Exhaust Air Connection - Bosch WTMC332RCN Operating, Care And Installation Instructions Manual

Exhaust air connection

The following warnings must be
adhered to without exception.
d
WARNING
1. To reduce the risk of fire, this dryer
MUST BE EXHAUSTED
OUTDOORS.
2. To reduce the risk of fire, do not
use ductwork longer than
recommended. Refer to the
maximum ductwork length table
(see page 12).
3. DO NOT use a plastic, metal foil,
or any other non metal duct with
this dryer. Only rigid or flexible
metal duct shall be used for
exhausting. Metal foil and flexible
metal ducting are NOT the same.
4. DO NOT use more than 2.4 m of
flexible metal ducting.
5. DO NOT use a duct smaller than 4
inches in diameter.
6. DO NOT exhaust the dryer into: a
chimney, wall, ceiling, concealed
space of a building, furnace cold
air duct, attic, crawl space, or any
other ductwork used for venting.
7. DO NOT install a flexible duct in an
enclosed wall, ceiling or floor.
8. DO NOT crush or kink the duct.
9. Do clean and inspect the exhaust
system on a regular basis; at least
once a year.
10. The exhaust duct must terminate
with an approved exhaust vent
hood to prevent back drafts or
entry of birds or other wildlife.
11. DO NOT use exhaust hoods with
magnetic latches.
12. DO NOT assemble the duct work
with screws or fasteners that
extend into the duct. They serve
as an accumulation point for lint.
Joints should be secured with
aluminum tape.
Exhaust air outlet on the dryer
The dryer is delivered with an exhaust
air outlet on the rear of the appliance.
To take account of the spatial
requirements and an existing exhaust
air system, the following connection
options are possible for the exhaust air
outlet:
- on right side of the appliance,
- on the underside of the appliance.
2
3
1 Exhaust air outlet on the rear of the
appliance (standard)
2 Exhaust air outlet on the side (optional)
3 Exhaust air outlet on the underside of
the appliance (optional)
Special exhaust air connections can be
obtained from your dealer, part supplier
or customer service for either
connection type (see page 13).
- Side exhaust kit
- Bottom exhaust kit
A qualified technician should change
the exhaust air outlet to the optional
connection location.
Ductwork
The dryer vent system moves moist air
away as your clothes tumble dry. You
can shorten drying times, save energy
and help ensure the safety of the
system by making sure your dryer's
exhaust duct system is properly
installed and maintained.
Important Points to Consider:
Keep exhaust duct runs (total
q
length of the exhaust duct system
from the dryer to the exhaust hood
outside) as short as possible (refer
to the table Maximum Ductwork
Length" on page 12.)
Use the minimum number of
q
elbows needed when installing the
exhaust duct system. Avoid
placing two 90 degree elbows
adjacent to one another.
Check and clean the exhaust duct
q
system and exhaust hood at least
once each year, and any time you
suspect dryer performance is
decreased.
Remove accumulated lint to
prevent diminished air flow or
clogging of the system.
1
Professional cleaning is
recommended annually and when
attaching your dryer to a previously
used exhaust duct system.
Replace any plastic or metal foil
q
venting sections with rigid metal or
flexible metal ducting. Rigid metal
ducting is recommended.
i Correct exhaust system installation
is the responsibility of the
consumer.
Problems that result from
incorrect installation are not
covered by the appliance
warranty.
Exhaust ducting which is longer than
specified in the maximum ductwork
length table on page 12 is not
permitted. Not adhering to this table
will extend drying time, cause lint to
accumulate and affect dryer
performance and dryer life time.
11