Download
Share
Print this page
Saab 32 025 902 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Saab Manuals
  4. Automobile Electronics
  5. 32 025 902
  6. Installation instructions manual
Saab 32 025 902 Installation Instructions Manual

Saab 32 025 902 Installation Instructions Manual

Saab 9-3
Hide thumbs

Advertisement

Quick Links

Download this manual
900
MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS
SITdefault
Saab 9-3
Parking assistance (SPA)
Accessories Part No.
32 025 902
32 025 903
32 025 904
32 026 045
4D, see page 2-13
5D, see page 14-30
CV, see page 31-42
MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE
Group
9:40-08
May 07
Installation instructions
SCdefault
Date
Instruction Part No.
32 025 940
Saab 9-3
Replaces
32 025 940 Oct 06
F930A042

Advertisement

loading
Need help?

Need help?

Do you have a question about the 32 025 902 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Saab 32 025 902

Summary of Contents for Saab 32 025 902

  • Page 1 MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE SITdefault Saab 9-3 Parking assistance (SPA) Accessories Part No. Group Date Instruction Part No. Replaces 32 025 902 32 025 903 32 025 904 32 026 045 9:40-08 May 07 32 025 940 32 025 940 Oct 06 F930A042...
  • Page 2 5 M03-07: Decor strip, bumper 6 Wiring harness, distance sensor 7 SPA wiring harness 8 Dust cover 9 Cable tie (x8) 10 M08: Tape The following parts must be ordered separately M08: Hole-punching tool M08: Distance sensor (x4) M08: Holder (x4) Saab 9-3...
  • Page 3 3 Remove the two nuts holding the rear bumper air shield against the body and the two bolts holding the bumper shell against the wheel housings. 4 Lower the car. 5 M03-07: Remove the decor strip from the rear bumper. Saab 9-3...
  • Page 4 7 Remove the panel in the luggage compartment side trim. 8 M03-07: Remove the side scuff plates. 9 Remove the clips and fold aside the side trims on the left and right-hand sides. 10 Remove the rear lamp clusters. Saab 9-3...
  • Page 5 13 M08: Release the bumper's upper mounting by the rear lamp clusters. 14 Remove the bumper shell by pulling the sides outwards and then pulling the bumper shell rear- wards. Important Place the bumper on a soft, clean surface. Saab 9-3...
  • Page 6 17 Fit the kit's wiring harness. Fit the red cable to connector A1 in position 1. Fit the green cable to connector A1 in position 4. 18 Fit the lock. Plug connector A1 into the blue con- nector. Saab 9-3...
  • Page 7 19 Remove the rubber plug from under the left- hand rear lamp cluster. 20 Connect the ground cable. 21 Connect the control module and fit it into the slots on the rear fuse box. 22 Position the wiring harness and secure with cable ties. Saab 9-3...
  • Page 8 The connector sockets for the distance sensors should point towards the right-hand side of the car. 28 M03-07: Fit the wiring harness for the sensors in the bumper shell groove. 29 M03-07: Fit the support to the bumper shell. Saab 9-3...
  • Page 9 Fit the tape and holders for the sensors in accordance with the markings in the bumper shell. Important The connector sockets for the distance sensors should point towards the right-hand side of the car. Saab 9-3...
  • Page 10 31 M08: Fit the wiring harness in the support for the bumper shell. 32 M08: Fit the support to the bumper shell. WARNING Check that the wiring harness is not pinched. Incorrect fitting can damage the wiring harness and cause a short-circuit/fire. Saab 9-3...
  • Page 11 36 M03-07: Fit the bolts for the bumper shell which are located under the rear lamp clusters. 37 Fit and connect the rear lamp clusters. Check the fit against the boot lid moulding. Saab 9-3...
  • Page 12 39 Fit the side trims. 40 M03-07: Fit the side scuff plates. 41 Fit the panels and the clips in the luggage com- partment's side trims. 42 M03-07: Fit the scuff plate and lower the lug- gage compartment floor. Saab 9-3...
  • Page 13 “Add”. close stages · 0.3 m: continuous tone Note The diagnostic tool will, on some occasions, need to retrieve a security code in TIS. Information on what to do will be displayed on the diagnostic tool display. Saab 9-3...
  • Page 14 5 M06-07: Protective shell, bumper 6 Wiring harness, distance sensor 7 Wiring harness, rear harness 8 Cable tie (x8) 9 Bracket 10 M08: Tape The following parts must be ordered separately M08: Hole-punching tool M08: Distance sensor (x4) M08: Holder (x4) Saab 9-3...
  • Page 15 4 Remove the screws to the wheel housing. 5 Lower the car and open the tailgate. 6 Insert a screwdriver in the hole to reach under the catch for the bumper shell. Bend up using the screwdriver to release the catch. Saab 9-3...
  • Page 16 F930A406 7 Pull the bumper shell away from the holders. 8 Release the catches using a screwdriver. Detach the shell from the moulding. 9 Lift off the bumper shell. Important Place the bumper on a soft, clean surface. Saab 9-3...
  • Page 17 32 025 940 17 F930A407 10 Pull the cellular block from the bumper shell lugs. 11 M06-07: Remove the corner protective mould- ings and the protective shell by inserting tool 82 93 474 under the shell to release the clips. Saab 9-3...
  • Page 18 Fit the tape and holders for the sensors in accordance with the markings in the bumper shell. Important The connector sockets for the distance sensors should point towards the right-hand side of the car. Saab 9-3...
  • Page 19 13 M08: Fit the wiring harness in the support for the bumper shell. 14 M08: Fit the support to the bumper shell. WARNING Check that the wiring harness is not pinched. Incorrect fitting can damage the wiring harness and cause a short-circuit/fire. Saab 9-3...
  • Page 20 The con- nector should appear out towards the left-hand lamp cluster. WARNING Check that the wiring harness is not pinched. Incorrect fitting can damage the wiring harness and cause a short-circuit/fire. Saab 9-3...
  • Page 21 Press the cellular block in. 20 M06-07: Fit the protective shell by pressing in the clips. Make sure that the sensors are fitted in place. 21 M06-07: Check that all clips are secured into the bumper shell. Saab 9-3...
  • Page 22 22 Fold down the rear seat backrests. 23 Remove the left-hand C-pillar trim. Use 82 93 474 Removal tool to remove the cover plate. 24 Remove the left-hand side bolster. Use 82 93 474 Removal tool to remove the clips. Saab 9-3...
  • Page 23 32 025 940 23 F930A644 25 Remove the luggage compartment floor. 26 Cars with subwoofer: Lift up the subwoofer. 27 Remove the scuff plate's clips using 84 71 179 Removal tool, clips and lift up the scuff plate. Saab 9-3...
  • Page 24 32 Lift the cover away from over the storage com- partment. 33 Remove the luggage compartment lighting lens and insert the bulb holder through the hole in the side trim. 34 Remove the trim so that the clips release. Saab 9-3...
  • Page 25 36 Fit the kit's wiring harness. Fit the red cable to connector A1 in position 1. Fit the green cable to connector A1 in position 4. 37 Fit the lock. Plug connector A1 into the blue con- nector. Saab 9-3...
  • Page 26 26 32 025 940 F930A647 38 Connect the ground cable to the grounding point. 39 Fit the kit's control module on the bracket by the electrical centre and plug in the connectors. 40 Position the wiring harness and fit the straps. Saab 9-3...
  • Page 27 43 Fit the cover over the storage compartment. 44 Fit the screw. 45 Fit the cover. 46 Fit the mounting for the cargo guard (if fitted). 47 Fit the two-stage rivet. 48 Fit the clip to the mounting in the body. Saab 9-3...
  • Page 28 28 32 025 940 F930A649 49 Fit the scuff plate. 50 Cars with subwoofer: Lower the subwoofer and screw it in. 51 Fit the luggage compartment floor. Saab 9-3...
  • Page 29 32 025 940 29 F930A650 52 Fit the left-hand side bolster. Check that the belt is not twisted. 53 Fit the left-hand C-pillar trim. 54 Fold up the backrests. Saab 9-3...
  • Page 30 0.9 - 0.3 m: from 5 to 12 tones/second in rectly. close stages 61 Raise the car. · 0.3 m: continuous tone 62 Fit the spoiler's centre nuts. 63 Lower the car and check the fit of the bumper shell. Adjust as necessary. 64 Close the tailgate. Saab 9-3...
  • Page 31 5 M04-07: Decor strip, bumper 6 Wiring harness, distance sensor 7 SPA wiring harness 8 Cable tie (x8) 9 M08: Tape The following parts must be ordered separately M08: Hole-punching tool M08: Distance sensor (x4) M08: Holder (x4) Saab 9-3...
  • Page 32 3 Remove the two nuts that hold the rear bumper air shield to the body and the bolts that hold the bumper shell to the wheel housings. 4 Lower the car. 5 M04-07: Remove the rear bumper's decor strip. Saab 9-3...
  • Page 33 8 Remove the left-hand side trim's clips and move the trim aside. Unhook the strap on the rear of the side trim (certain cars) and unplug the con- nector from the luggage compartment lighting. Remove the side trim. Saab 9-3...
  • Page 34 Bend the screwdriver up to release the catch. 12 Remove the bumper shell by pulling the sides outwards and then pulling the bumper shell rear- wards. Important Place the bumper on a soft, clean surface. Saab 9-3...
  • Page 35 15 Fit the kit's wiring harness. Fit the red cable to connector A1 in position 1. Fit the green cable to connector A1 in position 4. 16 Fit the lock. Plug connector A1 into the blue con- nector. Saab 9-3...
  • Page 36 18 Fit the ground cable. 19 Position the new wiring harness and secure the wiring harness with cable ties. 20 Connect the control module and fit it into the slots on the rear fuse box. Saab 9-3...
  • Page 37 25 M04-07: Fit the distance sensors into the decor strip mountings. Important The connector sockets for the distance sensors should point towards the right-hand side of the car. 26 M04-07: Fit the wiring harness for the sensors in the bumper shell groove. Saab 9-3...
  • Page 38 Fit the tape and holders for the sensors in accordance with the markings in the bumper shell. Important The connector sockets for the distance sensors should point towards the right-hand side of the car. Saab 9-3...
  • Page 39 28 M08: Fit the wiring harness in the support for the bumper shell. WARNING Check that the wiring harness is not pinched. Incorrect fitting can damage the wiring harness and cause a short-circuit/fire. 29 Fit the support to the bumper shell. Saab 9-3...
  • Page 40 33 M04-07: Fit the bolts for the bumper shell which are located under the rear lamp clusters. 34 Fit and connect the rear lamp clusters. Check the fit against the boot lid moulding. Saab 9-3...
  • Page 41 36 Align the left-hand side trim, connect the lug- gage compartment lighting and hook in any strap. Fit the clips. 37 Fit the side scuff plates. 38 Fit the scuff plate and fit the carpet on the lug- gage compartment floor. Saab 9-3...
  • Page 42 “Add”. close stages · 0.3 m: continuous tone Note The diagnostic tool will, on some occasions, need to retrieve a security code in TIS. Information on what to do will be displayed on the diagnostic tool display. Saab 9-3...

This manual is also suitable for:

32 025 90332 025 90432 026 045