Troubleshooting; Environmental Protection - Metabo W 22-180 MVT Original Instructions Manual

en ENGLISH
using a vacuum cleaner or by blowing in dry air.
Prior to this operation, separate the power tool from
the power source and wear protective glasses and
dust mask.
Button (9) for adjusting the handle: Occasionally
blow compressed air through the button (when
pressed, in all 3 main handle positions). Prior to this
operation, separate the power tool from the power
source and wear protective glasses and dust mask.

10. Troubleshooting

Machine with "WE..." in the model designation:
- Overload protection: The electronic signal
display (6) lights up and the load speed
decreases dramatically. The motor temperature
is too high! Run the machine in idling until it cools
down and the electronic signal display switches
off.
- Overload protection: The electronic signal
display (6) lights up and the load speed
decreases slightly. The machine is overloaded.
Work with a reduced load until the electronic
signal display goes out.
- Electronic safety stop: The electronic signal
display (6) lights up and the machine was
SWITCHED OFF automatically. If the slew rate
of the current is too high (for example, if the
machine suddenly seizes or kickback occurs), the
machine switches off. Switch off the machine at
the trigger switch (8). Switch it on again and
continue to work as normal. Try to prevent the
machine from seizing. See Section 4.2.
- Restart protection: The electronic signal
display (6) FLASHES and the machine does
not start. The restart protection is active. If the
mains plug is inserted with the machine switched
on, or if the power supply is restored following an
interruption, the machine does not start up. Switch
the machine off and on again.
- When switched on, the machine accelerates
to maximum speed very quickly, i.e. automatic
restriction of the starting current does not work
(soft start). An electronic error exists. Other
safety-related electronic functions are no longer
available. Have the machine repaired immediately
(see 12.).
W 22-180 MVT, W 22-230 MVT, W 24-180 MVT,
W 24-230 MVT, W 26-180 MVT, W 26-230 MVT:
- Switching on the machine reduces the voltage
briefly. Unfavourable mains power conditions may
have a detrimental effect on other machines.
Power impedances less than 0.2 ohm should not
cause malfunctions.
11. Accessories
Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements
and specifications listed in these operating
instructions.
Fit accessories securely. Secure the machine if it is
operated in a bracket. Loss of control can cause
personal injury.
18
See page 4.
A Roughing disc (always use with safety guard
attached)
B Lamellar grinding disc (always use with safety
guard attached)
C Parting safety guard.
D Parting disc (always use with parting safety
guard attached)
E Diamond discs (always use with safety guard or
parting safety guard attached)
F Cup wheel guard (place on machine and secure
with screws (f)). Secure cup wheel as described
in chapter 7.. Use an offset 2-hole spanner if
necessary. Use the wing screws to adjust the
safety guard until the cup wheel protrudes max.
3 mm.(
G Cup wheels (When working with cup wheels,
the special cup wheel guard has to be used for
safety reasons.)
H Offset 2-hole spanner (for securing/loosening
the clamping nut (13) on cup wheels)
I Parting safety guard with guide slot (place on
machine and secure with screws.) (with adapter
for connection to a suitable dust extractor for
extraction of stone dust generated when cutting
stone slabs.)
J Hand guard (for attaching under the additional
side-mounted handle.)
K Extension piece (for working with supporting
discs. Increases the distance between the
spindle and the supporting disc by approx. 35
mm)
L Supporting disc for fibre discs (always attach
using the supporting disc clamping nut
supplied.) (always use with the hand guard
attached.)
M Fibre discs (always use with the hand guard
attached.)
N Steel wire brushes (always use with the hand
guard attached.)
O Bench cut-off stand
P Adjusting nut (13)
Q "Quick" clamping nut (1)
For the complete range of accessories, see
www.metabo.com or the main catalogue.
12. Repairs
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.

13. Environmental Protection

The generated grinding dust may contain harmful
substances. Dispose appropriately.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.