Electrical Connection; Exhaust Air Connection - Bosch Nexxt DLX Series Operating, Care And Installation Instructions Manual
Hide thumbs
Also See for Nexxt DLX Series:
- Operating, care and installation instructions manual (80 pages) ,
- Operating & installation instruction (94 pages) ,
- Operating instructions manual (93 pages)
Table of Contents
Advertisement
Installation location
d
d
WARNING!
Do not install the dryer:
-
outdoors,
-
in an environment with dripping
water,
-
near flammable materials,
-
in rooms which are at risk of frost,
-
in rooms which may contain gas
or other fuels,
-
in cupboards with lockable doors
or in alcoves.
-
with other fuel burning appliance
in the same closet.
The installation room must be well
ventilated, otherwise the dryer will
operate below optimum performance.
Do not operate the dryer at
temperatures above 104 °F (40 °C) and
below 41 °F (5 °C). Low temperatures
affect the automatic program sequence
and may prolong the drying times.
The installation surface for the dryer
must be clean, level and firm. Do not
install the appliance on carpets!
Compensate for uneven floors with the
height adjustable feet.
Install the dryer and level side to side
and front to back. Use a bubble level.
Never remove the height adjustable
feet!
The size of the installation area
depends on the dimensions of the
dryer. Ensure that there is adequate
room for the swivel range of the door!
d
d
WARNING!
If installed in a garage, the dryer
must be installed on a substantial
platform at least 18 inches above
the floor to reduce the liklihood of
igniting flammable vapors and be
located or protected so it cannot be
damaged by a moving vehicle
Dimension
Weight
125 lbs
a
27.0" (686 mm)
(56 kg)
(56 kg)
b
31.8" (808 mm)
with
with
c
37.2" (945 mm)
packaging
packaging
d
19.7" (500 mm)/
143 lbs
angle
170-180°
(64 kg)
If installing the dryer in a closet, observe
the minimum distances according to
the following table:
Minimum Installation Clearances
Closet
Sides
0" (O mm)
Top
12" (3O5 mm)
Rear*
0" (O mm)
* as close to wall as gas piping and venting
will allow.
Important information concerning
minimum distances:
-
Depending on the location of the
exhaust air connection, an
additional minimum distance of
5½ inch (14 cm) must be provided
on this side for pipes/brackets (see
page 9).
-
Distances above the indicated
minimum dimensions reduce the
risk of mold formation behind the
appliance.
-
Additional distances reduce noise
transmission.
-
Additional distances facilitate
installation and service.
-
If the dryer is installed in a small
room, the doors of the room must
be fitted with vents of a specified
minimum size.
The dryer door is delivered with hinges
on the right. If required, the door hinges
can be switched to the left side.
If the door hinges are to be changed
over, please contact your dealer or our
customer service team (see page 22).
Electrical connection
GROUNDING INSTRUCTIONS
This appliance must be grounded. In
the event of a malfunction or
breakdown, grounding will reduce the
risk of electrical shock by providing a
path of least resistance for the electric
current. This appliance features a cord
with an equipment grounding
conductor and a grounding plug. The
plug must be plugged into an
appropriate outlet which has been
properly installed and grounded in
accordance with all local regulations
and ordinances.
d
d
WARNING
Improper connection of the
equipment grounding conductor
may result in electric shock. Have
the appliance checked by
a qualified electrician or service
technician if you are in doubt as to
whether the dryer has been properly
grounded.
Do not modify the plug provided with
the appliance - if it will not fit in the
outlet, have a proper outlet installed by
a qualified electrician or exchange the
cord with an appropriate one rated for
the dryer.
d
d
WARNING
The dryer must only be connected
to an individual branch circuit via a
socket which has been properly
installed and grounded.
The household electrical voltage must
correspond to the voltage specification
on the dryer (rating plate).
You will find the rating plate on the
inside of the front panel.
Connection specifications as well as
the electrical requirements are
stipulated on the appliance nameplate.
Make sure that:
Page 6
Hide quick links:
Advertisement
Chapters
Table of Contents
