Panasonic KX-HCM110A Instruction Manual page 3

Registration with the "Viewnetcam.com FREE DDNS service"
By registering with the Viewnetcam.com FREE DDNS service, you can
create a personalized web address at which your camera's live video
can always be found on the Internet. For detailed information, access
"http://www.viewnetcam.com".
To register with the "Viewnetcam.com FREE DDNS service",
check [Register with Viewnetcam.com] and click [Next > ].
When [Do not register with Viewnetcam.com] was selected at step
•
skip to step .
The Enter Network Password window is displayed.
Enter the user name and password that were set,
and click [OK].
After a while, the "Viewnetcam.com FREE DDNS
service" website is displayed. Follow the displayed
instructions for registration.
• If the message "Failed to configure the router's Port Forwarding by UPnP"
is displayed, your router may not support UPnP
TM
Enable your router's UPnP
router's manual and try Automatic Setup again. For more information about
setting up a router, refer to the Panasonic Network Camera support web-
site at http://panasonic.co.jp/pcc/products/en/netwkcam/
• If the message "Failed to register with Viewnetcam.com." is displayed, con-
firm that the router is connected to the Internet.
When "Setup completed" is displayed, make a note
of the URL in the blank below and click [To Single
Camera page].
• When [Enable] was selected
at step in the "To Set Up
Internet Access to the Camera".
Note
• The port number must be specified at the end of camera URL.
For example
Using port 80: http://(Cameraname).viewnetcam.com
or http://IP Address
Using any other port: http://(Cameraname).viewnetcam.com:Port Number
or http://IP Address:Port Number
• Make a note of the URL for the camera.
• The URL for the local network access may be different from the one set up on
the previous page. Make a note of the URL here again.
When the Single Camera page is displayed, the
setup is completed.
If Security Warning window is displayed to install ActiveX Controls,
•
click [Yes].
To install ActiveX Controls on Microsoft Windows XP Service Pack 2,
•
see "Security Warning window on Microsoft Windows XP Service
Pack 2".
TM or UPnP TM is not enabled.
or set Port Forwarding manually following the
• When [Disable] was selected at
step in the "To Set Up
Internet Access to the Camera".
•
The image is a simulated screen image.
Note
• The banner is displayed only when Internet
access is allowed on the camera.
• To ensure that the most current image is
displayed, Internet Explorer should be
configured as follows. This will not have any
negative result on normal use.
1. While viewing any website, click [Tools]
[Internet Options].
2. In the section "Temporary Internet Files",
click [Settings] and check [Every visit to the
page].
Setting up the Camera Using the MAC Address on the Setup Program
The Setup Program may not list any cameras due to your firewall or
antivirus software settings on your PC. If you cannot disable your firewall
or antivirus software, you can set up the camera using the camera MAC
address as shown below.
Enter the camera MAC address in the data field,
and click [Set up camera].
Note
The cameras MAC address can be found on the sticker affixed to the rear of
the camera (see page 9 of the Operating Instructions on the Setup CD-ROM
for details).
,
After confirming the network settings, click [OK].
• After about a minute, the Security: Administrator page is displayed.
Enter the user name and password, and click [Save].
The Enter Network Password window is displayed. Enter the
user name and password that were set, and click [OK].
When the Single Camera page is displayed, the setup
is completed.
• If Security Warning window is displayed, click [Yes].
• See page 19 of the Operating Instructions on the Setup CD-ROM for
Security Warning window when using Microsoft Windows XP Service Pack 2.
Note
• See page 17 of the Operating Instructions on
the Setup CD-ROM for the Single Camera
page.
• If you enable Internet access to the camera,
follow the procedures below.
• When you are using a router supporting
UPnP TM
1. Enable the Auto Port Forwarding feature
on the UPnP page (see page 62 of the
TM
Operating Instructions on the Setup CD-
ROM).
2. Register with the DynamicDNS service
on the DynamicDNS page (see page 65
of the Operating Instructions on the
Setup CD-ROM).
3. Confirm the Internet access to the
camera (see page 13 of the Operating
Instructions on the Setup CD-ROM).
If you cannot access the camera, see
page 9 of the Troubleshooting on the
Setup CD-ROM.
• When you are using a router not
supporting UPnP TM
Follow the procedures shown on page 64 of
the Operating Instructions on the Setup CD-
ROM.