Advertisement
Quick Links
9-5
SITdefault
Saab 9-5 5D M06-
Parking assistance (SPA)
Accessories Part No.
32 025 687
Important
To install the kit the car must be equipped with
towbar wiring harness provision.
MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS
MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE
Group
9:40-07
SCdefault
Installation instructions
Date
Instruction Part No.
Sep 05
32 025 690
Saab 9-5 5D M06-
Replaces
E930A384
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Saab 32 025 687
Summary of Contents for Saab 32 025 687
- Page 1 SCdefault Installation instructions MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE SITdefault Saab 9-5 5D M06- Parking assistance (SPA) Accessories Part No. Group Date Instruction Part No. Replaces 32 025 687 9:40-07 Sep 05 32 025 690 E930A384 Important To install the kit the car must be equipped with towbar wiring harness provision.
- Page 2 2 Plastic nut (x2) 3 Distance sensor (x4) 4 Holder (x4) 5 Connector bracket 6 Wiring harness, distance sensor 7 SPA wiring harness 8 Connector 9 Cable tie (x15) 10 Cable tie 11 Cable tie (x2) Saab 9-5 5D M06-...
- Page 3 8 Remove the D-pillar trim, secured with clips. 9 Remove the parcel shelf support, 1 cover and 3 screws. 10 Remove the side bolster by first pulling its top edge so that the lock tongue releases. Then unhook the lower edge. Saab 9-5 5D M06-...
- Page 4 Work carefully during removal so that paint dam- age is avoided. 18 Cars with towbar: Remove the bolts for both reinforcements. 19 With help from an assistant, lift the bumper out backwards. Important Place the bumper on a soft, clean surface. Saab 9-5 5D M06-...
- Page 5 Connect the wiring harness to the sensors and refit the foam sections and the member. WARNING Check that the wiring harness is not pinched. Incorrect fitting can damage the wiring harness and cause a short-circuit/fire. Saab 9-5 5D M06-...
- Page 6 34 Apply tape and a new cable tie (small) on the rubber grommet. 35 Fit the left-hand mounting bracket for the bumper shell under the left-hand tail lamp. The wiring harness must be located inside the bracket. Saab 9-5 5D M06-...
- Page 7 Affix anti-rattle tape and secure with a cable tie to avoid rattle. 40 Connect the wiring harness to the control mod- ule and mount the control module on the floor. Tighten the plastic nuts. Saab 9-5 5D M06-...
- Page 8 47 Cars with towbar: Fit the connector for the tow- bar wiring harness. 48 Cars with towbar: Fit the bolts and nut plates holding the towbar to the body. Tightening torque 40 Nm (30 lbf ft). 49 Lower the car. Saab 9-5 5D M06-...
- Page 9 56 Fit the luggage compartment floor. · 0.3 m: continuous tone 57 Lift in the cargo guard. 58 Fit the cover between the left-hand rear door and the backrest and fold back the rear seat backrests and seat cushions. Saab 9-5 5D M06-...
Need help?
Do you have a question about the 32 025 687 and is the answer not in the manual?
Questions and answers