M-Zone1 Button - Denon AVC-A1SR Operating Instructions Manual

[3] Dolby Headphone recording
• When RECOUT mode is set to "source", with the AVC-A1SR it is possible to output signals encoded in
the Dolby Headphone mode from the recording output terminal and record them on a separate recorder.
1
The Dolby Headphone play mode is set when
headphones are connected to the PHONES
jack during playback in the DOLBY/DTS
surround mode.
2
When this is done, signals encoded in the
Dolby Headphone mode are automatically
output from the recording output terminals
(analog and digital) and can be recorded.
3
Select the parameters and set the desired
mode, then record. (Refer to the
SURROUND "Dolby Headphone" page 25.)
[4] Outputting a program source to an amplifier, etc., in a different room (M-ZONE1 mode)
1
Press the M-ZONE1 button.
M-ZONE 1
(Main unit)
2
Select the source you want to
FUNCTION
output appears on the set's
display.
(Main unit)
[5] Outputting a program source to an amplifier, etc., in a different room (M-ZONE2)
1
Press the REC/M-ZONE2 button
REC /
M-ZONE 2
until "M-ZONE2 "
appears on the set's display.
(Main unit)
2
Select the source you want to
FUNCTION
record appears on the set's
display.
• The MULTI indicator lights.
• The indicator for the selected
(Main unit)
program source light.
• When the AVC-A1SR is in the
RECOUT mode, the source
cannot be output using the M-
ZONE2 buttons on the remote
control unit.
3
Start playing the source to be output.
• For operating instructions, refer to the
manuals of the respective components.
1
NOTE:
⁄0
Do not disconnect the headphones during recording.
1 2
3
Start playing the source to be output.
• For operating instructions, refer to the
manuals of the respective components.
1, 2 1 2
2
Display
PHONO CD TUNER DVD / VDP TV / DBS
MULTI VCR -1 -2 -3 V.AUX TAPE -1 -2
M - Z O N E 2 S O U R C E
NOTES:
• The signals of the source selected in the M-
ZONE2 mode are also output from the TAPE and
VCR recording output terminals.
• Digital signals are not output from the MULTI
ZONE1 audio output jacks.
Playback using the external input (EXT. IN) jacks
2 1
1 Set the external input (EXT. IN) mode.
EXT. IN
Press the EXT. IN (on the EXT. IN button on the remote control unit)
to switch the external input.
(Main unit) (Remote control unit)
The play mode switches as shown below each time the button is pressed.
EXT. IN-1 EXT. IN-2
Once this is selected, the input signals connected to the FRONT-L, FRONT-R, CENTER, SURR.-L (surround
left), SURR.-R (surround right), SB-L (surround back left) and SB-R (surround back right) channels of the
EXT. IN jacks are output directly to the front (left and right), center surround (left and right) and surround
back (left and right) speaker systems as well as the pre-out jacks without passing through the surround
circuitry.
In addition, the signal input to the SW (subwoofer) jack is output to the PRE OUT SW (subwoofer) jack.
Playback using the external input jacks (EXT.IN-1 and EXT.IN-2)
q When the "ANALOG" mode is selected at "EXT.IN SETUP" at system setup: The surround playback
mode button does not function.
w When the "DSP" mode is selected at "EXT.IN SETUP" at system setup: The surround playback mode
button functions.
Press the SURR.PARA button to display the surround parameters screen.
Select the parameter (jog stick up/down) and select the setting value (jog
stick left/right).
Press the SURR.PARA button to complete.
• Input CH parameter
2 CH:
Select when the input source being played is a 2-channel source.
MULTI CH:
Select when the input source being played is a multi-channel source.
2
INPUT ANALOG
MODE
or or
(Main unit) (Remote control unit)
ENGLISH
2
2
1
Cancelling the external input mode
To cancel the external input (EXT. IN) setting, press
the INPUT MODE or ANALOG button to switch to the
desired input mode.
23