Download Print this page

Remote Control; Care And Maintenance; Troubleshooting - Electrolux Oxygen EAP150 Instruction Book

Hide thumbs

Advertisement

Table of Contents

REMOTE CONTROL

EAP300, EAP450
Operate the remote control facing the air cleaner.
EN
Operate within 6 metres of the air cleaner.
The remote control has a separate wall-mountable storage
cradle that can be conveniently attached to any wall using
a screw.
S. POWER: Use the power button to turn the power on and
off. A short "beep" will sound when the unit turns on and
off.
T. AUTO Mode: Use the AUTO button to put air cleaner in
AUTO mode.
U. FAN SPEED: By pressing up or down, the unit will
change fan speeds and enter into manual mode.

CARE AND MAINTENANCE

EAP150, EAP300, EAP450
CAUTION: Turn off the unit and unplug the electrical cord
before performing any maintenance.
Clean unit as necessary by wiping with a dry, soft cloth;
for stubborn stains, use a warm, damp cloth.

TROUBLESHOOTING

EAP150, EAP300, EAP450
Occurrence
Can I wash my filter?
Can I vacuum my filter?
There is an odour coming from the unit and
I just opened it.
Will this clean a bigger area than what it is
rated for?
Where should I place the unit?
The AIR QUALITY light is orange or red, but
the air seems clean.
There is still some dust you can see in the air
or on my furniture
There is nothing holding the filters in place
I can hear revving of the fan motor
The unit has stopped removing odours
effectively, or seems to be emitting an
odour.
The CHECK FILTER indicator remains lit after
replacing the HEPA filter.
42
www.electrolux.com
V. TURBO: Use this button to switch from automatic
operation and start the maximum amount of room
air cleaning and air movement. It will remain in Turbo
speed until changed into Auto or manual mode.
Battery replacement
1. Squeeze tabs of battery cover and at the same time pull
cover out of remote.
2. Insert battery as shown and close battery cover.
3. Always use 3V lithium battery CR2025. Incorrect battery
usage may cause battery fluid leakage and/or damage.
Do not use volatile fluids such as benzene, paint thinner
or scouring powder, as they may damage the surface.
Keep the unit dry.
Lightly vacuum air quality sensor every three months.
Possible causes/solution
No, the filters that come with the unit will fall apart and be ruined if water is run
through them. (The Washable Pre Filter and HEPA 13 Filter for model EAP450 can be
washed)
No, vacuuming will only spread the dust back into the air. If you think the filter is too
dirty, it may be time to replace. (The Washable Pre Filter for model EAP450 can be
cleaned with a vacuum cleaner or soft brush)
The unit has been concealed in a tightly wrapped package of currogated cardboard
and plastic. Because this has a fan and pulls air through it, it may give off some "new"
odours. Depending on sensitivity, this should wear off in several days or perhaps a
week depending on how much it is used.
CADR ratings are provided from a controlled testing environment, if that environment
changes, it can affect the performance. However if you have a slightly larger room than
what the CADR rating is, it will still help improve the air, but may take a bit longer to
do so.
Allow proper air circulation around the sides and infront of the unit. If there are doors
or narrow hallways it may reduce the airflow to the air cleaner, but will eventually
circulate near the machine.
Clear the sensor with a vacuum cleaner, as it may be blocked or clogged.
Sometimes a compressed can of air may unclog the dust in the sensor.
The unit will capture most dust and particles, however with opening doors, windows,
central HVAC etc... there may still be some level of dust that you can see.
The filters are meant to rest inside the unit. Once the unit is turned on, the force of air
pulled through the machine will create a tight seal of the filters.
This is normal, especially at night when all environmental sounds are quiet, you may
hear the motor running in repetition.
Make sure the air quality sensor is not blocked or clogged.
Move the unit closer to the offending odours.
Replace the filters as they may have reached their capacity to absorb pollutants. You
may need to replace filters more frequently.
Press the RESET FILTER button by gently inserting a paper-clip into the
RESET FILTER button hole. Hold for 3-5 seconds until a "beep" sounds to
indicate the unit has been reset.

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Oxygen eap300Oxygen eap450