Clock Setting; Sleep Mode - KeepRite ProComfort DLFAHH/DLCAHB Owner's Manual

T- ON button (Timer ON)
To set when you want the unit to turn On at the end of a selected
time period, use the button labeled "T- ON" on the remote
controller. Press this button to make the clock icon disappear,
replaced with the word "ON" (blinking). Press "+" or"- " buttons
to adjust timer setting 1 minute at a time. Press and hold "+"
or "- " button to set timer more quickly. Press"T- ON" button
again to confirm setting, and the word "ON" stops blinking.
To cancel, press"T- ON" button again.
T- OFF button (Timer OFF)
NOTE: Under Timer On and Off status, you can set T- ON
and T- OFF simultaneously. Before setting timer, be sure to
set clock to correct time.

CLOCK SETTING

Press this button to set clock time. The Clock icon on remote
controller blinks. Within 5 seconds, press "+" or "- " button to set
clock time. With each press of the "+" or "- " buttons, the clock
time increases or decreases by 1 minute. To quickly adjust the time
setting, press and hold "+" or "- " button for 2 seconds.
Release the button when you have reached the desired time setting.
Press the "CLOCK" button to confirm the time, and clock icon
stops blinking.
NOTE: Clock time adopts 24- hour mode. A 12- hour format is
not available.

SLEEP MODE:

The unit automatically adjusts room temperature during your sleep
time. This slight change in temperature will not affect your comfort
level due to the natural effects that sleeping has on the body, however
it saves on energy consumption and lowers your electric bill.
The unit has four Sleep Modes to select from. Press the SLEEP
button to select Sleep 1, Sleep 2, Sleep 3, Sleep 4 modes or Cancel.
The SLEEP icon appears.
TRADITIONAL MODE - SLEEP 1
In Traditional Mode the unit slowly relaxes the room set
temperature by up to 4_F until Sleep Mode is cancelled.
Cooling Mode
Fig. 10 - Cooling and Heating Modes
EXPERT MODE - SLEEP 2
In Expert Mode the unit adjusts the room set temperature at a rate
based on the starting set temperature value. Sleep Mode continues
until cancelled.
Cooling Mode
Fig. 11 - Cooling and Heating Modes
DIY MODE SLEEP 3
You are required to enter eight (8) room set point values for eight
(8) hours of run time. The last room set point value is maintained
until the sleep mode is cancelled.
In Sleep Mode 3, press the "Prog" button to enter the setup mode.
The remote controller displays "1:00" in the time location. Use the "+"
and "- " buttons to select the desired room set point for the first hour
of run time. Then press the "Prog" button to save the set point.
Repeat this sequence for the eight (8) room set point values. After
all eight (8) values have been entered, the remote controller
automatically reverts to standard time and temperature display, and
the Sleep 3 Mode starts.
At any time, you may press the "ON/OFF," "Mode," "Timer,"
"Sleep" or "Turbo" buttons to cancel the Sleep 3 Mode.
NOTE: During this procedure, if no button is pressed within 10
seconds, the remote controller automatically exits the sleep
curve setting and resumes the original display. If the ON/OFF,
MODE, TIMER, SLEEP, COOLING or HEATING button is
pressed during the setting or inquiry procedure, the remote
controller exits the sleep curve setting.
SIESTA MODE 4:
In Siesta Mode the unit automatically changes the room
temperature every 30 minutes based on the room temperature
setting. The Sleep Mode continues until cancelled.
Heating Mode
NOTE: Sleep function can not be set in AUTO mode.
LIGHT:
This function allows the user to turn the display ON or OFF on
the front panel.
Press the light icon
OFF. The remote control displays the Light Icon
Combination of "+" and "- " Buttons:
Press "+" and "- " buttons simultaneously for 8 seconds to lock or
unlock the keypad. If the remote control is locked,
In this case, pressing any button,
Heating Mode
acknowledge the keypad is locked. Repeat the process to unlock
the remote controller.
WIFI Button:
Press and hold this button for three seconds to turn WIFI function
on or off. See the "Operation of Smart Control" section for more
information.
Only the set point temperature appears on the front panel and on
the remote controller.
7
Cooling Mode
Fig. 12 - Siesta Mode
to turn the indoor unit front panel ON or
blinks three times to
Heating Mode
.
is displayed.