Download Print this page
Saab 32 025 686 Installation Instructions Manual
Saab 32 025 686 Installation Instructions Manual

Saab 32 025 686 Installation Instructions Manual

Saab 2006 9-5 4d

Advertisement

Quick Links

900
SITdefault
Saab 9-5 4D M06-
Parking assistance (SPA)
Accessories Part No.
32 025 686
Important
To install the kit the car must be equipped with
towbar wiring harness provision.
MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS
MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE
Group
9:40-06
SCdefault
Installation instructions
Date
Instruction Part No.
Sep 05
32 025 688
Saab 9-5 4D M06-
Replaces
E930A398

Advertisement

loading
Need help?

Need help?

Do you have a question about the 32 025 686 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Saab 32 025 686

  • Page 1 Installation instructions SCdefault MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE SITdefault Saab 9-5 4D M06- Parking assistance (SPA) Accessories Part No. Group Date Instruction Part No. Replaces 32 025 686 9:40-06 Sep 05 32 025 688 E930A398 Important To install the kit the car must be equipped with towbar wiring harness provision.
  • Page 2 2 Screw (x2) 3 Holder (x4) 4 Distance sensor (x4) 5 Connector bracket 6 Wiring harness, distance sensor 7 SPA wiring harness 8 Connector 9 Cable tie (x17) 10 Cable tie, rubber grommet 11 Rubber grommet Saab 9-5 4D M06-...
  • Page 3 6 Detach and fold aside the right-hand trim in the luggage compartment and remove the insula- tion pads (x2) in the rear of the body. The old ones must be discarded and replaced with new. Saab 9-5 4D M06-...
  • Page 4 13 With help from an assistant, pull the bumper out from the clips. Lift the bumper out backwards. Important Place the bumper on a soft, clean surface. 14 Remove the bumper rail from the protective shell by detaching the retaining clips. Saab 9-5 4D M06-...
  • Page 5 20 Fit the connector's holder to the left-hand side of the bumper rail. 21 Fit the connector in the holder. 22 Fit the cellular block with wiring harness in the bumper shell. Saab 9-5 4D M06-...
  • Page 6 28 Insert the cable terminals as follows: 1 Black (BK) 2 Brown (BN) 3 Yellow (YE) 4 Blue (BU) 5 Orange (OG) 6 Grey (GY) 29 Affix tape and fit a cable tie on the rubber grommet. Saab 9-5 4D M06-...
  • Page 7 35 Cars with towbar: Fit the connector for the tow- bar wiring harness. 36 Cars with towbar: Fit the bolts and nut plates holding the towbar to the body. Tightening torque 40 Nm (30 lbf ft) Saab 9-5 4D M06-...
  • Page 8 Tighten the screws. 42 Use cable ties (x17) to secure the wiring har- ness along its entire route. Gather excess wiring harness and secure it above the wheel housing. Saab 9-5 4D M06-...
  • Page 9 · 1.8 - 1.3 m: 2 tones/second · 1.3 - 0.9 m: 3 tones/second · 0.9 - 0.3 m: from 5 to 12 tones/second in close stages · 0.3 m: continuous tone Saab 9-5 4D M06-...