different directions to make

it suitable for the monitor position.
 Use the cross-head screwdriver to fix the
adjust screw firmly. See Figure 2-2.
Figure 2-2