Installation Notes ..........8 Setup for living areas ........8 Setup as a PC sound system ......8 Connecting ..............9 Connecting components ........9 Connecting headphones ........9 Connecting a microphone ........9 Connecting satellite speakers ......10 Connecting to the mains ........10 • Concept C...
® All trademarks are the property of the respective The speakers are designed for the playback of music owners. and speech from external components. Only use the Concept C as described in this ® Bluetooth and the Bluetooth symbol installation guide and the online manual. Any other...
, Pb = Lead Fuse T 2,5 AL / 250 V Protection class II - double insulated T2.5 AL 250 V Risk of electric shock – Do not open the housing. Unplug power cord before replac- ing the fuse. • Concept C...
Overview Package contents 1 x Subwoofer Concept C 1x Remote control 1x USB cable 1x AC power cable 1x Speaker cable (15 m) 2x satellite speakers C25FCR. • Check that all items have been delivered and that nothing is damaged.
Page 7
Service jack (only for the service technician) BLUETOOTH / AUX IN / USB LED 2 (blue=BLUETOOTH, green=AUX IN, red=USB) SUBWOOFER VOLUME Volume control SPEAKER OUT Analog audio output for satellite speakers POWER ON / OFF Power switch AC power socket Fuse • Concept C...
PC Concept C workstation, that is, the area where the monitor and listener are located. • Please position the speakers within the grey areas. Setup as PC sound system • Concept C...
1. Unplug all devices to be connected to the subwoofer in order to prevent them from accidentially turning on. 2. Connect the Concept C to the components as shown in the following examples. • PC: – Connection to USB (5) using a USB cable.
– The strands of the speaker cables are marked with different colours or shapes. 1. On the back of the Concept C are the analog outputs SPEAKER OUT (13) for the satellite speakers. Run the speaker cables from the subwoofer to each satellite speaker.
1. Turn on the Concept C. 2. Place the remote control at a distance of no more than 25 cm away from the Concept C. 3. Hold the side button (3) down until the LED ring (2) starts to blink, and then release it.
When the subwoofer is on, the green LED 1 POW- green ER / STANDBY (9) will light up. • To put the Concept C in Standby mode: Push and hold the middle of the control dial (1) of the remote control until the LED ring (2) blinks three times.
You can fi nd more information about this in the instruction manual of your smartphone or tablet. 4. After the scan, “Concept C” should appear in the list of the detected devices. Select this item from the list of found devices.
In case of stubborn marks, a mild soap solution may be used. – Under no circumstances should caustic cleaning products, rubbing alcohol, thinners, petrol, etc. be used. Such cleaning agents may damage the delicate surface of the subwoofer. • Concept C...
Playback is noisy. Generally speaking, the Make sure that the external player emits a clear Concept C is a very low-noise signal to the Concept C. system. In most cases, speaker systems with excellent resolution in the high range area expose the poor quality of a signal source (e.g.
DIN EN 55024: 2011 DIN EN 60065:2011 DIN EN 62321:2005 ETSI EN 301489-1 V1.9.2 ETSI EN 301489-9 V1.4.1 ETSI EN 300328 V 1.8.1: Verordnung 1275/2008 Verordnung 0278/2009 Edgar van Velzen Geschäftsführer 06. März 2015 Ausstellungsdatum / Date of issue: • Concept C...
12 kg without satellite speakers 13,6 kg including satellite speakers Further technical data can be found on our website. No responsibility is assumed for the correctness of this information. Technical changes, typographical errors and other errors reserved. • Concept C...
Page 20
Please contact customer service with any questions, suggestions or comments Lautsprecher Teufel GmbH Phone: 00800 - 200 300 40 No responsibility is assumed for the BIKINI Berlin (toll-free) correctness of this information. Budapester Straße 44 Fax: +49 (0)30 - 300 930 930...