Stuff Equipment This Tuffstuff product has been built to precise quality standards ool Requirements and has been carefully packaged to ensure that damage will not 1.
Page 3
IMPORTANT ASSEMBLY INSTRUCTION NOTE INSTRUCTIONS FOR A SINGLE STATION ASSEMBLY ONLY: FOR STEPS 1 AND 2 YOU WILL NEED SOME HARDWARE THAT IS PROVIDED IN THE AP-70RP BOX. ONCE YOU COMPLETE STEPS 1 AND 2 SKIP TO STEP 5 TO RESUME INSTALLATION. INSTRUCTIONS FOR A MULTI STATION ASSEMBLY ONLY: BEGIN ASSEMBLY IN STEP 3.
Introduction STEP 1 Assembly List Item # Description Qty. REAR POST FLAT WASHER SAE N/P 3/8” FLAT WASHER N/P 3/8 ID X 1 1/2 OD X 3/16 NYLON INSERT LOCK NUT N/P 3/8-16 SOCKET CAP SCREW GR-8 N/P 3/8-16 X 3 BASE FRAME FOOT SUPPORT TUBE BLACK NYLON PULLEY 3/8 X 1 X 3 1/2...
Page 6
STEP 1 WITH AP-70RP STEP 3 Assembly List Item # Description Qty. CENTER POST SOCKET CAP SCREW GR-8 N/P 3/8-16 X 1 FLAT WASHER SAE N/P 3/8” SPLIT LOCK WASHER N/P 3/8” BASE FRAME FOOT SUPPORT TUBE BLACK NYLON PULLEY 3/8 X 1 X 3 1/2 BUTTON HEAD SCREW GR-8 N/P 3/8-16 X 1 3/4 BUTTON HEAD SCREW GR-8 N/P 3/8-16 X 5 FLAT WASHER SAE N/P 3/8”...
Page 8
STEP 5 Assembly List Item # Description Qty. CARRIAGE CHROME SELECTOR POST TOP FRAME BLACK NYLON PULLEY 3/8 X 1 X 3 1/2 BUTTON HEAD SCREW GR-8 N/P 3/8-16 X 1 3/4 BUTTON HEAD SCREW GR-8 N/P 3/8-16 X 2 1/4 BUTTON HEAD SCREW GR-8 N/P 3/8-16 X 4 FLAT WASHER SAE N/P 3/8”...
Page 12
STEP 7 COUNTER BALANCE CABLE ASSEMBLY NOTES: 1. SOME PARTS CUT OUT/NOT SHOWN FOR CLARITY. AP-7000 SERIES HIGH LOW STATION...
Page 13
STEP 8 COUNTER BALANCE CABLE FINAL STEP Assembly List Item # Description Qty. COUNTER BALANCE COUNTER BALANCE CABLE BLACK NYLON PULLEY 3/8 X 1 X 3 1/2 BUTTON HEAD SCREW GR-8 N/P 3/8-16 X 1 3/4 BUTTON HEAD SCREW GR-8 N/P 3/8-16 X 2 1/4 FLAT WASHER SAE N/P 3/8”...
Page 14
STEP 9 Assembly List Item # Description Qty. WEIGHT SHIELD BUTTON HEAD SCREW GR-8 N/P 1/4-20 X 3/4 WEIGHT STACK LID FLAT WASHER USS N/P 1/4” AP-7000 SERIES HIGH LOW STATION...
Maintenance TuffStuff Basic Strength Equipment Safety and General Maintenance All TUFFSTUFF strength equipment is designed and manufactured to offer maximum, long-life service with minimal maintenance. However, safety inspection and routine maintenance in your facility should be the upmost importance in your daily operation. Information presented in these pages will serve as a basic guideline to design your own inspection procedures.
Page 18
Bearing and linear bearings systems have advanced over the years but they must be maintained on a regu- lar basis if you expect them to last and perform effi ciently. TuffStuff uses only the highest quality bearings and linear motion components that are virtually trouble-free but requires the regular preventive maintenance to insure long-lasting performance.
Page 19
T U F F S T U F F L I M I T E D W A R R A N T Y TuffStuff warrants to the original purchaser that TuffStuff equipment will be free from defects in material and workmanship.
Need help?
Do you have a question about the Apollo 7000 series and is the answer not in the manual?
Questions and answers