Rear Panel - Onkyo DV-SP800 Service Manual

QQ
3 7 63 1515 0
PANEL VIEW-3

REAR PANEL

VIDEO
OUTPUT
L
ANALOG
OUTPUT
R
European models.
12
IN/
OUT
TE
L 13942296513
OPTICAL
Shapes of jacks vary depending on the area in which it was
purchased.
1 VIDEO OUTPUT COMPONENT jacks
If your TV has component inputs, you can connect a component
video cable to your TV and to your DVD Player for ideal video
quality. The component Video Cable only carries the video signal;
remember to connect the left and right audio cables. If you connect
a TV that is compatible with a Progressive scan signal, you can
enjoy both Interlaced and Progressive scan.
2 VIDEO OUTPUT S VIDEO jack
If your TV or monitor has an S-video input, clear picture
reproduction is possible by connecting the player to your TV or
monitor via the S-Video jack.
You can switch between [S1] and [S2] S-video output from the
Setup menu.
3 VIDEO OUTPUT VIDEO jack
Connect to the video input on a TV or monitor or AV amplifier or
receiver with video input capability.
4 AC INLET
Use to connect the power cord to the wall outlet.
5 ANALOG OUTPUT CH 1/CH 2 jacks
Use to output two-channel audio (analog) to the audio stereo
inputs on a TV or stereo amplifier.
6
ANALOG OUTPUT FRONT/SURR 1/CENTER/
SUBWOOFER jacks
Use to output 5.1 channel audio (analog) to the 5.1 channel
www
discrete inputs on an amplifier. If you are connecting to a
receiver that has both digital and analog input jacks for DVD
player connection, it may be beneficial to make both connections.
.
http://www.xiaoyu163.com
1 2 3
COMPONENT S VIDEO VIDEO
Y P P R
B
CH 1 CH 2 FRONT SURR 1 CENTER SURR 2
L
SURR
1 1+2
R
SUB
OPTICAL
WOOFER
5 6 7 8
13
AV CONNECTOR 1 AV CONNECTOR 2
OUT
DIGITAL OUTPUT
REMOTE
COAXIAL
CONTROL
x ao
y
i
http://www.xiaoyu163.com
8
DIGITAL OUTPUT
REMOTE
CONTROL
COAXIAL
9 10 11
7
SURR 2 jacks
Use when making connections to 7.1 channel analog inputs.
(Make sure the SURR 1/1+2 selector switch is set to 1+2.)
8 SURR 1/1+2 selector switch
When using 2 channel surround, select 1, when using 4 channel
surround, select 1+2. Audio will be output 3dB lower when 1+2 is
selected. The same audio is output from SURR 1 and from
SURR 2.
9 DIGITAL OUTPUT OPTICAL jack
SACD & DVD AUDIO/VIDEO PLAY
DV-SP 800
MODEL NO.
Use to output the digital audio signal recorded on discs. You can
Q Q
3 6 7 1 3
output the digital signal via the optical output jack to an AV amplifier
or receiver.
10
DIGITAL OUTPUT COAXIAL jack
Use to output the digital audio signal recorded on discs. You can
output the digital signal via the coaxial output jack to an AV
amplifier or receiver.
11 jack
Use to connect this player to another component bearing the
mark. This lets you control this unit as though it were a component
in a system.
(The components will not function as a system with only
connections. Be sure to connect the audio connection cables
correctly as well).
(European models)
12 AV CONNECTOR 1 (IN/OUT) jack
Use a 21-pin SCART cable to connect to a TV, monitor or video
component compatible with this type of connection. Outputs both
audio and video (composite only) when the unit is powered on.
When the unit is in standby mode, this jack becomes an input for
audio and video (RGB, S, and composite).
13 AV CONNECTOR 2 (OUT) jack
Use a 21-pin SCART cable to connect to a TV or monitor
compatible with this type of connection. Outputs audio and video
(RGB, S, and composite) when the unit is powered on.
When the unit is in standby mode, this jack outputs the audio and
video input from the AV CONNECTOR 1 jack.
u163
.
2 9 9 4 2 8
4
SACD & DVD AUDIO/VIDEO PLAYER
DV-SP 800
MODEL NO.
1 5 0 5 8 2 9 9 4
m
co
DV-SP800
9 9
AC INLET
2 8 9 9