Page 1
XR-H560MD EZ,K 3 7 63 1515 0 SERVICE MANUAL L 13942296513 BASIC TAPE MECHANISM : 6ZM-1 AR3 MD / CD STEREO SYSTEM BASIC CD MECHANISM : 4ZG-1 Z3RNSMDJM BASIC MD MECHANISM : ZZG-6 D This Service Manual is the "Revision Publishing" and replaces "Simple Manual"...
http://www.xiaoyu163.com SPECIFICATIONS 3 7 63 1515 0 L 13942296513 • Design and specifications are subject to change without notice. • Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. •...
http://www.xiaoyu163.com PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs laser. Therefore, be sure to follow carefully the CAUTION 3 7 63 1515 0 instructions below when servicing. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous WARNING! radiation exposure.
http://www.xiaoyu163.com Precaution to replace Optical block (KSS-213F) 3 7 63 1515 0 Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode. 1) After the connection, remove solder shown in the right figure.
http://www.xiaoyu163.com DISASSEMBLY INSTRUCTIONS 1. Disassembling the MD block 3 7 63 1515 0 Remove the CABI, STEEL. (Screws: 4 pcs on the right side, 4 pcs on the left side and 7 pcs on the rear: Total 15 screws) Remove the 13 screws (UTT2+3-8) A and remove the rear panel. After removing the connectors from the TUNER C.B and the FUN, remove the rear panel.
Page 7
http://www.xiaoyu163.com Remove the four screws (BVT2+3-10) C. Remove the ZZG-2. 3 7 63 1515 0 HLDR, MD ZZG-2 2. Disassembling the MD block and the service position Remove the ZZG-2. Remove the two screws (UT2+2.6-6 GLD) D from the PLATE, SHLD REAR. Remove the PLATE, SHLD REAR. L 13942296513 Remove the four screws (U+2+2.6-6) E from the PLATE, SHLD TOP.
Page 8
http://www.xiaoyu163.com Remove the four screws (UT2+2.6-6 GLD) F and remove the PLATE, SHLD BOTTOM. 3 7 63 1515 0 PLATE, SHLD BOTTOM The MD block is ready to be placed in the service position. Connect the MD block with the interface board using the extension FFC as shown below.
Page 9
http://www.xiaoyu163.com 3. Disassembling the elevator 3 7 63 1515 0 Rotate the WORM-WHL, JT (the gear shown by the arrow below) counterclockwise to move the elevator to the top position. Note: If the PANEL, SHLD BOTTOM is not removed, the elevator cannot be removed. WORM-WHL, JT L 13942296513 Remove the FF-CABLE, 9P 1.0 from the LOAD C.B.
Page 10
http://www.xiaoyu163.com While lifting up the elevator slightly, remove an end of the shaft of the elevator from the guide hole of the CHAS ASSY, SHLD. 3 7 63 1515 0 Remove the other end of the shaft and tilt the elevator as shown below. While tilting the elevator, short the shorting land.
Page 11
http://www.xiaoyu163.com 4. Disassembling the elevator block 3 7 63 1515 0 Remove the screw (UT2+2.6-6 GLD) G and the screw (VTT+2-4) H. Then remove the HLDR, MECHA SUB. HLDR, MECHA SUB Remove the four screws (S-SCREW, MD T) I and remove the ZZG-1 from the HLDR ASSY, MECHA. L 13942296513 ZZG-1 HLDR ASSY, MECHA...
Page 12
http://www.xiaoyu163.com 5. Remove the two screws (VTT+2-4) A. 3 7 63 1515 0 Remove the PLATE ASSY, SLIDE L and the PLATE, SLIDE R in the direction of the arrow. Remove the screw (VW+1.7-5 W/O MFZN2C) B. Remove the HEAD, OWH RF325-74A. Re-assembling: Align the axis of the PLATE ASSY, SLIDE L with the arrow mark of the CAM, LOAD.
Page 13
http://www.xiaoyu163.com 7. Remove the CAM, LOAD in the direction of the arrow. 3 7 63 1515 0 Re-assembling: Move the LEVER ASSY, CAM in the direction of the arrow mark as much as it can be moved. Move the reference hole of the CAM, LOAD closer to the axis of the LEVER, SW H as close as possible. Align the CAM, LOAD with the gear of the GEAR, IDLER2.
L 13942296513 Remove the three 3 screws (VT3-5) and open the cassette • tray halfway. After pulling up the XR-H560MD and closing the tray again, remove it. • Perform the azimuth adjustment through the hole on the top surface.
http://www.xiaoyu163.com NOTE ON BEFORE STARTING REPAIR • CD service position 3 7 63 1515 0 Remove the CABI, STEEL. Remove the three screws (BVT2+3-10) A. Turn over the unit and remove the CABI, BOTTOM. L 13942296513 Remove the two FFCs (13P and 6P) the CD block from the hook of the CABI, BOTTOM. Loosen the two screws (QT2+3-12) B of the 4ZG-1 CABI, FR.
Page 16
http://www.xiaoyu163.com Remove the hooks in the direction of the arrow. (The hooks are used at the both sides.) Pull the CABI, BOTTOM up to the 3 7 63 1515 0 diagonally top right and remove it. HOOK Lay down the unit and remove the 3ZG-2 mechanism. Extend the 3ZG-2 mechanism using the respective extension jigs.
Page 23
http://www.xiaoyu163.com 3 7 63 1515 0 • Regarding connectors, they are not stocked as they are not the initial order items. The connectors are available after they are supplied from connector manufacturers upon the order is received. CHIP RESISTOR PART CODE Chip Resistor Part Coding Figure Resistor Code...
http://www.xiaoyu163.com TRANSISTOR ILLUSTRATION 3 7 63 1515 0 B C E B C E B C E 2SB1626 2SK2158 2SB1625 2SB1370 KTA1298 2SA1235 2SD2495 2SD2494 RN1305 2SA1514 RN2305 2SA1588 RT1N141C 2SC3052 2SC3906 RT1N144C RT1P141C 2SC4116 RT1P144C 2SD1306 RT1P441C CSD1306 DTA123EKA E C B E C B GD S...
http://www.xiaoyu163.com TEST MODE < MD > 1. How to Start Up the MD Test Mode 7. Checking the Operation of Loading Mechanism/OWH 3 7 6 3 1 5 1 5 0 While pressing the MD function key, insert the AC plug to the power outlet. The operations of the loading mechanism and the OWH are checked by the procedure below.
Page 45
http://www.xiaoyu163.com 9. Checking the Servo Operation 3 7 63 1515 0 9-1. Checking the Focus Search/Spindle Kick 1 (Check of S-Curve) 1) The focus search operation and the spindle kick operation can be performed continuously by pressing the REPEAT key in the “ALL SVoFF”...
Page 46
http://www.xiaoyu163.com (ELECTRICAL ADJUSTMENT ) 3 7 63 1515 0 All adjustments and checks of the MD disc are performed using the test mode. 1. Temperature Compensation Adjustment In principle, do not perform the temperature compensation adjustment during the normal maintenance or repair work. If the adjustment value is found out that it is far out of the specification values shown in this service manual, perform the temperature compensation adjustment under the environment where the ambient temperature can be precisely measured.
Page 47
http://www.xiaoyu163.com 3-2. Checking the IVR, EFB, Focus/Tracking/Sled Gains of the MO Disc 3 7 63 1515 0 • Adjustment procedure 1) Move the pickup to the center track or around the center track of a disc using the B.SKIP and F.SKIP keys. 2) Press the PLAY key to display “FOCUS ON!”.
Page 48
http://www.xiaoyu163.com 4. Error Rate Check (PIT Disc) 3 7 63 1515 0 • Test Point: Check the indication on the display • Test Disc: TGYS-1 or equivalent • Adjustment procedure Load the TGYS-1. Move the pickup to the center track or around the center track of a disc using the B.SKIP and F.SKIP keys. Press the MODE (MD) key to display “SEL PIT”.
Page 49
http://www.xiaoyu163.com TEST MODE < CD > 1. How to Start the CD Test Mode 2. How to Exit the CD Test Mode 3 7 63 1515 0 While pressing the function CD button, insert the AC plug to Exit the CD test mode by any of the following procedures. the wall outlet.
Page 53
http://www.xiaoyu163.com PRACTICAL SERVICE FIGURE < TUNER SECTION > 1. Clock Frequency Check 3 7 63 1515 0 Settings: • Test point: TP2 (CLK IC770 pin30) < FM SECTION > Method: Set to MW 1602kHz and check that the test IHF Sensitiviy: Less than 13dB point becomes 2052kHz±45Hz (EZ).
http://www.xiaoyu163.com IC DESCRIPTION IC, LC876580W 3 7 63 1515 0 Pin No. Pin Name Description I-DISH CD DISH No. detection input. I-MD1 MD door SW input. I-MD2 — Not used. _______________ I-STEREO/I-DRF Connected to tuner/stereo detection and CD ASP LA9240M pin-54 DRF. Connected to the front shift resistor BU2099 3 DATA, main shift resistor 4094 2 O-DATA DATA, and tuner PLL IC LC72131 4 DI.
Page 56
http://www.xiaoyu163.com IC, CXD2652AR 3 7 63 1515 0 Pin No. Pin Name Description MNT0 Monitor output terminal. MNT1 Monitor output terminal. MNT2 Monitor output terminal. MNT3 Monitor output terminal. SWDT Microprocessor serial interface data input. SCLK Microprocessor serial interface shift clock input. XLAT Microprocessor serial interface latch input.
Page 57
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description Address output to external DRAM. Address output to external DRAM. (Not used). DVSS — Digital GND. External DRAM output enable. ________ XCAS CAS output to external DRAM. Address output to external DRAM. ________ XRAS RAS output to external DRAM.
Page 58
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description DCHG Connected to the low impedance power supply. Error signal input to the laser digital APC. ADFG ADIP2 binary-converted FM signal (22.05±1 kHz) input. F0CNT Current source setting output terminal to CXA2523. XLRF Latch output for CXA2523 control.
Page 59
http://www.xiaoyu163.com IC, CXP81952 3 7 63 1515 0 Pin No. Pin Name Description MCAS — MRAS — Not used. — AMUTE Audio mute signal output. Serial clock output for EEPROM interface. Serial data output for EEPROM interface. Serial data input for EEPROM interface. EEPROM interface chip select signal output.
Page 60
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description ARDY Ready signal input for system control interface. Serial data input for system control interface. SOUT Serial data output for system control interface. ACLK Serial clock output for system control interface. XLAT CXD2652 interface latch signal output.
Page 61
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description — — Not used. — Connected to VSS. — Open. (Not used) — Connected to VSS. — Connected to VDD. — — — Not used. DRVMUTE BA5970FP mute signal output. —...
http://www.xiaoyu163.com MODEL NO. SX-WNH898 SPEAKER DISASSEMBLY INSTRUCTIONS 3 7 63 1515 0 Type.1 Type.4 Insert a flat-bladed screwdriver into the position indicated by the TOOLS arrows and remove the panel. Remove the screws of each speaker 1 Plastic head hammer unit andthen remove the speaker units.