Advertisement
Quick Links
USA Subject to change
www.ferm.com
CAUTION:
Before using this Rotary
Cutting Tool or any of its
accessories, read this
manual and follow all Safety
Rules and Operating
Instructions.
Imported by Ferm BV
0611-24
Art. No. SCM8001
Model. No. RCT-600
4 A Rotary Cutting Tool
with Circle Cutting Guide
• General Safety Rules
• Specific Safety Rules and
Symbols
• Functional Description
• Assembly
• Operation
• Maintenance
• Accessories
www.ferm.com
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Ferm RCT-600
Summary of Contents for Ferm RCT-600
- Page 1 Art. No. SCM8001 Model. No. RCT-600 USA Subject to change 4 A Rotary Cutting Tool with Circle Cutting Guide CAUTION: • General Safety Rules Before using this Rotary • Specific Safety Rules and Cutting Tool or any of its Symbols accessories, read this •...
- Page 2 Exploded view Ill.1 Ferm Ferm...
- Page 3 Spare parts list WARNING: When servicing, use only FERM replacement parts. Use of any other parts may create a safety hazard or cause damage to the tool. ON/OFF switch Any attempt to repair or replace electrical parts on this power tool may create a safety Speed control wheel hazard unless repair is performed by a qualified technician.
- Page 4 Ill.4 Ill.5 Ill.6 Ferm Ferm...
- Page 5 Ill.7 Ill.8 Ill.9 Ferm Ferm...
- Page 6 Ill.10 Ill.11 Ill.12 Ferm Ferm...
- Page 7 Not applicable WARNING: Keep the extension cord clear of the working area. Position the cord so it will not get caught on the workpiece, tools or any other obstructions while you are working with the power tool. Ill.14 Ferm Ferm...
- Page 8 1-year Warranty contain chemicals that can damage, weaken or destroy plastic. This Ferm product carries a one (1) year warranty against defects in workmanship and DO NOT abuse power tools. Abusive practices can damage the tool as well as the workpiece.
- Page 9 • Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is increased risk of electric shock if your body is grounded. • Do not expose power tools to rain or wet conditions. Water entering the power tool will increase the risk of electric shock. Ferm Ferm...
- Page 10 Place circle cutting guide mounting hole (5) over the externally-threaded circle cutting Accessories that may be suitable for one tool may become hazardous when used on guide mounting insert. another tool. NOTE: Make sure pointed pivot pin (6) is pointing away from the tool. Ferm Ferm...
- Page 11 • Never touch the bit during or immediately after use. After use the bit is too hot to be When fastening the drywall in place, do not place nails or screws closer than 12” from the touched by bare hands. box. This will prevent the drywall from becoming deformed under pressure. Ferm Ferm...
- Page 12 WARNING: Before turning the power switch ON, make sure you are holding the direct current tool firmly with both hands. Starting torque will cause the tool to twist. no load speed Set the speed control switch to the appropriate speed. Ferm Ferm...
- Page 13 Use of improper accessories may cause Lock the freehand cutting guide onto the motor housing by pushing the locking lever injury to the operator or damage to the tool. inward toward the motor housing until it snaps into the locked position. Ferm Ferm...
- Page 14 WARNING: Insert the bit all the way into the collet and then pull it back between 1/16” and 1/8”. This creates an air space between the motor shaft and the bit to help protect the bit from overheating. Ferm Ferm...
Need help?
Do you have a question about the RCT-600 and is the answer not in the manual?
Questions and answers