Page 1
SX-NDPH2100 RC-ZAS04 XR-H2000 • This Service Manual is the "Revision Publishing" and replaces "Simple Manual" XR-H2000 (EZ,K), (S/M Code No. 09-005-427-6T2). • If requiring information about the CD mechanism, see Service Manual of AZG-1 ZD3RNDM, (S/M Code No. 09-001-335-3N8). u163 S/M Code No.
http://www.xiaoyu163.com TABLE OF CONTENTS 3 7 63 1515 0 PROTECTION OF EYES FROM LASER BEAM DURING SERVICING ............3 PRECAUTION TO REPLACE OPTICAL BLOCK ....................3 SPECIFICATIONS ..............................4 ACCESSORIES / PACKAGE LIST ........................4 MODEL NO. MX–NH2000 ELECTRICAL MAIN PARTS LIST ........................ 5 ~ 8 TRANSISTOR ILLUSTRATION ..........................
http://www.xiaoyu163.com PROTECTION OF EYES FROM LASER BEAM DURING SERVICING 3 7 63 1515 0 This set employs laser. Therefore, be sure to follow carefully CAUTION the instructions below when servicing. Use of controls or adjustments or performance of proce- dures other than those specified herin may result in WARNING!! hazardous radiation exposure.
http://www.xiaoyu163.com IC DESCRIPTION (MX-NH2000) IC, UPD780228GF-065-3BA 3 7 63 1515 0 Description Pin No. Pin Name K-SCAN Key scan output. RHYTHM-CS Chip select output to IC, BU9990-03FS. (Not used) RHYTHM-SCLK Clock output to IC, BU9990-03FS. (Not used0 RHYTHM-SD Data output to IC, BU9990-03FS. (Not used) PLL CE PLL IC chip enable output.
Page 21
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Name Description Pin No. I-RDS-SIG Tuner tuning signal level A/D input. I-MIC MIC input level detection. KEY1 KEY1 input. KEY2 KEY2 input. I-TEMPO TEMPO input (100Hz, 3.3kHz). I-GE-2 DEMO, TIMER, CLOCK, SPICE A, AUTO SPICE / FILL IN input. I-GE-1 JOG, SPICE B SW input.
Page 22
http://www.xiaoyu163.com IC, M65849BFP-631D 3 7 63 1515 0 Description Pin No. Pin Name MCLKONT Controls build-in-clock generation circuit with external R. TEST1 Test mode "H" : Normal / "L" : Test. CLOCK Clock input via serial bus. Strobe input via serial bus. DATA Data input via serial bus.
http://www.xiaoyu163.com MODEL NO. FX-NH2000 3 7 63 1515 0 ELECTRICAL MAIN PARTS LIST REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION C358 87-010-183-080 C-CAP,S 2700P-50 B C359 87-010-183-080 C-CAP,S 2700P-50 B 87-A20-455-010 IC,HA12211 C360 87-010-183-080 C-CAP,S 2700P-50 B 87-A20-355-010 IC,CXA1553P C363...
Page 36
http://www.xiaoyu163.com 3 7 63 1515 0 REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION CN701 87-A60-062-010 CONN,05P V 9604S-05C DECK C.B D701 87-070-278-010 LED,SLZ-738A-24S PGRN D702 87-002-787-080 LED,SEL 6215S RED CN502 87-099-756-010 CONN,15P 9604 S F S701 87-A90-095-080 SW,TACT EVQ11G04M...
http://www.xiaoyu163.com TRANSISTOR ILLUSTRATION (FX-NH2000) 3 7 63 1515 0 B C E E C B 2SK2158 2SA1296 2SC1815GR 2SC3052 2SC3266GR CSA1362 KTC3198GR RN1410 RT1N141C RT1N144C RT1P141C E C B 2SA933SRS L 13942296513 u163 – 37 – http://www.xiaoyu163.com...
http://www.xiaoyu163.com IC DESCRIPTION (FX-NH2000) IC, M38503M4-094FP T4 3 7 63 1515 0 Description Pin No. Pin Name – IC power supply. V-REF – Connected to VCC. AVSS – Connected to GND. – Not connected. I-AUTO-1 Input of DECK 1 reel platform pulse. I-AUTO-2 Input of DECK 2 reel platform pulse.
Page 43
http://www.xiaoyu163.com 3 7 63 1515 0 Description Pin No. Pin Name O-DIMMER Ordinarily “H”. When MX-NH2000 is in DIMMER 1 or 2 mode: “L”. I-KEY2 KEY input 2. AD input. I-KEY1 KEY input 1. AD input. I-MS MS input. AD input. I-HOLD System power supply monitor.
http://www.xiaoyu163.com IC DESCRIPTION (GE-NH2000) IC, LC866448W 3 7 63 1515 0 Pin No. Pin Name Description O-C.SHIFT Micro computer clock shift output. PRO LOGIC PRO LOGIC LED output. 3-STEREO 3 STEREO LED output. PHANTOM PHANTOM LED output. NORMAL NORMAL LED output. –...
http://www.xiaoyu163.com SPEAKER DISASSEMBLY INSTRUCTIONS 3 7 63 1515 0 Type.1 Type.4 Insert a flat-bladed screwdriver into the position indicated by the TOOLS arrows and remove the panel. Remove the screws of each speaker 1 Plastic head hammer unit and then remove the speaker units. 2 (() flat head screwdriver 3 Cut chisel How to Remove the PANEL, FR...
Need help?
Do you have a question about the XR-H2000 and is the answer not in the manual?
Questions and answers