Related Manuals for Jasic JP-25C
Summary of Contents for Jasic JP-25C
-
Page 1: Operator Manual
Plasma 25C Air Plasma Cutting machine Order code ! JP-25C OPERATOR MANUAL... -
Page 2: Serial Number
Your new product Thank you for selecting this Jasic Technology, Wilkinson Star product. This product manual has been designed to ensure that you get the most from your new product. Please ensure that you are fully conversant with the information provided paying particular attention to the safety precautions. The information will help protect yourself and others against the potential hazards that you may come across. -
Page 3: Safety Precautions
Safety Precautions These general safety norms cover both arc welding Insulate yourself from work and ground using dry insulating mats or covers big enough to prevent any physical contact machines and plasma cutting machines unless with the work ground. otherwise noted. Never touch the electrode if you are in contact with the work The equipment must only be used for the purpose it was ground, or another electrode from a different machine. - Page 4 Do not weld on coated metals, unless the coating is Replace the coverings and protections and close all doors removed from the weld area, the area is well ventilated, and when the intervention is finished, and before starting the while wearing an air-supplied respirator. The coatings on equipment.
- Page 5 Keep your head and face away from the cylinder valve outlet RF Declaration when opening the cylinder valve. Equipment that complies with directive 2004/108/EC Always secure the cylinder safely concerning electromagnetic compatibility (EMC) and the technical requirements of EN60974-10 is designed for use in Never deface or alter any cylinder industrial buildings and not those for domestic use where electricity is provided via the low voltage public distribution...
-
Page 6: Product Overview
Product Overview CUT25 is a plasma cutting machine model developed from the original CUT series plasma cutting machines. It inherits the mature and stable inverter technology of CUT series: With PWM technology and high-power MOSFET switching devices, it converts the DC voltage, which is rectified from 50Hz/60Hz input AC voltage, to 100KHz AC high voltage. -
Page 7: Technical Data
Technical data MODEL CUT25 Rated input voltage (V) 230V AC±10% Rated input frequency (Hz) 50/60 Rated input capacity (KVA) No-load voltage (V) 230±15 Cutting current (A) Rated output voltage (V) Rated duty cycle (%) Efficiency (%) Power factor Insulation class Protection class IP21S Arc ignition... - Page 8 Cutting speed guide Cutting thickness (mm) Mild steel Galvanised Stainless steel Aluminium Brass Copper Cutting speed {m/mm)
- Page 9 Controls Input cable Work return cable socket Torch connection. Mains switch- Power led - It indicates that the input power is normal. Overheat led.- This indicator will turn on when the machine is overheated due to overload or over current and the output has been disabled. Leave the machine on to allow the internal components to cool.
-
Page 10: Installation
Installation Unpacking Check the packaging for any signs of damage. Carefully remove the machine and retain the packaging until the installation is complete. Location The machine should be located in a suitable position and environment. Care should be taken to avoid moisture, dust, steam, oil or corrosive gases Place on a secure level surface and ensure that there is adequate clearance around the machine to ensure natural... - Page 11 Operation It is recommended to initiate the cutting from the Before starting any cutting activity ensure that you have edge of workpiece, unless penetration is needed. suitable eye protection and protective clothing. Also take the necessary steps to protect any persons within the area.
-
Page 12: Maintenance And Troubleshooting
Maintenance and troubleshooting The following operation requires sufficient professional Troubleshooting knowledge on electric aspects and comprehensive Before arc cutting machines are dispatched from the factory, safety knowledge. Make sure the input cable of the they have already been checked thoroughly. The machine machine is disconnected from the electricity supply and should not be tampered with or altered. -
Page 13: Electrical Schematic
Electrical schematic... -
Page 14: Parts List
Parts list Cut 25 - (JP-25C) - Page 15 Part no Description Part no Description 10027491 Handle 10021916 Spring Line button 10046083 Machine Cover 10043261 Air compressor 10046082 Central insulation board 10046113 Shock absorber 10001873 10016489 Foot 10046115 Clamp 10046058 Bottom panel 10020602 EMC board 10007278 Solenoid valve 10046084 Insulation Board 10044457 Filter...
- Page 16 JP-25C AIR PLASMA CUTTING MACHINE Order code ! JP-25C © Wilkinson Star Limited Issue 1 January 2014 Product is subject to change without notice...
Need help?
Do you have a question about the JP-25C and is the answer not in the manual?
Questions and answers