Related Manuals for winsonic MFC1045S-XN40C
Summary of Contents for winsonic MFC1045S-XN40C
- Page 1 User’s Manua - Model #MFC1045S-XN40C WINSONIC ELECTRONICS Co., LTD No.290-1, Wen Chung Rd., Taoyuan City, Taiwan, R.O.C l:+886-3-3704789 ax:+886-3-3704722 E-mail:sales@ewinsonic.com www.ewinsonic.com...
-
Page 2: Table Of Contents
Contents Safety Instruction Product Installation Panel Specification General Description Absolute Maximum Ratings Electrical Specifications Optical Specifications Precautions AD Board Specification Assembly Trouble Shooting... -
Page 3: Safety Instruction
Safety Instruction Read and follow these instructions when connecting and using your LCD monitor: Operation: 1. Keep the monitor out of direct sunlight and away from stoves or any other heat source. 2. Remove any object that could fall into ventilation holes or prevent proper cooling of the monitor＇s electronics. -
Page 4: Product Installation
Product Installation 1. Switch off the power on both your monitor and your computer. The Power Switch is located in the right of the monitor. 2. Connect the power cord to the AC outlet, and connect the power to the monitor through the AC/DC adapter. -
Page 5: Panel Specification
1. GENERAL DESCRIPTION 1.1 OVERVIEW MFC1045S-XN40C is a 10.4” TFT Liquid Crystal Display module with 2-CCFL backlight unit and 30-pin-and-1ch LVDS interface. This product supports 1024 x 768 XGA format and can display true 16.2M colors (6-bits colors with FRC). The inverter module for backlight is not built-in. -
Page 6: Absolute Maximum Ratings
Panel Specification 2. ABSOLUTE MAXIMUM RATINGS 2.1 ABSOLUTE RATINGS OF ENVIRONMENT Value Item Symbol Unit Note Min. Max. Storage Temperature (-20) (+70) ºC Operating Ambient Temperature (-10) (+60) ºC (1), (2) Shock (Non-Operating) (220) (3), (5) Vibration (Non-Operating) (1.5) (4), (5) Note (1) Temperature and relative humidity range is shown in the figure below. -
Page 7: Electrical Specifications
Panel Specification 2.2 ELECTRICAL ABSOLUTE RATINGS 2.2.1 TFT LCD MODULE Value Item Symbol Unit Note Min. Max. Power Supply Voltage -0.3 Input Signal Voltage -0.3 3. ELECTRICAL CHARACTERISTICS 3.1 TFT LCD MODULE Ta = 25 ± 2 ºC Value Parameter Symbol Unit Note... - Page 8 Panel Specification Vcc rising time is 470us +3.3V 0.9Vcc 0.1Vcc 470µs Note (3) The specified power supply current is under the conditions at Vcc = 3.3 V, Ta = 25 ± 2 ºC, f = 60 Hz, whereas a power dissipation check pattern below is displayed. b.
- Page 9 Panel Specification 3.2 BACKLIGHT UNIT 3.2.1 CCFL (Cold Cathode Fluorescent Lamp) CHARACTERISTICS ( Ta = 25 ± 2 ºC) Value Parameter Symbol Unit Note Min. Typ. Max. Lamp Voltage = 7.0mA Lamp Current 770(25 ) Lamp Starting Voltage 960(0 ) (2), Operating Frequency 50,000...
- Page 10 Panel Specification 5. INTERFACE PIN CONNECTION 5.1 TFT LCD MODULE CN1 Connector Pin Assignment Pin No. Symbol Description Note No Connection Ground RX3+ Positive transmission data of pixel 3 RX3- Negative transmission data of pixel 3 Ground RXCLK+ Positive of clock RXCLK- Negative of clock Ground...
- Page 11 Panel Specification 5.2 BLOCK DIAGRAM OF INTERFACE Rx0+ RxOUT 100pF Rx0- TxIN R0-R7 R0-R7 Rx1+ G0-G7 G0-G7 100pF Rx1- B0-B7 B0-B7 Rx2+ 100pF Rx2- Rx3+ 100pF Rx3- Host CLK+ Graphics DCLK 100pF CLK- Controller Timing Controller LVDS Receiver LVDS Transmitter THC63LVDF84A THC63LVDM83A (LVDF83A)
- Page 12 Panel Specification 5.3 LVDS INTERFACE TRANSMITTER INTERFACE RECEIVER TFT CONTROL THC63LVDM83A CONNECTOR THC63LVDF84A SIGNAL INPUT INPUT Host TFT-LCD OUTPUT TxIN0 Rx OUT0 TxIN1 Rx OUT1 TxIN2 TA OUT0+ Rx 0+ Rx OUT2 TxIN3 Rx OUT3 TxIN4 Rx OUT4 TxIN6 TA OUT0- Rx 0- Rx OUT6 TxIN7...
- Page 13 Panel Specification 5.4 COLOR DATA INPUT ASSIGNMENT The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for the color. The higher the binary input, the brighter the color. The table below provides the assignment of color versus data input.
- Page 14 Panel Specification 6. INTERFACE TIMING 6.1 INPUT SIGNAL TIMING SPECIFICATIONS The input signal timing specifications are shown as the following table and timing diagram. Signal Item Symbol Min. Typ. Max. Unit Note Frequency 1/Tc Input cycle to LVDS Receiver Clock Trcl cycle jitter Setup Time...
- Page 15 Panel Specification LVDS RECEIVER INTERFACE TIMING DIAGRAM RXCLK+/- RXn+/- Tlvsu Tlvhd 11 T...
- Page 16 Panel Specification 6.2 POWER ON/OFF SEQUENCE To prevent a latch-up or DC operation of LCD assembly, the power on/off sequence should be as the diagram below. Power Supply 0.9 V 0.9 V 0.1Vcc 0.1V 0.5 T 10ms 50ms 50ms 500ms VALID Signals Power Off...
-
Page 17: Optical Specifications
Panel Specification 7. OPTICAL CHARACTERISTICS 7.1 TEST CONDITIONS Item Symbol Value Unit Ambient Temperature 25±2 Ambient Humidity 50±10 Supply Voltage Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS" Lamp Current Oscillating Frequency (Inverter) Vertical Frame Rate 7.2 OPTICAL SPECIFICATIONS The relative measurement methods of optical characteristics are shown in 7.2. - Page 18 Panel Specification Note (1) Definition of Viewing Angle (θx, θy): Viewing angles are measured by BM5A Normal θx = θy = 0º θy- θ 12 o’clock direction θ = 90º θ = 90º θx− θx+ 6 o’clock θ = 90º θ...
- Page 19 Panel Specification Note (4) Definition of Luminance of White (L Measure the luminance of gray level 255 at center point and 5 points = L (5), where L (X) is corresponding to the luminance of the point X at the figure in Note (7). Note (5) Definition of Cross Talk (CT): CT = | Y –...
- Page 20 Panel Specification Note (7) Definition of White Variation (δW): Measure the luminance of gray level 255 at 5 points δW = Maximum [L (1), L (2), L (3), L (4), L (5)] / Minimum [L (1), L (2), L (3), L (4), L (5)] Horizontal Line 3D/4 : Test Point...
-
Page 21: Precautions
Panel Specification 8. PRECAUTIONS 8.1 ASSEMBLY AND HANDLING PRECAUTIONS (1) Do not apply rough force such as bending or twisting to the module during assembly. (2) It is recommended to assemble or to install a module into the user’s system in clean working areas. The dust and oil may cause electrical short or worsen the polarizer. -
Page 22: Ad Board Specification
AD Board Specification LCD monitor GTR24 OSD operation Control Functions The Monitor control functions are located on the lower side of the panel. The control key description 1. MENU Activate the on-screen-display function ∇ Down / Brightness control ∆ Up / Brightness control Auto AUTO-ADJUSTMENT Power Switch... -
Page 23: Adjustment Procedure
AD Board Specification DJUSTING THE MONITOR The LCD monitor is designed to work with a range of compatible video adapters on the market. Due to the possible deviations between these video adapters, you may make some adjustment to fit the monitor for adapter used. -
Page 24: Brightness Adjustment
AD Board Specification AUTO-ADJUSTMENT WE STRONGLY RECOMMEND THAT YOU USE THIS ITEM TO GET THE OPTIMIZED VISUAL QUALITY. Use the ∇ & ∆ key to select auto-adjustment, and then press Menu Key to get the optimized quality. Or press Auto Key to get the optimized directly. ... - Page 25 AD Board Specification best Screen Settings optimization. H.Position ∇ ∆ Use the & key to select the H.Position item, then press Menu Key to get the best optimization. Use the ∇ & ∆ key to adjust H.Position value. Then press menu key to confirm.
- Page 26 AD Board Specification Phase ∇ ∆ Use the & key to select the Phase item, then press Menu Key to get the best optimization. ∇ ∆ Use the & key to adjust increase or decrease video Quality of the picture. ...
-
Page 27: Language Setting
AD Board Specification Auto Gain ∇ ∆ Use the & key to select Auto Gain, then press Menu Key to get the best color optimization that will be activated the auto adjusting input video color level for the picture. sRGB ∇... -
Page 28: Osd Setting
AD Board Specification OSD Setting ∇ ∆ Use the & key to select the OSD Setting item, then press Menu Key to get the item, t OSD setting selection. You could set up the property of Position, Display Timer, and Transparency of OSD menu. ... -
Page 30: Trouble Shooting
Trouble Shooting If your monitor fails to operate correctly, consult the following chart for possible solution before calling for repairs/RMA. Condition Possible Solution The screen is not synchronized? 1. Check if the signal cable is firmly seated in the socket. 2.