Tv Operation; Starting Setup - Hitachi LE39E407 Owner's Manual

Starting setup

The Setup Wizard appears the first time you turn on the
TV, and assists you to specify the Air/Cable setting, and
program your channels automatically.
IMPORTANT: Make sure that the antenna or cable TV system
connection is made.
1
To turn on the TV, press POWER. (POWER indicator on the
front of the unit changes green. It may take approx. 10 seconds
for a picture to appear on screen.) The Initial Setup Wizard
begins.
Please select your preferred language
English
Français
Español
Select Ok
2
Press ▲ or ▼ to your desired language, then press SELECT.
3
Press ◀ or ▶ to your desired time mode, then press ▼ to the
next setting.
4
Press ◀ or ▶ to select your time zone, then press ▼ to the
next setting.
• In the rare event that you live within broadcast range of two
stations in two different time zones, the TV may recognize
the wrong station for the auto clock set.
5
Press ◀ or ▶ to select daylight saving time on or off.
6
Press SELECT to go to the next step.
7
Select Home/Retail by pressing ▲ or ▼ to select "Home" or
"Retail".
8
Press SELECT to go to the next step.
9
Press ▲ or ▼ to select signal type (Air/Cable) that you using,
SELECT.
10
Auto Channel Scan will begin. After the scan is completed,
a TV channel appears on the screen.
• Depending on the reception condition, it may take up to 30
minutes to complete scanning channels. Please allow the
process to complete without interruption.
NOTE:
• If you press EXIT during the "Auto Channel Scan" process,
the Auto Channel Scan will stop and the TV will change to the
normal view. When you make a menu selection, your changes
occur immediately. You do not have to press EXIT to see your
changes.

TV operation

1
2
3
4
Menu Back
VHF/UHF/CABLE CHANNELS
NOTE:
• If a channel with no broadcast is selected, the sound will
automatically be muted.
• It may take a few seconds for a digital channel picture to appear
on screen after being selected.
• To direct tune to a digital channel that is not stored in the
channel list enter the first digits followed by - and press
SELECT. For example if you want to select channel 15-2, press
1, 5, - then press SELECT.
To select the video input source
To view a signal from another device connected to your TV, such
as a VCR player, press INPUT, then press ▲ or ▼ to select the
desired input, then press SELECT.
To turn on the TV, press POWER. (POWER indicator on the
front of the unit changes green. It may take approx.10 seconds
for a picture to appear on screen.)
Adjust the volume level by pressing VOL (VOLUME) + or – .
The volume level will be indicated on the screen by a volume
bar.
If the volume increases, the number of bars also increases.
If the volume decreases, the number of bars also decreases.
Set the Source option to the appropriate selection (see "Air/
Cable selection" on page 18).
Press the Direct Channel Selection Buttons (0-9, –) to
select the channel.
TO SELECT ANALOG CHANNELS
1-9: Press 1-9 as needed. Example, to select channel 2,
press 2, then press SELECT..
10-99: Press the 2 digits in order. Example, to select
channel 12, press 1, 2, then press SELECT.
100-135: Press the 3 digits in order. Example, to select
channel 120, press 1, 2, 0, then press SELECT.
TO SELECT DIGITAL CHANNELS
Press the first digits, then press the – button followed by the
remaining number.
Example: To select channel 15-1, press 1, 5, –, 1, then press
SELECT.
• If a channel is selected with only audio content, "Audio Only"
will be displayed on the screen.
• If a channel is selected with a weak digital signal, "No Signal"
will be displayed on the screen.
• The same program may be available on either an analog
channel or a digital channel. You may choose to watch
either format.
Air Cable
VHF VHF
2-13 2-13
UHF STD/HRC/IRC
14-69 14-36
37-59
60-85
86-94
95-99
100-135
01
(A) (W)
(AA) (WW)
(AAA) (ZZZ)
(86) (94)
(A-5) (A-1)
(100) (135)
(4A)
13 EN