Operating Instructions; Installation; Start-Up And Use - Hotpoint ENBLH 19xxx FW O3 Operating Instructions Manual

Installation

! Before placing your new appliance into operation please read these
operating instructions carefully. They contain important information for
safe use, for installation and for care of the appliance.
! Please keep these operating instructions for future reference.
Pass them on to possible new owners of the appliance.
Positioning and connection
Positioning
1. Place the appliance in a well-ventilated humidity-free room.
2. Do not obstruct the rear fan grills. The compressor and
condenser give off heat and require good ventilation to operate
correctly and save energy.
3. Leave a space of at least 10 cm between the top part of the
appliance and any furniture above it, and at least 5 cm between
the sides and any furniture/side walls.
4. Ensure the appliance is away from any sources of heat (direct
sunlight, electric stove, etc.).
5. In order to maintain the correct distance between the appliance
and the wall behind it, fit the spacers supplied in the installation
kit, following the instructions provided.
Levelling
1. Install the appliance on a level and rigid floor.
2. If the floor is not perfectly horizontal, adjust the refrigerator by
tightening or loosening the front feet.
Electrical connections
After the appliance has been transported, carefully place it
vertically and wait at least 3 hours before connecting it to the
electricity mains. Before inserting the plug into the electrical socket
ensure the following:
• The appliance is earthed and the plug is compliant with the law.
• The socket can withstand the maximum power of the appliance,
which is indicated on the data plate located on the bottom left
side of the fridge (e.g. 150 W).
• The voltage must be in the range between the values indicated
on the data plate located on the bottom left side (e.g. 220-
240V).
• The socket is compatible with the plug of the appliance. If
the socket is incompatible with the plug, ask an authorised
technician to replace it (see Assistance). Do not use extension
cords or multiple sockets.
! Once the appliance has been installed, the power supply cable
and the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by authorised
technicians only (see Assistance).
! The manufacturer declines any liability should these safety
measures not be observed.

Start-up and use

Starting the appliance
! Before starting the appliance, follow the installation
instructions (see Installation).
! Before connecting the appliance, clean the compartments and
accessories well with lukewarm water and bicarbonate.
! The appliance comes with a motor protection control system which
makes the compressor start approximately 8 minutes after being
switched on. The compressor also starts each time the power supply
is cut off whether voluntarily or involuntarily (blackout).
1. Insert the plug into the socket and switch on the product using
the appropriate button, ensure that yellow refrigerator and
freezer temperature lights illuminates
2. After a few hours you will be able to put food in the refrigerator.
3. Press the SUPER FREEZE button (rapid freezing): the SUPER
FREEZE indicator light will illuminate. Once the refrigerator has
reached the optimal temperature, the indicator light goes out
and you can begin food storage.
Chiller system
NO FROST
The No Frost system circulates cold air continuously to collect
humidity and prevent ice and frost formation. The system maintains
an optimal humidity level in the compartment, preserving the
original quality of the food, preventing the food from sticking
together and making defrosting a thing of the past. Do not
block the aeration cells by placing food or containers near the
refrigerating back panel.
! Close bottles and wrap food tightly.
ACTIVE OXIGEN
This device releases ozone molecules inside the refrigerator;
ozone is a natural substance which combats bacteria and
microorganisms, reducing their proliferation while limiting
unpleasant odours.
Automatically defines the amount of ozone required for prolonging
the freshness of foodstuffs, eliminating odours and preventing
bacteria build-up.
There may be a slight distinctive odour inside the refrigerator.
The very same smell can sometimes be detected during a storm,
due to the ozone produced as the charge in the lightning bolts
is released; this is completely normal. The amount produced by
the device is very small and abates quickly as the antibacterial
action takes place.
Device is activated by pressing the dedicated key on the
dashboard.(blue led)
With the Active Oxigen switched on, the device will operate
a repeted cycle until the key is pressed again. There will be
an Ozone emission noticed by the switching on of the green
led located on the Active Oxigen device located in the fridge
compartment and a stand-by cicle (without zone emission) noticed
by blue light.
GB
21