Advertisement

Quick Links

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RCHD24-1 and is the answer not in the manual?

Questions and answers

Summary of Contents for Revo RCHD24-1

  • Page 3: Compliance Notice Of Fcc

    Network Camera WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. COMPLIANCE NOTICE OF FCC: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
  • Page 4: Important Safeguards

    User’s Manual Important Safeguards 1. Read Instructions 10. Overloading All the safety and operating instructions should be read Do not overload wall outlets and extension cords as this can before the appliance is operated. result in the risk of fire or electric shock. 2.
  • Page 5: Table Of Contents

    Network Camera Table of Contents Chapter 1 — Introduction ................1 Features ....................1 Typical Applications ................. 1 Chapter 2 — Installation................2 Package Contents ..................2 Dimensions ....................2 Illustrated Parts List .................. 2 Factory Reset ..................3 Input/Output Device Ports ................ 4 Mounting ....................
  • Page 6 User’s Manual...
  • Page 7: Chapter 1 - Introduction

    Network Camera Chapter 1 — Introduction This manual is intended for users of the network camera and includes instructions for using and managing the camera on the network. Features This network camera compresses live video and transmits the video over Ethernet connections. The camera can be accessed, configured and managed by using the INIT (Integrated Network Installation Tool) program or NVR.
  • Page 8: Chapter 2 - Installation

    User’s Manual Chapter 2 — Installation Package Contents  Network Camera  Software CD (INIT software and User’s Manual)  Camera User’s Manual (this document)  Mount Kits Dimensions Illustrated Parts List < Dome Cover > ① Side Cable Access Hole...
  • Page 9: Factory Reset

    Network Camera < Body > ① IR LED ② Lens ③ Rotation Base ④ Pan Base ⑤ Factory Reset Switch ⑥ Bottom Cover ⑦ Input/Output Device Ports ⑧ Cable Access Hole ⑨ Tilt Adjustment Screw  Side Cable Access Hole, Cable Access Hole: Allows you to feed wires and cables for connection to power, devices, and Ethernet.
  • Page 10: Input/Output Device Ports

    User’s Manual Input/Output Device Ports ① Video Out ② FGND ③ Network LED ④ Network Port ⑤ Power LED  Video − CVBS, GND: Connect two wires from the cable to the camera and the other connector from the cable to a monitor. This is intended for video preview while adjusting the camera. Configure the video signal (NTSC or PAL) for video output in Remote Setup (System –...
  • Page 11: Mounting

    Network Camera Mounting Mounting Template 1. Screw the bottom cover to the wall or ceiling by using the mounting screws provided with the camera. Use the mounting template provided with the camera. 2. Connect the external devices, network. 3. Adjust the angle of the lens for the proper view angle. Refer to the View Angle section below for details.
  • Page 12: Appendix

    User’s Manual Appendix LED Indicators LED Status Description Unlit No power connected to the unit. Power LED Flicker The unit is booting. The unit is operating. Network LED The unit is connected to a network. Power LED & Flicker The unit is upgrading the software. Network LED sequentially Connector Pin Outs...
  • Page 13 Network Camera VIDEO Video Signal NTSC or PAL (programmable) Compression Algorithm H.264 (Four levels) Compression 352x240, 640x360, 704x480, 1280x720, 1920x1080 Resolution Bitrate Control H.264 –CBR / VBR Maximum Frame Rate 15 ips @ 1920x1080 + 15 ips @ 640x360 (images per second) Multistream Live 1, Live 2 INPUTS/OUTPUTS...

Table of Contents